Panasonic Aj Sdx900 Operating Instructions Manual

81
7
Chapter 7  Menu description tables
Mg (SAT/PHASE)–63: +00: +63
For performing the magenta color correction
(saturation and hue).
R (SAT/PHASE)–63: +00: +63
For performing the red color correction
(saturation and hue).
R-Mg (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between red and magenta.
Mg-B (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between magenta and blue.
7-3-3 COLOR CORRECTION
ItemVariable
rangeRemarks
Cy...

82
Chapter 7  Menu description tables
7-3-5 MID SETTING
MATRIX TABLE OFFA
BFor selecting the color correction table.
COLOR CORRECT ONOFFFor selecting ON or OFF for the color
correction. ItemVariable
rangeRemarks
MASTER GAIN–3dB: 9dB: 30dB
For setting the master gain to –3, 0, 3, 6, 9,
12, 15, 18, 21, 24, 27 or 30 dB.
H.DTL LEVEL 00: 20: 63
For performing the H.DTL LEVEL setting.
V.DTL LEVEL 00: 10: 31
For performing the V.DTL LEVEL setting.
DTL CORING 00: 03: 15
For performing the DTL CORING setting....

83
7
Chapter 7  Menu description tables
7-3-7 ADDITIONAL DTL
ItemVariable
rangeRemarks
KNEE APE LVL OFF
1
2: 5
For performing the KNEE APE LEVEL setting.
CHROMA DTLOFF
0
: 5
For performing the CHROMA DTL setting.
The chroma edge is detected and placed on
the Y signal to bolster H.DTL.  The higher the
number, the greater the correction.
DTL GAIN(+)–31: +00: +31
For changing the H.DTL “+” direction level.
DTL GAIN(–)–31: +10: +31
For changing the H.DTL “–” (down) direction
level.
DTL CLIP00: 63
For...

84
Chapter 7  Menu description tables
7-3-9 KNEE/LEVEL
ItemVariable
rangeRemarks
MASTER PED–200: +000: +200
For performing the MASTER PEDESTAL
setting.
MANUAL KNEEON
OFFFor setting the mode which is to be established
when the AUTO KNEE switch is at OFF.  The
KNEE POINT/SLOPE setting value is active
when ON is selected.
KNEE POINT 70.0%: 85.0%: 107.0%
For setting the KNEE POINT position in 0.5%
steps.
KNEE SLOPE 00: 50: 99 (98)
For performing the KNEE width setting.
Same as KNEE OFF when set to 0.

The...

85
7
Chapter 7  Menu description tables
ItemVariable
rangeRemarks
DETAILON
OFFFor selecting ON or OFF for DTL (H, V).
2D LPF ONOFFFor selecting ON or OFF for the 2-
dimensional LPF that reduces cross color.
HIGH COLOR ONOFFFor selecting ON or OFF for the mode in
which the dynamic range of the colors is
expanded.
TEST SAW ONOFFFor selecting ON or OFF for the test signals.
GAMMAON
OFFFor selecting ON or OFF for the gamma
circuit.
FLAREON
OFFFor selecting ON or OFF for the flare
compensation.
H-F COMPE.ON...

86
Chapter 7  Menu description tables
7-4-2 VF MARKER
ItemVariable
rangeRemarks
TABLEA
BFor selecting the VF MARKER setting table.
This item is used to set the current values of
table A or B which have been selected using
the menu items listed below.
CENTER MARK OFF1
2
3
4For selecting the center marker.
OFF:The center marker is not displayed.
1:+ (large)
2:Center blank (large)
3:+ (small)
4:Center blank (small)
SAFETY ZONE OFF
1
2
For selecting the type of safety zone frame.
OFF:The safety zone frame is...

87
7
Chapter 7  Menu description tables
D.ZOOM ONOFFFor selecting whether or not the display is to
come on during digital zoom operations.
7-4-5 VF INDICATOR2
ItemVariable
rangeRemarks
TAPEON
OFFFor selecting ON or OFF for the remaining
tape amount display.
BATTERYON
OFFFor selecting ON or OFF for the battery
voltage display.
AUDIO LVLON
OFFFor selecting ON or OFF for the audio level
meter display.
TC TCG
TCR
TCG/TCR
OFF
For selecting the time code which is to be
displayed.
TCG:The time code generator...

88
Chapter 7  Menu description tables
7-5-2 SHUTTER SPEED
ItemVariable
rangeRemarks
SYNCHRO SCANON
OFFFor selecting SYNCHRO SCAN as the shutter
speed to be used.
SUPER V ONOFFFor selecting SUPER V as the shutter speed
to be used.
POSITION1ON
OFFFor selecting POSITION1 as the shutter
speed to be used.
POSITION2ON
OFFFor selecting POSITION2 as the shutter
speed to be used.
POSITION3ON
OFFFor selecting POSITION3 as the shutter
speed to be used.
POSITION4ON
OFFFor selecting POSITION4 as the shutter
speed to...

89
7
Chapter 7  Menu description tables
7-5-4 USER SW
ItemVariable
rangeRemarks
USER MAIN SW INHS.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AUDIO CH1
AUDIO CH2
REC SW
Y GET
RET SW
ATW
D.ZOOMFor allocating the USER MAIN switch
function.
USER1 SWINH
S.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AUDIO CH1
AUDIO CH2
REC SW
Y GET
RET SW
ATW
D.ZOOM
For allocating the USER1 switch function.
USER2 SW INH
S.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AUDIO CH1
AUDIO CH2
REC SW
Y GET
RET SW
ATW
D.ZOOM
For allocating the USER2...

90
Chapter 7  Menu description tables
7-5-6 WHITE BALANCE MODE
AWB BMEM
ATW
VARFor selecting the allocation of the WHITE BAL
switch position and Bch.
MEM:The switch position and Bch are
allocated as memory values when
AWB is executed.
ATW:The position and Bch are allocated as
ATW start switch functions.
VAR:The color temperature of B can be set
to vary using the COLOR TEMP B
menu item.
COLOR TEMP B3200K: 5600K
For setting the color temperature when AWB
B has been set to VAR.
ItemVariable
rangeRemarks...