Home
>
Panasonic
>
Network Hardware
>
Panasonic Central Processing Unit Wj Mpu955 Operating Instructions
Panasonic Central Processing Unit Wj Mpu955 Operating Instructions
Here you can view all the pages of manual Panasonic Central Processing Unit Wj Mpu955 Operating Instructions. The Panasonic manuals for Network Hardware are available online for free. You can easily download all the documents as PDF.
Page 31
31 Display Setting for Controller Adjustment of LCD Display The following procedures let you adjust backlight and con- trast of the controller’s LCD display. Back Light Adjustment Adjust the back light by turning the LCD BRIGHT control located on the rear of the controller. Clockwise:increases the back light brightness Counterclockwise:decreases the back light bright- ness Contrast Adjustment Adjust the contrast of the characters displayed on the LCD display by turning the LCD CONTRAST control located...
Page 32
32 Controlling Camera Site Accessories Controls for camera site accessories are located on the right side of the front panel of the System Controller. Included are Zoom Control, Focus Control, Iris Control, Preset and Pan/Tilt Controls. Normally, combination cam- eras equipped with the specific feature or a WV-RC100 or WV-RC150 Receiver are required to utilize these functions. Lens Control Note:Confirm that the specified lens, with power zoom/focus functions, is mounted on the camera. Also confirm that...
Page 33
![Page 33
33
Pan/Tilt Control
(Program Preset Position)
The following function requires the use of cameras
equipped with this specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Move the camera to the position to be preset by mov-
ing the Joystick Controller and pressing the lens control
keys.
3. Select the desired preset position number by pressing
the numeric keys.
4. Holding down the [PGM PRESET]key, and then press
the [CAMERA (ENTER)]key to save...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-32.png "Page 33
33
Pan/Tilt Control
(Program Preset Position)
The following function requires the use of cameras
equipped with this specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Move the camera to the position to be preset by mov-
ing the Joystick Controller and pressing the lens control
keys.
3. Select the desired preset position number by pressing
the numeric keys.
4. Holding down the [PGM PRESET]key, and then press
the [CAMERA (ENTER)]key to save...")
33 Pan/Tilt Control (Program Preset Position) The following function requires the use of cameras equipped with this specific feature. 1. Select the desired monitor and camera. Refer to the Monitor Selection and Camera Selection. 2. Move the camera to the position to be preset by mov- ing the Joystick Controller and pressing the lens control keys. 3. Select the desired preset position number by pressing the numeric keys. 4. Holding down the [PGM PRESET]key, and then press the [CAMERA (ENTER)]key to save...
Page 34
![Page 34
34
Receiver Control
Camera Housing Control
The following function is available only when the WV-RC100
or WV-RC150 Receivers are included in the system and the
specified camera housing is installed.
• Wiper Control
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera
Selection.
2. Pressing the [IRIS CLOSE]key while holding down
the [SHIFT]key will turn on the Housing Wiper of
the camera until the keys are released.
• Defroster Control
1. Select the desired monitor and...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-33.png "Page 34
34
Receiver Control
Camera Housing Control
The following function is available only when the WV-RC100
or WV-RC150 Receivers are included in the system and the
specified camera housing is installed.
• Wiper Control
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera
Selection.
2. Pressing the [IRIS CLOSE]key while holding down
the [SHIFT]key will turn on the Housing Wiper of
the camera until the keys are released.
• Defroster Control
1. Select the desired monitor and...")
34 Receiver Control Camera Housing Control The following function is available only when the WV-RC100 or WV-RC150 Receivers are included in the system and the specified camera housing is installed. • Wiper Control 1. Select the desired monitor and camera. Refer to the Monitor Selection and Camera Selection. 2. Pressing the [IRIS CLOSE]key while holding down the [SHIFT]key will turn on the Housing Wiper of the camera until the keys are released. • Defroster Control 1. Select the desired monitor and...
Page 35
![Page 35
35
Camera Function Control
Camera Setup
The following function requires the use of cameras
equipped with this specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Pressing the [F4]key while holding down the [SHIFT]
key will gain access to the Camera Setup Menu display
on the active monitor.
3. Select the desired item in the menu by moving the
Joystick Controller UPand DOWN, and then select the
desired parameter (or mode) in the menu by...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-34.png "Page 35
35
Camera Function Control
Camera Setup
The following function requires the use of cameras
equipped with this specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Pressing the [F4]key while holding down the [SHIFT]
key will gain access to the Camera Setup Menu display
on the active monitor.
3. Select the desired item in the menu by moving the
Joystick Controller UPand DOWN, and then select the
desired parameter (or mode) in the menu by...")
35 Camera Function Control Camera Setup The following function requires the use of cameras equipped with this specific feature. 1. Select the desired monitor and camera. Refer to the Monitor Selection and Camera Selection. 2. Pressing the [F4]key while holding down the [SHIFT] key will gain access to the Camera Setup Menu display on the active monitor. 3. Select the desired item in the menu by moving the Joystick Controller UPand DOWN, and then select the desired parameter (or mode) in the menu by...
Page 36
![Page 36
36
Patrol Learn and Play
The following function requires the use of cameras
equipped with this specific feature.
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Press the [F6]key three times.
Patrol Learn as shown in the figure will appear on the
LCD display of the controller.
To save the patrol sequence, follow the procedure
shown below.
qPress the...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-35.png "Page 36
36
Patrol Learn and Play
The following function requires the use of cameras
equipped with this specific feature.
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Press the [F6]key three times.
Patrol Learn as shown in the figure will appear on the
LCD display of the controller.
To save the patrol sequence, follow the procedure
shown below.
qPress the...")
36 Patrol Learn and Play The following function requires the use of cameras equipped with this specific feature. A routine of manual operations can be stored for a specific time and later reproduced repetitively. 1. Select the desired monitor and camera. Refer to the Monitor Selection and Camera Selection. 2. Press the [F6]key three times. Patrol Learn as shown in the figure will appear on the LCD display of the controller. To save the patrol sequence, follow the procedure shown below. qPress the...
Page 37
![Page 37
37
Running Sequence
Tour Sequence
The following functions are available only if a Tour
Sequence has been previously established through the
Administration Console. As described on the setup, any of
the tours can be assigned to any of the monitors.
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Select the desired Tour Sequence Number by pressing
the numeric keys.
3. Pressing the [FWD RUN]key while holding down the
[TOUR SEQ]key will run the tour sequence in forward
direction on the...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-36.png "Page 37
37
Running Sequence
Tour Sequence
The following functions are available only if a Tour
Sequence has been previously established through the
Administration Console. As described on the setup, any of
the tours can be assigned to any of the monitors.
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Select the desired Tour Sequence Number by pressing
the numeric keys.
3. Pressing the [FWD RUN]key while holding down the
[TOUR SEQ]key will run the tour sequence in forward
direction on the...")
37 Running Sequence Tour Sequence The following functions are available only if a Tour Sequence has been previously established through the Administration Console. As described on the setup, any of the tours can be assigned to any of the monitors. 1. Select the desired monitor. Refer to the Monitor Selection. 2. Select the desired Tour Sequence Number by pressing the numeric keys. 3. Pressing the [FWD RUN]key while holding down the [TOUR SEQ]key will run the tour sequence in forward direction on the...
Page 38
![Page 38
38
On-Screen Display Control
The procedure described below lets you determine the dis-
play, such as camera title, clock and status, on and off on
the active monitor screen.
Note:The following functions are not available when the
on-screen displays are compounded from the
Character Board that is installed on the Camera Input
Board. Confirm the setting in the Administration
Console for details.
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Pressing the [1]key while holding down the...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-37.png "Page 38
38
On-Screen Display Control
The procedure described below lets you determine the dis-
play, such as camera title, clock and status, on and off on
the active monitor screen.
Note:The following functions are not available when the
on-screen displays are compounded from the
Character Board that is installed on the Camera Input
Board. Confirm the setting in the Administration
Console for details.
1. Select the desired monitor.
Refer to the Monitor Selection.
2. Pressing the [1]key while holding down the...")
38 On-Screen Display Control The procedure described below lets you determine the dis- play, such as camera title, clock and status, on and off on the active monitor screen. Note:The following functions are not available when the on-screen displays are compounded from the Character Board that is installed on the Camera Input Board. Confirm the setting in the Administration Console for details. 1. Select the desired monitor. Refer to the Monitor Selection. 2. Pressing the [1]key while holding down the...
Page 39
![Page 39
39
5. Pressing the [5]key while holding down the [OSD]key
will toggle the monitor status display on the active mon-
itor on and off.
6. Pressing the [6]key while holding down the [OSD]key
will toggle the display except clock (time and date) on
the active monitor on and off.
07/07/1999 03:37:21 PM
M AREA1 ALM T R A
C CAMERA TITLE
CAM ID
VLD S T&D
ALM SGEN
SYS S
(
ALARM)
0 8 7
MSTATUS
VLD HALL
ALM H
BLK5
9 6 423 1
SHIFTCLEAR
(
ESC)
EXIT
GROUP
PRESETPREVS-CTL ID OPE IDNEXT
GROUP...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-38.png "Page 39
39
5. Pressing the [5]key while holding down the [OSD]key
will toggle the monitor status display on the active mon-
itor on and off.
6. Pressing the [6]key while holding down the [OSD]key
will toggle the display except clock (time and date) on
the active monitor on and off.
07/07/1999 03:37:21 PM
M AREA1 ALM T R A
C CAMERA TITLE
CAM ID
VLD S T&D
ALM SGEN
SYS S
(
ALARM)
0 8 7
MSTATUS
VLD HALL
ALM H
BLK5
9 6 423 1
SHIFTCLEAR
(
ESC)
EXIT
GROUP
PRESETPREVS-CTL ID OPE IDNEXT
GROUP...")
39 5. Pressing the [5]key while holding down the [OSD]key will toggle the monitor status display on the active mon- itor on and off. 6. Pressing the [6]key while holding down the [OSD]key will toggle the display except clock (time and date) on the active monitor on and off. 07/07/1999 03:37:21 PM M AREA1 ALM T R A C CAMERA TITLE CAM ID VLD S T&D ALM SGEN SYS S ( ALARM) 0 8 7 MSTATUS VLD HALL ALM H BLK5 9 6 423 1 SHIFTCLEAR ( ESC) EXIT GROUP PRESETPREVS-CTL ID OPE IDNEXT GROUP...
Page 40
![Page 40
40
Alarm Control
When cameras and monitor are armed for alarm response
with an alarm input, the camera pictures associated with
that alarm input is displayed on the monitor when the alarm
is received.
When an alarm is received, the ALARM indicator lights. The
indicator remains lit until all alarms are cleared by pressing
the RESET key.
Alarm Arming Control
1. Select an alarm number by pressing the numeric keys,
followed by the [ALARM]key.
2. Pressing the [ARM]key repeatedly will arm or disarm
cameras...](http://img.usermanuals.tech/thumb/58/69467/w300_wj-mpu955_en_om_d-39.png "Page 40
40
Alarm Control
When cameras and monitor are armed for alarm response
with an alarm input, the camera pictures associated with
that alarm input is displayed on the monitor when the alarm
is received.
When an alarm is received, the ALARM indicator lights. The
indicator remains lit until all alarms are cleared by pressing
the RESET key.
Alarm Arming Control
1. Select an alarm number by pressing the numeric keys,
followed by the [ALARM]key.
2. Pressing the [ARM]key repeatedly will arm or disarm
cameras...")
40 Alarm Control When cameras and monitor are armed for alarm response with an alarm input, the camera pictures associated with that alarm input is displayed on the monitor when the alarm is received. When an alarm is received, the ALARM indicator lights. The indicator remains lit until all alarms are cleared by pressing the RESET key. Alarm Arming Control 1. Select an alarm number by pressing the numeric keys, followed by the [ALARM]key. 2. Pressing the [ARM]key repeatedly will arm or disarm cameras...