Panasonic Color Video Camera Aw E560 Operating Instructions

-19-
nCONNECTION WITH MULTIPLE CAMERASnAn example of connection for VBS/BB input (Color lock
mode).
• A special effect generator is used as the source of refer-
ence signals.
• Supply a synchronizing signal (VBS/BB) to the GEN-LOCK
Connectors of both the RCU and the camera.• Adjust the SC phase and H phase at the Program Out
Connector.
There are two other modes such as VS input (No color lock
mode) and HD/VD input (monochrome mode), which
can be selected for your application.
GEN-LOCK
INAUX
INAUTO...

-20-
CONNECTION OF COMPUTER INTERFACE ADAPTOR
The system shown here can remotely control this camera by using the Computer Interface Adaptor WJ-PC500.
The software required for this operation should be obtained locally.
Please contact qualified service personnel for this software.
PC Mode System 1-1
CAMERA 2
IN
MONITOR
OUT
G/L  IN
CAMERA 1  IN
DC12V  IN
CAMERA SELECT
RS-232C/422
ZOOM/FOCUSREMOTEEXT DC IN
PAGEITEM(AWC)UP(ABC)DOWN(BAR)IRIS
SEE MANUAL
CAUTIONCONNECT TO SPECIFIED
CLASS 2 POWER SUPPLY
ONLY...

-21- • The kit WV-CA28T10 has the following two cables in it.
• 20P-BNC cable CA20TBNC
• Pan/Tilt control cable CA28T103
• Connect the camera AW-E560 to the remote control box WV-CB550 with the CA20TBNC coaxial cable.
• Connect the camera AW-E560 to the receiver WV-RC100 with the CA28T103 cable according to the cable connecting instruc-
tions.
• Connect the camera AW-E560 to the remote control box WV-CB550 with two coaxial cables (video signal and G/L signal).
(PSF 1/2M, maximum total length 300 m)
• Use...

-22-
B
Remote  Control  Box  WV-CB 
550
WV-CA12T12
ZOOM/FOCUS CONTROLIRIS CONTROLG/L VIDEO
MONITOR VIDEO
PAN/TILT CONTROLCAMERA VIDEOG/L VIDEO
CONTROL SIGNAL
PAN/TILT CONTROLCoaxial Cable
Pan/tilt Contact
Closure Type
Pan/tilt Control  Cable AW-E560
1/2 Zoom Lens
Pan/Tilt Control Cable
CA28T103 DC12V
DC12V
WV-CB550 Color Monitor
Signal Generator
Receiver
WV-RC100Remote Control
Box 

-23-
• Connecting Receiver and Control Cable CA28T103• The control cable CA28T103 is provided with a circuit board and spacers.
• Assemble the circuit board and spacer with the receiver WV-RC100 (WV-RC150), and connect the control cable to that circuit
board.nCA28T103 CONNECTION PROCEDURE(1) Remove the two screws on the connector board
shown from inside the receiver.(2) Fit the two spacers on the connector board and fasten
the circuit board with the screws removed in Step (1).
ScrewsSpacer
Circuit board,...

-24- (3) Disconnect the connector from connector CN4 on the
process circuit board, and connect it to connector
CN2 on the circuit board mounted. (Cut off or remove
the wire band.)
(4) Connect the lead from the circuit board to the ALARM
DC COM terminal.(5) Connect the control cable CA28T103 to connector
CN1 on the circuit board.
ALARM DC COM
terminal
Circuit board, an 
accessory to the cableProcess circuit board
Connect the 28-pin end of it to the control ter-
minal on the camera.Control cable 

-25-
ADJUSTMENTColor temperature and adjustment of white balance
When carbon is burnt, it develops various colors of light
depending on the temperature.   Natural light can be spec-
ified by color temperature referring to the color developed
when carbon is burnt.
The light of 3,200K (K=Kelvin, -273C equals to absolute
zero temperature 0K) represents the same value (color) as
what develops when carbon is burnt at 3,200K (2,927C).
The relationship between the color temperature of the light
source and...

-26- nAUTOMATIC WHITE BALANCE CONTROL (AWC)
There are two white balance memories, “AWC A” or “AWC
B” for two different light sources color temperatures, with
the white balance setting.  Then, when the two different
light sources are encountered, you may properly operate
the camera by simply change the white balance mode to
either AWC A (A CH) or AWC B (B CH).  There is no need
to readjust the camera to the ambient conditions.
* The preset conditions will be renewed whenever you
input new conditions.
1....

-27- NOTES:
• For white balance setting aim the camera at a
white object and try to position it in the center of
the monitor screen.  The object must appear in
over 10% of the total monitor screen area.  Try to
avoid overly bright object in the scene.
• White balance may not be correctly set if the light-
ing of the object is not strong enough.
• Since the camera has a built-in battery, the set
white balance will be kept in the memory even if
power is turned off.  Therefore, it is not necessary
to reset...

NO.1 ** INITIAL **
R GAIN      +....I....-
B GAIN      +....I....-
T PED       +....I....-
R PED       +....I....-
B PED       +....I....-
PAINTING     OFF
RET   END
-28- nRESET TO 3200K OR 5600K WHITE BALANCE
When the white balance setting is set to either “P SET
3.2K” or “P SET 5.6K” the white balance will be automati-
cally set to the color temperature 3,200K or 5,600K
respectively.
nBLACK BALANCE ADJUSTMENT
[ADJUSTMENT by CAMERA]
Press the ABC (UP) Switch for over 1 second and the
black balances for...