Panasonic Camera Recorder Ajhdx900 Operating Instructions

51
4
Chapter 4  Adjustments and settings for recording(continued)
Display item What is displayed Status when display appears
1System mode
1080
720 This indicates the mode that the unit operates in.
1080 interlace mode
720 progressive mode
2
Camera mode
60i
30P
24P
24PA
50i
25P
60P
50P This indicates the video systems for recording signals output from the
CCD on tape and outputting signals as HD SDI signals.
1080-59.94i
1080-29.97P or 720-29.97P
1080-23.98P or 720-23.98P (2-3 Pull-down)
1080-23.98P...

52
This appears when the position of the WHITE BAL switch has been
changed.  “A, ” “ B ” or  “PRE ” appears at #.
This appears when the AUTO KNEE switch has been set to ON or OFF.
This appears when the gain has been selected using the GAIN
selector switch or USER button.
This indicates the shutter speed value when the shutter speed has
been selected.
This appears when synchro scan has been selected as the shutter
speed.
This appears when the CC filter setting has been selected.
This appears when the ND...

53
4
Chapter 4  Adjustments and settings for recording(continued)
Display item What is displayed Status when display appears
\fInformation
allocated to USER
buttons
UM: USER MAIN
U1: USER1 button
U2: USER2 button INH
S.GAIN  
¢¢dB/OFF
DS.GAIN   ¢¢:/OFF
LINE MIX ON/OFF
S.IRIS  ON/OFF
I.OVR  ON/OFF
S.BLK   –¢¢ /OFF
B.GAMMA ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
Y GET ON
RET SW
DRS “
INH ” is indicated when the operation of the USER button has been
disabled.
This indicates the value selected for S.GAIN.
This...

54
Chapter 4  Adjustments and settings for recording(continued)
Display item What is displayed Status when display appears
EAUDIO input
system and level
meter This indicates the audio channels selected and their audio levels.
This appears when the AUDIO IN switch is at the FRONT position.
This appears when the AUDIO IN switch is at the WIRELESS position.
This appears when the AUDIO IN switch is at the REAR position.

---- ---+\b
F
W
R
F Super black ON B This appears when S.BLK has been set to ON.
G...

55
4
Chapter 4  Adjustments and settings for recording(continued)
Whether a display isto be shown or not
can be selected on a menu. Status displayed
when established Displayed only by
MODE CHECK button (*1) Display can be
cleared Displayed during
playback
1 Systetm mode ≤—
µ≤ —
2 
Camera mode ≤
—µ≤
—
3 Shutter speed/mode
≤≤µ≤ —
4  Total length of cassette tape
——µ≤
—
5 Remaining tape ≤—
µ≤ —
6 
Unit’s REC display ≤≤µ≤ —
\b 
Battery type ——
µ≤—
9 
MODE CHECK dedicated display area ——
≤≤—
8 
Remaining...

56
#< \bF MARKER >MKR:A
TABLE          :A
CENTER MARK    :1
SAFETY ZONE    :2
SAFETY AREA    :90%
FRAME SIG      :4:\f
FRAME MARK     :OFF
FLAME L\bL      :15

#< CAMERA ID >
ID1 : ABCDEFGHIJ
ID2 : ABCDEFGHIJ
ID\f : ABCDEFGHIJ

4-7-6 Setting the camera ID
The camera ID is set on the CAMERA ID screen.
Up to ten alphanumerics, symbols and spaces can be used.

The camera ID is not displayed while the setting menu is
displayed even if color bar signals are output.
4-7-5 Setting the marker displays
ON, OFF...

57
4
4-7-7 Mode check screen displays (MODE
CHECK button function)
The screens enabling the unit ’s settings and modes to be
checked can be displayed in the viewfinder.
Each time the unit ’s MODE CHECK button is pressed, one of
the four screen displays is selected in the following
sequence: STATUS screen display 
>!LED screen display
>FUNCTION screen display >AUDIO screen display.
Each screen is displayed for about 3 seconds.
When the MODE CHECK button is pressed and held, the
screen is displayed...

58
Chapter 4  Adjustments and settings for recording(continued)
4-8 Selection of video output signals
The unit employs the VIDEO OUT connector and the MON
OUT connector as connectors for outputting video signals.
4-8-1 Settings of signals output fromVIDEO OUT connector
The signal modes for outputting signals from the VIDEO
OUT connector are switched with the VIDEO OUT switch.
HD SDI: To output the HD SDI signals
SD SDI: To output the down-converted SD SDI signals
VBS: To output the down-converted...

59
4
Chapter 4  Adjustments and settings for recording(continued)
Set the marker and user boxes to superimpose on the output
signals from the VIDEO OUT connector by using the
respective items on the  screen
(SYSTEM SETTING page) of the menu.
USER BOX WIDTH 1: 13: 100
For setting the horizontal width of the user
box.
USER BOX
HEIGHT1: 13: 100
For setting the vertical height of the user
box.
USER BOX H POS
–50: +00: +50
For setting the horizontal position of the user
box center.
USER BOX V POS –50: +00:...

60
Chapter 4  Adjustments and settings for recording(continued)
Switch the signals output from the MON OUT connector by
using MONI OUT MODE item on the menu (
screen on the SYSTEM SETTING page).
4-8-2 Settings of signals output from MONOUT connector
Set the video signals output from the MON OUT connector
by using the MONI OUT item on the menu (
screen on the SYSTEM SETTING page).
The HD-Y signals can be used for applying GEN LOCK to
other devices. It is impossible to superimpose markers and
characters...