Panasonic Color Video Camera Aw E560 Operating Instructions

-9-
Pin No. Signal Pin No. Signal1 Composite Video Output 11 RCB Transmission2 GND 12 Control (Command)3 G/Y/Y Output 13 +9.2 V RCB4 R/PR/C Output 14 DC 12 V Output5 GND 15 DC 12 V Input6 RCB Detect 16 DC 12 V Input7 EXT SUB In 17 RCB Reception8 B/PB Output 18 GND9 GND 19 GND
10 G/L Input 20 Not used
 Remote Connector (REMOTE)
 DC Input Connector (EXT DC IN) 10. Remote Connector (REMOTE)
Input terminal dedicated to control signals from the
optional Remote Control Box (WV-CB700A) and the
Remote Control...

-10- 13. Video/RGB Output Connector (VIDEO/RGB)
Composite/Y signal, RGB/Y-C/component signal and
synchronizing signal are output from this connector.
* Refer to Page 41 for signal selection.
The optional cable WV-CA9T5 or WV-CA9T9 must be
used for connection to this connector.
Pin No. Signal Pin No. Signal1 GND 6 SY/COMP2 GND 7 SYNC3 R/PR/C 8 GND4 G/Y/Y 9 C/NC
5 B/PB/NC
The multiplex adaptor WV-PS550 is connected to this
connector when using a coaxial multiplex system.  The
WV-RC700A and WV-PS550 can be...

-11- 15. G/L Signal 75-ohm ON/OFF Switch (75½ON/OFF)
A terminating switch for G/L signals at Items 16 and
17.
16. G/L VBS/HD Input Connector (G/L IN - VBS/HD)
Signals synchronized with the reference signal are to
be supplied to this connector when the camera is to
be synchronized with the reference signal.  VBS/BB,
VS and HD signals are to be automatically deter-
mined.
17. G/L VD Input Connector (G/L IN - VD)
Same as Item 16 except that VD signal is to be sup-
plied when input signal at Item 16 is HD....

-12-
FLANGE BACK ADJUSTMENT1. Fully open the iris by shooting a dark object.  (Iris
selection switch should be set to M.)
2. Loosen the flange back lock knob.
3. Aim the camera at any object over 2 meters away from
the camera.
4. Set the lens to its TELE end first and adjust its focus
with the focus ring.
5. Set the lens to its widest angle next and adjust its
focus with the flange back adjust ring.
6. Adjust the focus ring and the flange back adjust ring
alternately for the best focus within the...

ZOOM/FOCUSREMOTE
EXT DC IN
PAGE
ITEM(AWC)
UP(ABC)DOWN(BAR)
IRIS
SEE MANUAL
CAUTIONCONNECT TO SPECIFIED
CLASS 2 POWER SUPPLY
ONLY SEE MANUAL
VBS/HD75¶
VD
VIDEO/RGB
CONTROLVIDEO OUT G/L IN
ON
OFF
-13-
n CONNECTION OF DEVICE WITH A COMPOSITE INPUT CONNECTORCONNECTIONSCaution :
The connection and installation should be done by qualified service personnel or system installers.
Refer any servicing to qualified service personnel.
1. Connect this to a 12V DC class 2 power supply only.
2. To prevent fire or shock...

-14-
How to assemble the power cable:The power cable is to be assembled with the connector
provided with the camera.

1. Prepare the wire.
2. Fix with a screw if necessary.
Put the casing and the rubber bushing on after solder-
ing wires to the connector.Caution :
To prevent fire or shock hazard, the UL listed wire VW-
1, style 1007 should be used as for the cable for 12V
DC Input Connector.
1
24
3AWG24 or larger
3/16
(5 mm) 

-15- Input signals to an RGB monitor or image processor must
be supplied from the VIDEO/RGB connector through the
optional D Sub/BNC cable WV-CA9T5 or D Sub/D Sub
cable WV-CA9T9.NOTES:
• Output signals at the VIDEO/RGB connector can be
selected from the INITIAL SET menu.
• SYNC level can be selected from the INITIAL SET
menu.
nCONNECTION OF DEVICE WITH AN RGB MONITOR OR AN IMAGE PROCESSORPin Wires OutputNo. Color Signal3 Red R/PR/C4 Green G/Y/Y5 Blue B/PB6 White Y/COMP
7 Black SYNCWV-CA9T5 Cable...

-16- Connection to the RCU (WV-RC700A) is made through the
optional conversion cable WV-CA26T20 and a studio
cable.
1. Turn RCU power off before connecting cables.
2. Set the cable selection switch of the RCU to MULTI.
3. Connect the 20 pin connector of the conversion cable
to the REMOTE Connector of the camera.  The conver-
sion cable and the studio cable must be connected
with the connector supplied as a standard accessory
with the conversion cable.4. Turn RCU power on and the power indicator lamp...

-17-
nCONNECTION OF A REMOTE CONTROLLER (RCU AND A COAXIAL MULTIPLEX SYSTEM)The optional multiplex adaptor WV-PS550 is used for
connection of a coaxial multiplex system.
1. Turn RCU power off before connecting cables.
2. Connect the optional multiplex adaptor WV-PS550 to
the control connector of the camera through the stan-
dard accessory cable supplied with the WV-PS550.
3. Set the cable selection switch of the RCU to VP.
4. Connect the MPX connector of the multiplex adaptor
and that of the RCU with a...

ALL 1
2USER  SET
ZOOM/FOCUSREMOTE
EXT DC IN
PAGE
ITEM(AWC)
UP(ABC)DOWN(BAR)
IRIS
SEE MANUAL
CAUTIONCONNECT TO SPECIFIED
CLASS 2 POWER SUPPLY
ONLY SEE MANUAL
VBS/HD75¶
VD
VIDEO/RGB
CONTROLVIDEO OUT G/L IN
ON
OFF
-18-
nCONNECTION OF A REMOTE CONTROL BOX (RCB)The RCB (WV-CB700A) and the camera must be connect-
ed with the optional conversion cable WV-CA20T10.
1. Turn RCB power off before connecting cables.
2. Connect the 20 pin connector of the conversion cable
to REMOTE connector of the camera.  The 10-pin...