Panasonic Color Video Camera Aw E560 Operating Instructions

-39- 7Red gain adjustment [R GAIN]
8Blue gain adjustment [B GAIN]
When the white balance setting is set to MANU, white
balance can be adjusted by red/blue gain control.
Fine adjustment of white balance can also be made
after AWC by red/blue gain control when the white
balance setting is set to A CH or B CH and the paint-
ing mode is ON.
* A memory is provided for each of MANU, A CH, and B
CH.
If AWC is executed when the camera is used alone,
the memories for A CH and B CH return to the center.
9Total...

-40- !5Detecting Ratio Adjustment [PEAK/AVG]
The ratio of AUTO IRIS/AGC/ELC detected peak to
average can be adjusted in a range of 9 steps.
!6AUTO IRIS Level Fine Adjustment Setting
[AUTO IRIS: ADJ ON/ADJ OFF]
When the mode is set to ADJ ON, fine adjustment of
ALC/ AGC/ELC convergence level can be made with
the iris VR control on the RCU (RCB) if the camera is
used with an RCU (RCB) and the iris mode is set to
AUTO in the SETUP menu.
!7Synchroscan Adjustment
[SYNCHRO-SCAN: 1/525 to 253/ 525]
Shutter...

-41- @5Output Signal Setting 1
[OUTPUT SEL1: R/G/B, Y/C, Y/PR/PB]
Output signals from the VIDEO/RGB connector or
REMOTE connector on the back of the camera can be
selected.
@6Output Signal Setting 2
[OUTPUT SEL2: Y/C, COMPOSITE]
Output signals from the VIDEO/RGB connector on the
back of the camera can be selected.
@7Synchronizing Signal Output Level Setting
[SYNC SEL: 0.3 V/4.0 V]
The synchronizing signal output level from the VIDEO/
RGB connector on the back of the camera can be
selected.
@8Camera ID...

-42- nSETUP/INITIAL Set Memory Reset
The AW-E560 has a reset function, which restores the orig-
inal settings if the wrong data is set in SETUP or INITIAL
SET.
(1) Switch camera power off, and switch it back on.
(2) Complete the operation mode/scene file setting and
press the page switch. When the new settings for
reset are displayed, press the page switch again for
about 2 seconds while CURR: MODE 1/SCENE  1 is
displaying on the screen then the screen shown at
right on the top appears.
Note:Display...

NO.1    USER A     * 0DB
(.35-.55)     CURR NEW
*GAMMA(NOR)     .45 .45
*GAMMA(SHT)     .45 .45
KNEE POINT      98  98%
WHITE CLIP     110 110%
*H.DTL LEVEL H   31  31
*V.DTL LEVEL H   31  31
*H.DTL LEVEL L   15  15
*V.DTL LEVEL L   15  15
RET   END
NO.1    USER A     * 0DB
(.35-.55)     CURR NEW
*GAMMA(NOR)     .45 .45
*GAMMA(SHT)     .45 .45
KNEE POINT      98  98%
WHITE CLIP     110 110%
*H.DTL LEVEL H   31  31
*V.DTL LEVEL H   31  31
*H.DTL LEVEL L   15  15
*V.DTL LEVEL L   15  15
RET
-43-
USER SETUP...

-44-  
NO.2    USER A     * 0DB
(  2-  5)     CURR NEW
*DTL BAND         5   5
*NOISE SUP        1   1
*LEVEL DEP        0   0%
*CHROMA DTL       0   0
DARK DTL         0   0
RET   END
NO.3    USER A     * 0DB
(-25- 25)     CURR NEW
MATRIX(R-G)      0   0%
(R-B)      0   0%
(G-R)      0   0%
(G-B)      0   0%
(B-R)      0   0%
(B-G)      0   0%
FLARE RED        0   0
GREEN      0   0
BLUE       0   0
RETNO.2    USER A     * 0DB
(  2-  5)     CURR NEW
*DTL BAND         5   5
*NOISE SUP        1   1
*LEVEL...

-45- #0Gamma Compensation Level Setting
[GAMMA (NOR): .35 to .55]
[GAMMA (SHT): .35 to .55]
Gamma correction level can be set.
[GAMMA (NOR)] can be set when the electronic shut-
ter is OFF (normal state), or [GAMMA (SHT)] when it is
ON.
#1Knee Compensation Level Setting
[KNEE POINT: 88% to 98%]
The level of video signals subject to knee correction
(knee point) can be set.
#2White Clip Level Setting
[WHITE CLIP: 95% to 110%]
The peak level of video signals to be white-clipped
can be set. 
#3Horizontal...

-46- Note:
Dark detail setting is invalid unless level dependent
correction level [LEVEL DEP] is set to 0.
#9Matrix Compensation Level Setting
[MATRIX (R-G): -25% to 25%]
[MATRIX (R-B): -25% to 25%]
[MATRIX (G-R): -25% to 25%]
[MATRIX (G-B): -25% to 25%]
[MATRIX (B-R): -25% to 25%]
[MATRIX (B-G): -25% to 25%]
Matrix compensation level can be adjusted.
(R-G): To increase or decrease the intermediate
color between red and magenta
(R-B): To increase or decrease the intermediate
color between red and yellow...

(4) To return to the SETUP menu state, move the cursor to
RET and press the page switch.
(5) To change gain up, move the cursor to GAIN in the
SETUP menu, and use the Up or Down switch. (This
applies in cases where the camera is used alone.)
-47-(6) To return to the normal state, do the following steps.
If the camera is used alone, move the cursor to END,
and press the page switch.
If the camera is used with an RCU (RCB), set the user
set switch to OFF.
The camera will then operate according to the set-...

(4) Unless NO is selected by pressing the Down
(DOWN/BAR) switch within about 10 seconds after the
screen shown in Step (2) above appears, or unless
the Up (UP/ABC) switch or the Down (DOWN/BAR)
switch is pressed in 10 seconds or more after the
screen shown in Step (2) appears, the reset operation
is suspended as indicated by the screen at right, and
the operation returns to normal state.
-48-
NON RESET
CAMERA INSTALLATIONThe camera can be mounted using the mounting hole on
top or the one in the bottom...