Panasonic Aj Lt85 Operating Instructions Manual
Have a look at the manual Panasonic Aj Lt85 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CUT EDITING PROCEDURE 41 Edit point checking, revising and clearing To check the edit points: Press the IN or OUT button of the VTR on whose tape the edit points are to be checked. The registered edit point now appears on the counter display. To check the edit point image: Press together the IN or OUT button and GO TO button of the VTR on whose tape the image of the edit points is to be checked. The VTR accesses the registered edit point, and its image appears on the monitor. ¥ If the VTR does not access the edit point, it means that the edit point has not been registered. To check the total time: To check the total time of each edit,press the IN and OUT buttons together. The edit time now appears on the counter. To check the total time of the entire editing,press the TOTAL button. The total time is displayed while this button is held down. To revise an edit point in 1-frame increments Press the Ò+Ó or ÒÐÓ button while holding down the IN or OUT button. The Ò+Ó button increases the registered edit point in 1-frame increments. The ÒÐÓ button decreases the registered edit point in 1-frame increments. To clear an edit point Press the corresponding RESET button while holding down the IN or OUT button of the edit point which is to be cleared. Cut editing procedure
CUT EDITING PROCEDURE 42 (Preview) Rehearsal playback before proceeding with editing When the PREVIEW button is pressed, the event just registered (event whose number appears on the display) will be pre- viewed. When preview is executed: ¥ The recorderÕs images are played back from the recorderÕs preroll point to the IN point and from the OUT point onward. ¥ The images to be edited from the IN point to OUT point appear on the recorderÕs monitor. ¥ The tapes in both the player and recorder travel as far as a point 2 seconds after the OUT point and stop. In the assemble mode, the tape in the recorder travels as far as a point 1 second after the IN point and stops while the recorderÕs images are not played back even when the playerÕs tape passes the OUT point. To start preview again from the beginning while preview is in progress: Press the PREVIEW button. To reset the OUT point more toward the tape beginning while preview is in progress: Press the recorder or player OUT button while holding down the ENTRY button at the scene where the OUT point is to be regis- tered. ¥ In the insert mode, the recorderÕs tape position where the above two buttons were pressed is now registered as the new OUT point, and preview is concluded. ¥ In the assemble mode, the new OUT point is automatically calculated and registered. To suspend preview and execute automatic editing: Press the AUTO EDIT button. To recall the contents of the previous preview: Press the LAST EDIT button. Each time this button is pressed, the contents of the current preview and the previous preview are toggled. - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP
CUT EDITING PROCEDURE 43 3. Editing execution Once the necessary edit point settings have been registered, one event will be automatically edited if editing is now performed. After editing has been performed, what has been edited can be checked using the ÒreviewÓ function. AUTO EDIT Preroll point Preroll time Playback Rewind and playback (review) EditingPostroll time With insert editingWith assemble editing Edit start point Edit start point/edit end point Overlap point PauseEditingPausePlayback (With continuous automatic editing, input the next event without executing editing.) * After editing has been executed, the EVENT No. is added, and what has been the recorderÕs edit OUT point is automatically calculated as the edit IN point. [However, this is only when an automatic setting is used for set-up menu item No.305 (AUTO ENTRY).] * To end editing at any time, press the AUTO EDIT button. The position where the button was pressed is registered as the OUT point. When the AUTO EDIT button is pressed, the automatic editing of one event is commenced. - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP Cut editing procedure
CUT EDITING PROCEDURE 44 (Review) When the REVIEW (SHIFT+PREVIEW) button is pressed, already edited event is played back. To suspend the review, press the ALL STOP button. Review can be performed immediately after editing is completed. Note that review cannot be performed if the unit is transferred to another mode or if one of its function buttons is pressed. - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP
AUDIO SPLIT EDITING PROCEDURE 45 In the insert edit mode, the audio IN point can be offset from the video IN point for editing. !Set VIDEO for the set-up menu item No.311 (SPLIT EDIT). @Select the channel for insert editing. #Register the video edit IN points of the player and recorder. $Press the SPLIT button. Check that its lamp has lighted. The IN lamps on the time counters of the player and recorder flash. %Search the playerÕs audio IN point, and press the playerÕs IN button while holding down the ENTRY button. Once the IN point has been registered, the IN lamp has lighted. ^Press the SPLIT button. The SPLIT lamp flashes. &Register the OUT point of the player or recorder. *Press the PREVIEW button to preview the points. (Press the AUTO EDIT button. Revising an edit IN point Check that the SPLIT lamp has lighted, and repeat steps 4 and 5. Displaying the audio split amount Press the IN and OUT buttons together while the SPLIT lamp flashes. The difference between the audio split IN point and video IN point is displayed on the time counter. While the SPLIT lamp is lighted, the audio split IN and video OUT points cannot be revised simultaneously by pressing the Ò+Ó or ÒÐÓ button. ¥ If the SPLIT lamp flashes, it means that the audio split IN point has been registered. ¥ Check that VIDEO has been set for the set-up menu item No.311 (SPLIT EDIT). - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP Audio split editing procedure
The video IN point can be offset from the audio IN point during insert editing. !Set AUDIO for the set-up menu item No.311 (SPLIT EDIT). @Select the insert editing channel. #Enter the audio edit IN points of the player and recorder. $Press the SPLIT button. Check that the SPLIT button lamp has lighted. The IN lamps on the player and recorder flash. %Search the playerÕs video IN point, and press the playerÕs IN button while holding down the ENTRY button. When the IN point is entered, the IN lamp lights. ^Press the SPLIT button. The SPLIT button lamp changes from the lighted to a flashing status. &Enter the OUT point of the player or recorder. *Press the PREVIEW button to conduct a preview. (Press the AUTO EDIT button. Correcting an edit IN point Check that the SPLIT button lamp is lighted, and repeat steps $and %. Displaying the video split amount Press the IN and OUT buttons at the same time while the SPLIT lamp is flashing. The difference between the video split IN point and audio IN point is displayed on the time counter. The video split IN point and audio OUT point cannot be corrected at the same time by pressing the + or Ð button while the SPLIT button lamp is lighted. ¥ The video split IN point is entered while the SPLIT button lamp is flashing. ¥ Check that AUDIO is set for the set-up menu item No.311 (SPLIT EDIT). - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP VIDEO SPLIT EDITING PROCEDURE 46
EDITING BY EDIT IN POINT SETTING ONLY STILL PICTURE EDITING 47 !Search the edit IN points of the player and recorder. @Press the PREVIEW button. The position where the button was pressed is registered as the IN point, and this point is previewed. #Press the recorderÕs OUT button while holding down the ENTRY button at the OUT point position. The OUT point is registered and the player and recorder stop in about 1 second in the assemble edit mode while and in about 2 seconds in the insert edit mode. $Press the AUTO EDIT button. Editing now commences. When executing editing without preview Press the AUTO EDIT button instead of the PREVIEW button in step 2. At the position where editing is to be completed, press the AUTO EDIT button. !Register the IN point and OUT point of the player (VTR1) as the same point. ¥ These points can be registered as the same point by simultaneously pressing the IN button, OUT button and SHIFT/ENTRY button of the player (VTR1). @Set and register both the IN point and OUT point of the recorder (VTR2). ¥ Open-ended execution is possible even when the IN point alone is registered. #Press the AUTO EDIT button to execute editing. The still picture of the player (VTR1) at the point registered in step !is now edited. The still picture editing can be operated only when the OPERATION MODE switch is set to ÒINT.Ó - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP Editing by edit IN point setting only
AUTO TAG EDITING 48 Scenes can be edited in succession simply by registering the playerÕs edit IN point. Since the recorderÕs tape is stopped at the edit OUT point, editing can be conducted merely by registering the playerÕs edit IN point. !Set set-up item No.305 (AUTO ENTRY) to REC. @When the editing is completed, search the playerÕs IN point. #Press the AUTO EDIT button. Editing now commences. $At the edit OUT point, press the AUTO EDIT button. Editing is now completed. - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP TRACK FUNCTION This function efficiently sets the playerÕs edit points in accordance with any change which is made in the recorderÕs edit IN point. !Change the IN point of the recorder (VTR2). @Press the TRACK [SHIFT + FF (VTR1)] button. ¥ The IN point of the player (VTR1) is automatically changed in accordance with the change made in step !. ¥ The colon (:) between the hours and minutes of the on-screen counter cahnges to a dot (.) to indicate that the track mode is now estblished. ¥ The TC (UB or CTL) display on the display tube flashes to indicate that the track mode is now established. #When the IN point of recorder (VTR2) is changed in the track mode, the IN point of the player (VTR1) is also automatically changed. When an edit point of the player (VTR1) is next changed, the track mode is released, and the normal mode is restored. When ÒALLÓ is selected for the set-up menu item No. 305 (AUTO ENTRY) setting, the IN point of the player (VTR1) will always be changed in accordance with the change made in the IN point of the recorder (VTR2) even when the track mode is not estab- lished manually. 01:23:45:01 à01 23:45:01. Normal mode Track mode
TC JUMP FUNCTION 49 Editing is not normally possible in areas where the time code is discontinuous during the preroll period. However, using the TC JUMP function, editing is performed using CTL as the reference in the preroll period and using TC as the reference after the IN point has been passed (during edit recording). TC is displayed so that the unit can be operated as though TC editing were being performed all the time. !Set the menu No. 511 (TC JUMP) to VTR1, VTR2 or ALL. (Select the VTR for which the TC JUMP function is to be used). @Carry out the regular automatic editing operations. In the preview, automatic editing or review mode, the tape is first cued up to the IN point, it is prerolled using the CTL value of the IN point as a reference, and it begins its approach. After it has passed the IN point and the edit recording mode is established, editing continues using the TC as the reference. TC jump function
EVENT EDITING 50 Registering events Events are registered in sequence from event No.01 to 99, 00. How to register events ¥Auto editing Press the AUTO EDIT button. After editing has been executed, the numbers are automatically incremented by 1. ¥Registering an event without executing editing Press the STORE (SHIFT+REC) buttons. The event numbers are incremented by 1. When an unregistered event number (displayed as ÒnÓ) is registered: The next event number is displayed. ¥ When an event number is accessed and the edit data is revised, the data which has been revised is registered in the event number concerned. ¥ When an event is accessed and editing is executed without further ado, the event number remains unchanged. When Ò00Ó appears as the event number: This signifies the one hundredth event. The overwrite mode (all clear) or overwrite prohibited mode is established depending on the EDL auto clear setting (set-up item No.309 ÒEDL AUTO CLRÓ). ¥When EDL AUTO CLR is OFF The overwrite prohibited mode is established. ÒFULLÓ appears instead of the event number. When any function button is pressed, the event number is returned to Ò00Ó and the status which results when the edit data for event No.00 is accessed is established. ¥When EDL AUTO CLR is ON The overwrite mode is established. The event number appears as Òn00,Ó and the registered edit data is cleared. A new event can now be registered. - --- - -- - -- - - - - -- - -- - -- - - - EJECT VTR1 POWER RECCH1RESET RECDIAGREMOTE EXT VTRLOCAL-VTR1 VTR2CONTROLON OFFREC INHIBITOFFON CH2 PB AUDIO LEVELREW FFSTOPSTB OFFTRACKPLAY STILL 1ST EDIT BS EVENTSPLIT ASMBL IN OUT VTR1 VTR2 VTR1 VTR2 PREROLLSYNCHRO7 5 3CF ON OFFCH1 MIX CH2V1 V1•2 V2SWAP NORM MIXAUDIO MONITORSPEAKER/ HEADPHONESAUDIO SWAP DUMP LOADEDL CLEARFS RECALL LAST EDIT VA1A2TC PLAY IN OUTGO TO ENTRY / SHIFT EDIT MODE COUNTERCTLTC UBVTR1 EJECT VTR2 RESET RECSTORE STOPSTB OFF MENUEDIT STILLREWFF VTR2 RECCH1 CH2 OPERATION MODEVTR2 AUDIO INPUT SELECTEDITINTEXTSEPARATECH1 CH2VTR1EXT PBAUDIO LEVEL PREVIEWREVIEW MULTIAUTO EDITALL STOP*When event editing is performed in the CTL mode, the error may accumulate causing the edit points to deviate considerably. It is therefore recommended that event editing be performed in the TC mode.