Panasonic Aj Lt85 Operating Instructions Manual

CUT EDITING PROCEDURE
41
Edit point checking, revising and clearing
To check the edit points:
Press the IN or OUT button of the VTR on whose tape the edit points are to be checked. The registered edit point now appears
on the counter display.
To check the edit point image:
Press together the IN or OUT button and GO TO button of the VTR on whose tape the image of the edit points is to be checked.
The VTR accesses the registered edit point, and its image appears on the monitor.
¥ If the VTR does not access...

CUT EDITING PROCEDURE
42
(Preview)
Rehearsal playback before proceeding with editing
When the PREVIEW button is pressed, the event just registered (event whose number appears on the display) will be pre-
viewed.
When preview is executed:
¥ The recorderÕs images are played back from the recorderÕs preroll point to the IN point and from the OUT point onward.
¥ The images to be edited from the IN point to OUT point appear on the recorderÕs monitor.
¥ The tapes in both the player and recorder travel as far...

CUT EDITING PROCEDURE
43
3. Editing execution
Once the necessary edit point settings have been registered, one event will be automatically edited if editing is now performed.
After editing has been performed, what has been edited can be checked using the ÒreviewÓ function.
AUTO
EDIT Preroll point
Preroll time
Playback
Rewind and playback
(review)
EditingPostroll time
With insert editingWith assemble editing Edit start point Edit start point/edit end point Overlap point
PauseEditingPausePlayback
(With...

CUT EDITING PROCEDURE
44
(Review)
When the REVIEW (SHIFT+PREVIEW) button is pressed, already edited event is played back.
To suspend the review, press the ALL STOP button.

Review can be performed immediately after editing is completed. Note that review cannot be performed if the unit is transferred
to another mode or if one of its function buttons is pressed.
-
---
-
--
-
--
-
- -
-
--
-
--
-
--
-
- -
EJECT
VTR1
POWER
RECCH1RESET
RECDIAGREMOTE
EXT VTRLOCAL-VTR1 VTR2CONTROLON
OFFREC
INHIBITOFFON
CH2
PB...

AUDIO SPLIT EDITING PROCEDURE
45
In the insert edit mode, the audio IN point can be offset from the video IN point for editing.
!Set VIDEO for the set-up menu item No.311 (SPLIT EDIT).
@Select the channel for insert editing.
#Register the video edit IN points of the player and recorder.
$Press the SPLIT button. Check that its lamp has lighted. The IN lamps on the time counters of the player and recorder flash.
%Search the playerÕs audio IN point, and press the playerÕs IN button while holding down the...

The video IN point can be offset from the audio IN point during insert editing.
!Set AUDIO for the set-up menu item No.311 (SPLIT EDIT).
@Select the insert editing channel.
#Enter the audio edit IN points of the player and recorder.
$Press the SPLIT button.
Check that the SPLIT button lamp has lighted.
The IN lamps on the player and recorder flash.
%Search the playerÕs video IN point, and press the playerÕs IN button while holding down the ENTRY button.  When the IN
point is entered, the IN lamp lights....

EDITING BY EDIT IN POINT SETTING ONLY
STILL PICTURE EDITING
47
!Search the edit IN points of the player and recorder.
@Press the PREVIEW button.
The position where the button was pressed is registered as the IN point, and this point is previewed.
#Press the recorderÕs OUT button while holding down the ENTRY button at the OUT point position.
The OUT point is registered and the player and recorder stop in about 1 second in the assemble edit mode while and in
about 2 seconds in the insert edit mode.
$Press...

AUTO TAG EDITING
48
Scenes can be edited in succession simply by registering the playerÕs edit IN point.
Since the recorderÕs tape is stopped at the edit OUT point, editing can be conducted merely by registering the playerÕs edit IN
point.
!Set set-up item No.305 (AUTO ENTRY) to REC.
@When the editing is completed, search the playerÕs IN point.
#Press the AUTO EDIT button.
Editing now commences.
$At the edit OUT point, press the AUTO EDIT button.
Editing is now completed.
-
---
-
--
-
--
-
- -
-
--
-
--...

TC JUMP FUNCTION
49
Editing is not normally possible in areas where the time code is discontinuous during the preroll period. However, using the TC
JUMP function, editing is performed using CTL as the reference in the preroll period and using TC as the reference after the IN
point has been passed (during edit recording). TC is displayed so that the unit can be operated as though TC editing were being
performed all the time.
!Set the menu No. 511 (TC JUMP) to VTR1, VTR2 or ALL.
(Select the VTR for which...

EVENT EDITING
50
Registering events
Events are registered in sequence from event No.01 to 99, 00.
How to register events
¥Auto editing
Press the AUTO EDIT button.
After editing has been executed, the numbers are automatically incremented by 1.
¥Registering an event without executing editing
Press the STORE (SHIFT+REC) buttons.
The event numbers are incremented by 1.
When an unregistered event number (displayed as ÒnÓ) is registered:
The next event number is displayed.
¥ When an event number is accessed...