Panasonic Aj Hd1700 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Aj Hd1700 Operating Instructions Manual. The Panasonic manuals for Cassette Player are available online for free. You can easily download all the documents as PDF.
Page 121
121 Error messages Display•Description •VTR operation and remedial action T REEL TORQUE ERRIf an abnormal torque applied to the take-up reel motor is detected, the AUTO OFF lamp lights, and the message display blinks. VTR:Stops. •Set the POWER switch to OFF and then back to ON again. S REEL TORQUE ERRIf an abnormal torque applied to the supply reel motor is detected or if an abnormal current flowing to the current-sensing resistor is detected, the AUTO OFF lamp lights, and the message display blinks....
Page 122
![Page 122
122
The VTR can be operated by commands when the
RS-232C interface is used. (Refer to the command
tables on page 125 and 126.)
∫
Condition for acknowledging
commands from RS-232C interface
Setup menu item No.204 (RS232C SEL): ON
If the above condition is not met,
[ACK]+[STX]ER001[EXT] is returned to the external
component. Whether [ACK] is returned depends on
the setting which has been selected for setup menu
item No.209 (RETURN ACK).
Hardware specifications
External interface specifications
RS-232C...](http://img.usermanuals.tech/thumb/58/67770/w300_aj-hd1700_en_om_d-121.png "Page 122
122
The VTR can be operated by commands when the
RS-232C interface is used. (Refer to the command
tables on page 125 and 126.)
∫
Condition for acknowledging
commands from RS-232C interface
Setup menu item No.204 (RS232C SEL): ON
If the above condition is not met,
[ACK]+[STX]ER001[EXT] is returned to the external
component. Whether [ACK] is returned depends on
the setting which has been selected for setup menu
item No.209 (RETURN ACK).
Hardware specifications
External interface specifications
RS-232C...")
122 The VTR can be operated by commands when the RS-232C interface is used. (Refer to the command tables on page 125 and 126.) ∫ Condition for acknowledging commands from RS-232C interface Setup menu item No.204 (RS232C SEL): ON If the above condition is not met, [ACK]+[STX]ER001[EXT] is returned to the external component. Whether [ACK] is returned depends on the setting which has been selected for setup menu item No.209 (RETURN ACK). Hardware specifications External interface specifications RS-232C...
Page 123
123 Software specifications (protocol) 1.Communication parameters RS-232C interface Communication system Asynchronous, full duplex Transfer rate300, 600, 1200, 2400, 4800 or 9600bps Bit length 7 bits or 8 bits Stop bit 1 bitor 2 bits Parity bit None, odd or even ACK codeReturnedor not returned ACK is the code which is returned from the VTR to the controller when data has been successfully sent from the controller. The underlining (__) denotes the factory setting mode. Communication parameterSetup menu...
Page 124
![Page 124
124
RS-232C interface
3. Return format
[VTR > >
controller (PC)]
The following responses are made to the
commands. If necessary, more than one
response is made.
∫
When the communication has ended
successfully
1. The receive completion message is returned.
[ACK]
06h
2. The execution completion message is
returned.
[STX] [command] [data] [ETX]
02h XX XX XX XX.....
XX 03h
[command]:
This is the message (data) which is returned
or the execution completion message
identifier.
[data]:
This is the data to be...](http://img.usermanuals.tech/thumb/58/67770/w300_aj-hd1700_en_om_d-123.png "Page 124
124
RS-232C interface
3. Return format
[VTR > >
controller (PC)]
The following responses are made to the
commands. If necessary, more than one
response is made.
∫
When the communication has ended
successfully
1. The receive completion message is returned.
[ACK]
06h
2. The execution completion message is
returned.
[STX] [command] [data] [ETX]
02h XX XX XX XX.....
XX 03h
[command]:
This is the message (data) which is returned
or the execution completion message
identifier.
[data]:
This is the data to be...")
124 RS-232C interface 3. Return format [VTR > > controller (PC)] The following responses are made to the commands. If necessary, more than one response is made. ∫ When the communication has ended successfully 1. The receive completion message is returned. [ACK] 06h 2. The execution completion message is returned. [STX] [command] [data] [ETX] 02h XX XX XX XX..... XX 03h [command]: This is the message (data) which is returned or the execution completion message identifier. [data]: This is the data to be...
Page 125
![Page 125
125
RS-232C interface
5. Command table
∫
Commands relating to operation control
•As the return (completion) message, [ACK] is
returned when data is received, and only the
execution message which is subsequently
returned is listed in the table.
•If a command not listed in the table is received,
ER001 (invalid command) is returned after
[ACK].
VTR
operationSend command
STOP[STX] OSP [ETX]
45[STX] OSP [ETX]
This command is for stopping the tape transport.
The resulting output picture and sound statuses...](http://img.usermanuals.tech/thumb/58/67770/w300_aj-hd1700_en_om_d-124.png "Page 125
125
RS-232C interface
5. Command table
∫
Commands relating to operation control
•As the return (completion) message, [ACK] is
returned when data is received, and only the
execution message which is subsequently
returned is listed in the table.
•If a command not listed in the table is received,
ER001 (invalid command) is returned after
[ACK].
VTR
operationSend command
STOP[STX] OSP [ETX]
45[STX] OSP [ETX]
This command is for stopping the tape transport.
The resulting output picture and sound statuses...")
125 RS-232C interface 5. Command table ∫ Commands relating to operation control •As the return (completion) message, [ACK] is returned when data is received, and only the execution message which is subsequently returned is listed in the table. •If a command not listed in the table is received, ER001 (invalid command) is returned after [ACK]. VTR operationSend command STOP[STX] OSP [ETX] 45[STX] OSP [ETX] This command is for stopping the tape transport. The resulting output picture and sound statuses...
Page 126
![Page 126
126
RS-232C interface
∫
Commands relating to inquiries
•In terms of the return (completion) message,
[ACK] is returned when data is received, and
only the execution message which is
subsequently returned is listed in the table.
•In the case of commands not listed in the table
below, ER001 (invalid command) is returned
after [ACK].
VTR
operationSend command
CTL/TC DATA
REQUEST[STX] QCD [ETX]
45[STX] CD data [ETX]
This command is for inquiring about the counter
value.
data = f w gh mm ss ff
f=F
w=S
gh =...](http://img.usermanuals.tech/thumb/58/67770/w300_aj-hd1700_en_om_d-125.png "Page 126
126
RS-232C interface
∫
Commands relating to inquiries
•In terms of the return (completion) message,
[ACK] is returned when data is received, and
only the execution message which is
subsequently returned is listed in the table.
•In the case of commands not listed in the table
below, ER001 (invalid command) is returned
after [ACK].
VTR
operationSend command
CTL/TC DATA
REQUEST[STX] QCD [ETX]
45[STX] CD data [ETX]
This command is for inquiring about the counter
value.
data = f w gh mm ss ff
f=F
w=S
gh =...")
126 RS-232C interface ∫ Commands relating to inquiries •In terms of the return (completion) message, [ACK] is returned when data is received, and only the execution message which is subsequently returned is listed in the table. •In the case of commands not listed in the table below, ER001 (invalid command) is returned after [ACK]. VTR operationSend command CTL/TC DATA REQUEST[STX] QCD [ETX] 45[STX] CD data [ETX] This command is for inquiring about the counter value. data = f w gh mm ss ff f=F w=S gh =...
Page 127
127 RS-232C interface ∫ Microsoft QuickBASIC sample program CLS STX$ = CHR$(&H2): ETX$ = CHR$ (&H3): NAK$ = CHR$(15): ACK$ = CHR$(&H6) PRINT *** RS-232C COMMUNICATION SAMPLE PROGRAM *** PRINT Type Command QUIT to quit. PRINT REM *** Communication Port Initial & Open *** REM Port 1,9600Bps,No parity,8 bit data,1 stop bit OPEN COM1:9600,N,8,1 FOR RANDOM AS #1 LEN = 256 REM *** Input Command & Send Command *** SendCmd: INPUT Input Command =; SEND$ IF SEND$ = QUIT THEN GOTO ProgEnd PRINT #1, STX$ + SEND$ +...
Page 128
128 Connector signals VIDEO IN HD SERIAL IN (DIGITAL)BNC k1, active-through (BNC k1) HD REF IN BNC k2, loop-through, 75™ termination switch provided SD REF IN BNC k2, loop-through, 75™ termination switch provided SD SERIAL IN (DIGITAL)BNC k1, active-through (BNC k1) (board, option) SDTI IN BNC k 1 (board, option) VIDEO OUT HD SERIAL OUT (DIGITAL)BNC k 4 SD SERIAL OUT (DIGITAL)BNC k 2 VIDEO OUT BNC k 3 HD REF OUT BNC k 1 SD REF OUT BNC k 1 SDTI OUT BNC k1 (board, option) AUDIO IN HD SERIAL IN (DIGITAL)BNC...
Page 129
CUE INPUT IMPEDANCE SW This sets the CUE input impedance. HIGH/600™ 129 Connector signals PARALLEL REMOTE (50P) Refer to 50P IN/OUT ASSIGN on the function menu (page 75) for the connection pin signals. ENCODER REMOTE(15P) Pin No. Signal 1FRAME GROUND 4REM (G) 7REM RX (X) REMOTE CONTROL PROTOCOL RECEIVE 8REM TX (X)REMOTE CONTROL PROTOCOL TRANSMIT 14REM RX (Y) REMOTE CONTROL PROTOCOL RECEIVE 15REM TX (Y)REMOTE CONTROL PROTOCOL TRANSMIT RS-232C (D-SUB 25-pin, crossover cable supported) Pin No. Signal...
Page 130
![Page 130
130
[GENERAL]
indicates the safety information.
Power supply: AC 100–240V, 50–60 Hz (AJ-HD1700P)
AC 100–240V, 50–60 Hz (AJ-HD1700E)
Power consumption: 240W
Operating ambient temperature:
41x
F to 104x
F (5x
C to 40x
C)
Operating ambient humidity:
10% to 80% (no condensation)
Weight:
Approx. 48.4 lbs (22 kg)
Dimensions (W k
H k
D):
16-3/4 (max. 17-3/16 ) k
6-15/16 k
17-11/16 inches
(not including supporting feet, jacks and connectors, JOG
dial and fan)
424 (max. 435.4) k
175.2 k
448.9 mm
Recording...](http://img.usermanuals.tech/thumb/58/67770/w300_aj-hd1700_en_om_d-129.png "Page 130
130
[GENERAL]
indicates the safety information.
Power supply: AC 100–240V, 50–60 Hz (AJ-HD1700P)
AC 100–240V, 50–60 Hz (AJ-HD1700E)
Power consumption: 240W
Operating ambient temperature:
41x
F to 104x
F (5x
C to 40x
C)
Operating ambient humidity:
10% to 80% (no condensation)
Weight:
Approx. 48.4 lbs (22 kg)
Dimensions (W k
H k
D):
16-3/4 (max. 17-3/16 ) k
6-15/16 k
17-11/16 inches
(not including supporting feet, jacks and connectors, JOG
dial and fan)
424 (max. 435.4) k
175.2 k
448.9 mm
Recording...")
130 [GENERAL] indicates the safety information. Power supply: AC 100–240V, 50–60 Hz (AJ-HD1700P) AC 100–240V, 50–60 Hz (AJ-HD1700E) Power consumption: 240W Operating ambient temperature: 41x F to 104x F (5x C to 40x C) Operating ambient humidity: 10% to 80% (no condensation) Weight: Approx. 48.4 lbs (22 kg) Dimensions (W k H k D): 16-3/4 (max. 17-3/16 ) k 6-15/16 k 17-11/16 inches (not including supporting feet, jacks and connectors, JOG dial and fan) 424 (max. 435.4) k 175.2 k 448.9 mm Recording...