Panasonic Aj Sdx900 Operating Instructions Manual

							81
7
Chapter 7  Menu description tables
Mg (SAT/PHASE)–63: +00: +63
For performing the magenta color correction
(saturation and hue).
R (SAT/PHASE)–63: +00: +63
For performing the red color correction
(saturation and hue).
R-Mg (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between red and magenta.
Mg-B (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between magenta and blue.
7-3-3 COLOR CORRECTION
ItemVariable
rangeRemarks
Cy (SAT/PHASE)–63: +00: +63
For performing the cyan color correction
(saturation and hue).
Cy-G (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between cyan and green.
G (SAT/PHASE)–63: +00: +63
For performing the green color correction
(saturation and hue).
G-Yl (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between green and yellow.
Yl (SAT/PHASE)–63: +00: +63
For performing the yellow color correction
(saturation and hue).
Yl-R (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between yellow and red.
B-Cy (SAT/PHASE)–63: +00: +63
For performing the color correction (saturation
and hue) between blue and cyan.
B (SAT/PHASE)–63: +00: +63
For performing the blue color correction
(saturation and hue).
7-3-4 LOW SETTING
MATRIX TABLE OFFA
BFor selecting the color correction table.
COLOR CORRECT ONOFFFor selecting ON or OFF for the color
correction. ItemVariable
rangeRemarks
MASTER GAIN–3dB: 0dB: 30dB
For setting the master gain to –3, 0, 3, 6, 9,
12, 15, 18, 21, 24, 27 or 30 dB.
H.DTL LEVEL 00: 28: 63
For performing the H.DTL LEVEL setting.
V.DTL LEVEL 00: 12: 31
For performing the V.DTL LEVEL setting.
DTL CORING 00: 02: 15
For performing the DTL CORING setting.
H.DTL FREQ. 00: 20: 31
For performing the H.DTL FREQ setting.
LEVEL DEPEND. 01: 5
For performing the LEVEL DEPEND setting.
MASTER GAMMA 0.35: 0.45: 0.75
For setting the MASTER GAMMA in 0.01
steps.
BLACK STRECH–3: OFF: +3
For setting the gamma curve of the dark
areas.
The underlining in the variable range column indicates the setting in the preset mode. The underlining in the variable range column indicates the setting in the preset mode. 
						

							82
Chapter 7  Menu description tables
7-3-5 MID SETTING
MATRIX TABLE OFFA
BFor selecting the color correction table.
COLOR CORRECT ONOFFFor selecting ON or OFF for the color
correction. ItemVariable
rangeRemarks
MASTER GAIN–3dB: 9dB: 30dB
For setting the master gain to –3, 0, 3, 6, 9,
12, 15, 18, 21, 24, 27 or 30 dB.
H.DTL LEVEL 00: 20: 63
For performing the H.DTL LEVEL setting.
V.DTL LEVEL 00: 10: 31
For performing the V.DTL LEVEL setting.
DTL CORING 00: 03: 15
For performing the DTL CORING setting.
H.DTL FREQ. 00: 20: 31
For performing the H.DTL FREQ setting.
LEVEL DEPEND. 01: 5
For performing the LEVEL DEPEND setting.
MASTER GAMMA 0.35: 0.45: 0.75
For setting the MASTER GAMMA in 0.01
steps.
BLACK STRECH–3: OFF: +3
For setting the gamma curve of the dark
areas.
7-3-6 HIGH SETTING
MATRIX TABLE OFFA
BFor selecting the color correction table.
COLOR CORRECT ONOFFFor selecting ON or OFF for the color
correction. ItemVariable
rangeRemarks
MASTER GAIN–3dB: 18dB: 30dB
For setting the master gain to –3, 0, 3, 6, 9,
12, 15, 18, 21, 24, 27 or 30 dB.
H.DTL LEVEL 00: 10: 63
For performing the H.DTL LEVEL setting.
V.DTL LEVEL 00: 10: 31
For performing the V.DTL LEVEL setting.
DTL CORING 00: 08: 15
For performing the DTL CORING setting.
H.DTL FREQ. 00: 20: 31
For performing the H.DTL FREQ setting.
LEVEL DEPEND. 0: 3: 5
For performing the LEVEL DEPEND setting.
MASTER GAMMA 0.35: 0.55: 0.75
For setting the MASTER GAMMA in 0.01
steps.
BLACK STRECH–3: OFF: +3
For setting the gamma curve of the dark
areas.
The underlining in the variable range column indicates the setting in the preset mode. 
						

							83
7
Chapter 7  Menu description tables
7-3-7 ADDITIONAL DTL
ItemVariable
rangeRemarks
KNEE APE LVL OFF
1
2: 5
For performing the KNEE APE LEVEL setting.
CHROMA DTLOFF
0
: 5
For performing the CHROMA DTL setting.
The chroma edge is detected and placed on
the Y signal to bolster H.DTL.  The higher the
number, the greater the correction.
DTL GAIN(+)–31: +00: +31
For changing the H.DTL “+” direction level.
DTL GAIN(–)–31: +10: +31
For changing the H.DTL “–” (down) direction
level.
DTL CLIP00: 63
For changing the DTL signal “+” direction clip.
DTL SOURCE(R+G)/2
(G+B)/2
2G+R+B /4
(3G+R)/4
R
GFor setting the signal source of the DTL signal
components.
H.DTL LINE MIX 0H1H
2HFor setting the scanning lines for generating
the H.DTL signal.
CORNER DTLON
OFFFor selecting ON or OFF for the mode in
which the resolution is improved in the
corners of the screen.
7-3-8 SKIN TONE DTL
ItemVariable
rangeRemarks
SKIN TONE DTL ONOFFFor selecting ON or OFF for the skin tone
DTL.
SKIN TONE ZEBRA ONOFFFor selecting ON or OFF for ZEBRA in the
SKIN TONE range.
SKIN DTL CORING 0: 5: 7
For setting the SKIN TONE DTL coring effect.
Y MAX 000: 190: 255
For setting the maximum luminance signal
value for applying the SKIN TONE effect.
Y MIN 000: 010: 255
For setting the minimum luminance signal
value for applying the SKIN TONE effect.
I CENTER 000: 030: 255
For setting the center position on the I axis
(setting the area to which the SKIN TONE
effect is to be applied).
I WIDTH 000: 035: 255
For setting the width of the area to which the
SKIN TONE effect is to be applied on the I
axis centered on the I CENTER.
Q WIDTH 000: 010: 255
For setting the width of the area to which the
SKIN TONE effect is to be applied on the Q
axis centered on the I CENTER.
Q PHASE–31: +00: +31
For setting the phase of the area to which the
SKIN TONE effect is to be applied as
referenced to the Q axis.
R-Y
B-Y
Q-WIDTHI-WIDTH
Q-PHASE I-CENTER
Y
Y-MAX
Y-MIN
0=SKIN TONE AREA – direction+ direction
The underlining in the variable range column indicates the setting in the preset mode. 
						

							84
Chapter 7  Menu description tables
7-3-9 KNEE/LEVEL
ItemVariable
rangeRemarks
MASTER PED–200: +000: +200
For performing the MASTER PEDESTAL
setting.
MANUAL KNEEON
OFFFor setting the mode which is to be established
when the AUTO KNEE switch is at OFF.  The
KNEE POINT/SLOPE setting value is active
when ON is selected.
KNEE POINT 70.0%: 85.0%: 107.0%
For setting the KNEE POINT position in 0.5%
steps.
KNEE SLOPE 00: 50: 99 (98)
For performing the KNEE width setting.
Same as KNEE OFF when set to 0.

The range of values that can be selected
using the AJ-EC3P is 00 to 98.
WHITE CLIP LVL 90%: 105%: 109%
For performing the WHITE CLIP LEVEL
setting.
A.KNEE POINT 80%: 85%: 107%
For setting the AUTO KNEE POINT position
in 0.5% steps.  This item is active when the
OUTPUT/AUTO KNEE selector switch is set
to CAM.AUTO KNEE ON.
A.KNEE LVL 100: 105: 109
For performing the AUTO KNEE level setting.
A.KNEE
RESPONSE1: 4
For setting the AUTO KNEE response speed.
WHITE CLIPON
OFFFor selecting ON or OFF for the WHITE CLIP
function.  The WHITE CLIP LVL setting value
is active when ON is selected.
7-3-11 FLARE
ItemVariable
rangeRemarks
R FLARE 000: 100
For performing the R FLARE setting.
G FLARE 000: 100
For performing the G FLARE setting.
B FLARE 000: 100
For performing the B FLARE setting.
7-3-10 GAMMA
ItemVariable
rangeRemarks
MASTER GAMMA 0.35: 0.45: 0.75
For setting the MASTER GAMMA in 0.01
steps.
R GAMMA–15: +00: +15
For setting the R channel GAMMA.
B GAMMA–15: +00: +15
For setting the B channel GAMMA.
GAMMA MODE
SELSTDFILM LIKE1
FILM LIKE2For selecting the GAMMA.
STD:The standard video gamma
characteristics are selected.FILM LIKE1:The cinema gamma characteristics
for video applications are selected.
At the factory, this setting is set in
scene file 4.
FILM LIKE2:The cinema gamma characteristics
for video applications are selected.
In this setting gradations in highlit
areas can be expressed better
than when FILM LIKE1 is selected.

Some of the KNEE SLOPE setting values in
the “7-3-9 KNEE/LEVEL” menu have no effect
if film-like characteristics are selected for the
GAMMA MODE SEL item.
The underlining in the variable range column indicates the setting in the preset mode. 
						

							85
7
Chapter 7  Menu description tables
ItemVariable
rangeRemarks
DETAILON
OFFFor selecting ON or OFF for DTL (H, V).
2D LPF ONOFFFor selecting ON or OFF for the 2-
dimensional LPF that reduces cross color.
HIGH COLOR ONOFFFor selecting ON or OFF for the mode in
which the dynamic range of the colors is
expanded.
TEST SAW ONOFFFor selecting ON or OFF for the test signals.
GAMMAON
OFFFor selecting ON or OFF for the gamma
circuit.
FLAREON
OFFFor selecting ON or OFF for the flare
compensation.
H-F COMPE.ON
OFFFor selecting ON or OFF for the mode in
which the wide-band DTL is increased.
7-3-12 CAMERA SETTINGS
ECU MENU DISP. ONOFFFor selecting ON or OFF for displaying the
MENU on the viewfinder when the ECU is
connected.
50M INDICATOR ONOFFFor selecting ON or OFF for the displays
during 50M recording.
7-4 VF
7-4-1 VF DISPLAYS
ItemVariable
rangeRemarks
DISP CONDITIONNORMAL
HOLDNORMAL:The statuses are displayed at all
times.
HOLD:The statuses are displayed only
when the MODE CHECK switch is
pressed.
DISP MODE 1
2
3
For performing the DISP MODE setting.  This
item is used to select the camera’s warning or
message displays.  For details, refer to “4-7-4
Display modes and setting changes/
adjustment result messages.”
VF OUTY
NAM
R
G
BFor selecting the VF output.
Y:Luminance signal
NAM:The signal with the highest level among
the R, G and B signals is output.
R:R channel signal
G:G channel signal
B:B channel signal
VF DTL 0: 3: 5
For performing the VF DTL selection.  This
item is used to further emphasize the DTL of
the VF signals.  If 0 is set, the DTL will be the
same as that of the main line signals.
ZEBRA1 DETECT 0%: 70%: 109%
For setting the ZEBRA1 detection level (IRE
level).
ZEBRA2 DETECT 0%: 85%: 109%
For setting the ZEBRA2 detection level (IRE
level).
ZEBRA2 ONSPOT
OFFFor selecting ON or OFF for ZEBRA2 or
selecting SPOT.
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35%
For setting how much lower the camera’s
input light quantity should be in order for
“LOW LIGHT” to be displayed.
MARKER/
CHAR LVL50%
60%
70%
80%
90%
100%For setting the brightness of the markers and
characters displayed in the viewfinder.
Zebra pattern display
Video levelSPOT OFF ON
109%
0% ZEBRA 2
DETECTZEBRA 2
ZEBRA 1
DETECT
The underlining in the variable range column indicates the setting in the preset mode. 
						

							86
Chapter 7  Menu description tables
7-4-2 VF MARKER
ItemVariable
rangeRemarks
TABLEA
BFor selecting the VF MARKER setting table.
This item is used to set the current values of
table A or B which have been selected using
the menu items listed below.
CENTER MARK OFF1
2
3
4For selecting the center marker.
OFF:The center marker is not displayed.
1:+ (large)
2:Center blank (large)
3:+ (small)
4:Center blank (small)
SAFETY ZONE OFF
1
2
For selecting the type of safety zone frame.
OFF:The safety zone frame is not displayed.
1:Box
2:Corner frames
SAFETY AREA 80%: 90%: 100%
For setting the position of the safety zone.
FRAME SIG4:3
13:9
14:9
VISTAFor setting the frame marker.
Note that this setting takes effect only when
REC MODE is set to 16:9.
The VISTA setting is 16:8.65.
FRAME MARK ONOFFFor selecting ON or OFF for the frame
marker.
FRAME LVL 00: 15
For setting the level of the frame marker.
0:Equivalent to signal OFF
15:Same brightness as center area
However, this setting has no effect if
FRAME SIG is set to VISTA.
USER BOX ONOFFFor setting whether or not to display the user
box.
7-4-3 USER BOX
ItemVariable
rangeRemarks
USER BOX WIDTH 001: 013: 100
For setting the horizontal width of the user
box.
USER BOX
HEIGHT001: 013: 121
For setting the vertical height of the user box.
USER BOX H POS–50: +00: +50
For setting the horizontal position of the user
box center.
USER BOX V POS–121: +000: +121
For setting the vertical position of the user box
center.
7-4-4 VF INDICATOR1
ItemVariable
rangeRemarks
EXTENDERON
OFFFor selecting ON or OFF for the extender
display.
SHUTTERON
OFFFor selecting ON or OFF for the shutter speed
display.
FILTERON
OFFFor selecting ON or OFF for the filter No.
display.
WHITEON
OFFFor selecting ON or OFF for the AWB
PRE/A/B display.
GAINON
OFFFor selecting ON or OFF for the currently
selected gain, S.GAIN and DS.GAIN display.
IRIS OFF
IRIS
S+IRIS
S
OFF:Neither the super iris ON status nor
the aperture value is displayed.
IRIS:Only the aperture value is displayed.
S+IRIS:Both the super iris ON status and
aperture value are displayed.
S:The super iris ON status is displayed.
(The display or non-display of the aperture
value and that of the iris override are linked.)
CAMERA IDBAR
CAM
ALWAYS
OFFFor setting the ID configuration during
recording.
BAR:The ID is recorded when color bar
signals are provided.
CAM:The ID is recorded when the camera
images are provided.
ALWAYS:The ID is recorded at all times.
OFF:The ID is not recorded at any time.
ID POSITION UPPER RUPPER L
LOWER R
LOWER LFor setting the location where the camera ID
is to be recorded.
UPPER R:Top right
UPPER L:Top left
LOWER R:Bottom right
LOWER L:Bottom left 
ZOOM LVLON
OFFFor selecting ON or OFF for the zoom
position display.
COLOR TEMPON
OFFFor selecting ON or OFF for the color
temperature display.
CAMERA MODEON
OFFFor selecting ON or OFF for the camera’s
operation mode display.
DATE/TIME ONOFFFor specifying whether or not the date and
time are mixed simultaneously when the
CAMERA ID is recorded.
The underlining in the variable range column indicates the setting in the preset mode. 
						

							87
7
Chapter 7  Menu description tables
D.ZOOM ONOFFFor selecting whether or not the display is to
come on during digital zoom operations.
7-4-5 VF INDICATOR2
ItemVariable
rangeRemarks
TAPEON
OFFFor selecting ON or OFF for the remaining
tape amount display.
BATTERYON
OFFFor selecting ON or OFF for the battery
voltage display.
AUDIO LVLON
OFFFor selecting ON or OFF for the audio level
meter display.
TC TCG
TCR
TCG/TCR
OFF
For selecting the time code which is to be
displayed.
TCG:The time code generator value is
displayed in the E-E mode.
TCR:The time code reader value is
displayed in the V-V mode.
TCG/TCR:The time code generator value is
displayed in the E-E mode, and the
time code reader value is displayed
in the V-V mode.
OFF:The time code is not displayed at
any time.
VTR WARNING ALWAYSNORMAL
OFFFor selecting how VTR warnings are
displayed.
ALWAYS:It is displayed every time a warning
has occurred.
NORMAL:It is displayed for 3 seconds when a
warning has occurred and also for 3
seconds after recording has started
and after recording has finished.
OFF:It is not displayed at any time.
SAVE LED SAVE&
TAPE
SAVE
For setting the operation of the SAVE lamp.
SAVE&TAPE:
The lamp lights up when the VTR
SAVE/STBY switch has been set to the
SAVE position.  It is off during recording.
As the tape is approaching the end, it
starts flashing in tandem with the warning
alarm.
SAVE:The lamp lights up when the VTR
SAVE/STBY switch has been set to
the SAVE position.  It is off during
recording.
STATUSON
OFFFor setting whether or not to display the status
when the MODE CHECK switch is used.
7-4-6 MODE CHECK IND
ItemVariable
rangeRemarks
!LEDON
OFFFor setting whether or not to display the
cause display screen if the !LED has lighted
when the MODE CHECK switch is used.
FUNCTIONON
OFFFor setting whether or not to display the
function display screen when the MODE
CHECK switch is used.
AUDIOON
OFFFor setting whether or not to display the audio
display screen when the MODE CHECK
switch is used.
P.ON INDON
OFFFor setting whether or not to display the
status display screen after the power has
been turned on.
ATW ONOFFFor selecting whether or not the display is to
come on when ATW is ON.
7-4-7 !LED
ItemVariable
rangeRemarks
GAIN(0dB)ON
OFFFor selecting whether or not the display is to
come on when the gain is other than 0 dB.
GAIN (–3dB) ONOFFFor selecting whether or not the display is to
come on when the gain is other than –3 dB.
DS.GAIN ONOFFFor selecting whether or not the display is to
come on when the DS.GAIN (cumulative gain)
has been entered.
SHUTTERON
OFFFor selecting whether or not the display is to
come on when the shutter is ON.
WHITE PRESET ONOFFFor selecting whether or not the display is to
come on when the AWB CH is set to PRESET.
EXTENDERON
OFFFor selecting whether or not the display is to
come on when the lens is in the extender mode.
25M/50MOFF
25M
50MFor selecting whether or not the display is to
come on when the 25M or 50M mode is
established.
BLACK STR ONOFFFor selecting whether or not the display is to
come on when BLACK STRETCH is being used.
MATRIX ONOFFFor selecting whether or not the display is to
come on when MATRIX is ON.
COLOR
CORRECTIONONOFFFor selecting whether or not the display is to
come on when COLOR CORRECTION is ON.
FILTER ONOFFFor selecting whether or not the display is to
come on when the filter combination is other
than 3200K and CLEAR.
SUPER V ONOFFFor selecting whether or not the display is to
come on when SUPER V is ON.
The underlining in the variable range column indicates the setting in the preset mode. 
						

							88
Chapter 7  Menu description tables
7-5-2 SHUTTER SPEED
ItemVariable
rangeRemarks
SYNCHRO SCANON
OFFFor selecting SYNCHRO SCAN as the shutter
speed to be used.
SUPER V ONOFFFor selecting SUPER V as the shutter speed
to be used.
POSITION1ON
OFFFor selecting POSITION1 as the shutter
speed to be used.
POSITION2ON
OFFFor selecting POSITION2 as the shutter
speed to be used.
POSITION3ON
OFFFor selecting POSITION3 as the shutter
speed to be used.
POSITION4ON
OFFFor selecting POSITION4 as the shutter
speed to be used.
POSITION5ON
OFFFor selecting POSITION5 as the shutter
speed to be used.
POSITION6ON
OFFFor selecting POSITION6 as the shutter
speed to be used.
7-5 OPERATION
7-5-1 CAMERA ID
ItemVariable
rangeRemarks
ID1: **********CAMERA ID setting 1
ID2: **********CAMERA ID setting 2
ID3: **********CAMERA ID setting 3
POSITION6 SEL 1/100
1/120
1/250
1/500
1/1000
1/2000
For selecting the shutter speed.
7-5-3 SHUTTER SELECT
ItemVariable
rangeRemarks
SUPER V MODEFRM1
FRM2For selecting the SUPER V mode switching.
FRM1:Normal mode
FRM2:After image reduction mode

In the SUPER V mode, the signals of the
photodiodes in the vertical direction of the
CCDs are not mixed with the output signals
so that the vertical resolution is enhanced.
The storage time is 1/30 sec. at the FRM1
setting and 1/60 sec. at the FRM2 setting
where the sensitivity is halved.
POSITION1 SEL1/100
1/120
1/250
1/500
1/1000
1/2000For selecting the shutter speed.
POSITION2 SEL 1/1001/120
1/250
1/500
1/1000
1/2000For selecting the shutter speed.
POSITION3 SEL 1/100
1/120
1/250
1/500
1/1000
1/2000
For selecting the shutter speed.
POSITION4 SEL 1/100
1/120
1/250
1/500
1/1000
1/2000
For selecting the shutter speed.
POSITION5 SEL 1/100
1/120
1/250
1/500
1/1000
1/2000
For selecting the shutter speed.
The underlining in the variable range column indicates the setting in the preset mode. 
						

							89
7
Chapter 7  Menu description tables
7-5-4 USER SW
ItemVariable
rangeRemarks
USER MAIN SW INHS.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AUDIO CH1
AUDIO CH2
REC SW
Y GET
RET SW
ATW
D.ZOOMFor allocating the USER MAIN switch
function.
USER1 SWINH
S.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AUDIO CH1
AUDIO CH2
REC SW
Y GET
RET SW
ATW
D.ZOOM
For allocating the USER1 switch function.
USER2 SW INH
S.GAIN
DS.GAIN
S.IRIS
I.OVR
S.BLK
B.STR
AUDIO CH1
AUDIO CH2
REC SW
Y GET
RET SW
ATW
D.ZOOM
For allocating the USER2 switch function.
7-5-5 SW MODE
ECU DATA SAVE ONOFFON:The settings controlled by the ECU are
stored in the memory when the ECU is
disconnected from the camera
recorder.
OFF:No camera related settings are stored
in memory.
ItemVariable
rangeRemarks
RET SWRECCHECK
CAM RETFor selecting the RET switch function.REC CHECK:The REC CHECK operation is
performed.
CAM RET:The return signal output operation
is performed.
S.BLK LVL OFF–10
–20
–30For setting the super black level.
AUTO KNEE SWON
OFFFor selecting whether or not the AUTO KNEE
switch is to be used.
SHD,ABB SW CTLON
OFFFor selecting whether or not digital dark
shading is to be activated by pressing the
ABS switch for a prolonged time (at least 8
seconds).
COLOR BARSSMPTE
FULL
BARS
SPLIT
ARIBFor selecting the color bars to be used.
SMPTE:SMPTE color bars 
FULL BARS:Full color bars
SPLIT:SPLIT color bars
ARIB:ARIB mult-format color bars
S.GAIN OFFL/M/H
S.GAINFor selecting the method used to release the
super gain mode.
L/M/H:The mode is released by making a
change in the L/M/H switch position.
S.GAIN:The mode is released using only
the S.GAIN switch (USER switch).
DS.GAIN OFF L/M/HDS.GAINFor selecting the method used to release the
digital super gain mode (cumulative gain).
L/M/H:
The mode is released by making a
change in the L/M/H switch position.
DS.GAIN:The mode is released using only the
DS.GAIN switch (USER switch).
D.ZOOM SELZOOM
FOCUSFor selecting the method used to execute
digital zooming.
ZOOM:Digital zooming is available for use
at all times.
FOCUS:Digital zooming is executed for about
5 seconds as a focus assist function.
However, if recording is initiated at a
point within the 5 seconds, the
D.ZOOM function is forcibly
released.
The underlining in the variable range column indicates the setting in the preset mode. 
						

							90
Chapter 7  Menu description tables
7-5-6 WHITE BALANCE MODE
AWB BMEM
ATW
VARFor selecting the allocation of the WHITE BAL
switch position and Bch.
MEM:The switch position and Bch are
allocated as memory values when
AWB is executed.
ATW:The position and Bch are allocated as
ATW start switch functions.
VAR:The color temperature of B can be set
to vary using the COLOR TEMP B
menu item.
COLOR TEMP B3200K: 5600K
For setting the color temperature when AWB
B has been set to VAR.
ItemVariable
rangeRemarks
FILTER INHON
OFFFor selecting whether or not to keep the AWB
memory (Ach, Bch) data for each filter.
ON:The data is kept in the two Ach and Bch
memories for each filter used.
OFF:The data is kept for each filter.
SHOCKLESS AWB OFF
FAST
NORMAL
SLOW1
SLOW2
SLOW3
For selecting ON (FAST/NORMAL/SLOW1-3)
or OFF for SHOCKLESS AWB which ensures
that the setting of the white balance switch to
PRST, A or B is not accompanied by a shock.
In addition, the switching time can be
selected.
AWB AREA25%
50%
90%For selecting the AWB detection area.
25%:An area near the screen center
equivalent to 25% of the screen is
detected.
50%:An area near the screen center
equivalent to 50% of the screen is
detected.
90%:An area equivalent to 90% of the
screen is detected.
AWB & ABB
OFFSETONOFFFor selecting whether or not to reset the GAIN
and PED values on the ROP menu when
AWB or ABB is executed.
ON:The values are not reset.
OFF:The values are reset.
COLOR TEMP PRE3200K: 5600K
For selecting the AWB PRE color
temperature.
AWB AMEM
VARFor selecting the allocation of the WHITE BAL
switch position and Ach.
MEM:The switch position and Ach are
allocated as memory values when
AWB is executed.
VAR:The color temperature of A can be set
to vary using the COLOR TEMP A
menu item.
COLOR TEMP A3200K: 5600K
For setting the color temperature when AWB
A has been set to VAR.
ATW SPEEDNORMAL
SLOW
FASTFor selecting the ATW control speed.
7-5-7 USER SW GAIN
ItemVariable
rangeRemarks
S.GAIN
30 dB¢•For selecting whether or not to enable a
setting of 30 dB for SUPER GAIN.
¢:The 30 dB setting is enabled.
•:The 30 dB setting is disabled.
36 dB¢•For selecting whether or not to enable a
setting of 36 dB for SUPER GAIN.
¢:The 36 dB setting is enabled.
•:The 36 dB setting is disabled.
42 dB¢•For selecting whether or not to enable a
setting of 42 dB for SUPER GAIN.
¢:The 42 dB setting is enabled.
•:The 42 dB setting is disabled.
48 dB¢•For selecting whether or not to enable a
setting of 48 dB for SUPER GAIN.
¢:The 48 dB setting is enabled.
•:The 48 dB setting is disabled.
DS.GAIN
6 dB:¢•For selecting whether or not to enable a
setting increase of 6 dB for DS.GAIN.
¢:The 6 dB setting increase is enabled.
•:The 6 dB setting increase is disabled.
12 dB:¢•For selecting whether or not to enable a
setting increase of 12 dB for DS.GAIN.
¢:The 12 dB setting increase is enabled.
•:The 12 dB setting increase is disabled.
20 dB:¢•For selecting whether or not to enable a
setting increase of 20 dB for DS.GAIN.
¢:The 20 dB setting increase is enabled.
•:The 20 dB setting increase is disabled.
The underlining in the variable range column indicates the setting in the preset mode.