Optoma Projector Tw865 Nlw User Manual
Have a look at the manual Optoma Projector Tw865 Nlw User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1077 Optoma manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
English4 User Controls SETUP Language Choose the multilingual OSD menu. Press ◄ or ► into the sub menu and then use the ▲ or ▼ to select your preferred language. Press “Enter” to finalize the selection. Projection Front-Desktop This is the default selection. The image is projected straight on the screen. Rear-Desktop When selected, the image will appear reversed. Front-Ceiling When selected, the image will turn upside down. Rear-Ceiling When selected, the image will appear reversed in upside down position. NOTE Rear-Desktop and Rear-Ceiling are to be used with a translu-cent screen.
English42 User Controls Screen Type Choose the screen type from 6:0 or 6:9. Menu Location Choose the menu location on the display screen. Projector ID ID definition can be set up by menu (range 0-99), and allow user control an individual projector by RS232. Refer to pages 87-90 for the complete list of RS232 commands. NOTE “Screen Type” is only available for WXGA model. SETUP (Continued) NOTE “Image Blending” is only available when “Geometry” is enabled.
English43 User Controls SETUP | Lens Function Focus Adjust focus function on the projected image. Zoom Adjust zoom function on the projected image. Lens Shift Shift the projected image. Lock: This function can not be used by user. Unlock: This function can be used by user. Lens Type Choose the lens type from A0, A02 or A03. Lens Calibration Perform calibration and return lens to the center position. Blending Pattern Show grid pattern for using image blending. Off: Choose “Off” to turn off grid pattern. Green: Choose “Green” to show green grid pattern for using image blending. Magenta: Choose “Magenta” to show magenta grid pattern for using image blending.
English44 User Controls SETUP | Security Security Timer On: Choose “On” to use security verification when turning on projector. Off: Choose “Off” to be able to switch on the projector without password verification. Change Password First time: Press “” to set the password. The password has to be 4 digits. Use number button on the remote to enter your new pass- word and then press “” key to confirm your password. Change Password: Press “” to input old password. Use number button to enter current password and then press “” to confirm. Enter new password (4 digits in length) using the number buttons on the remote, then press “” to confirm. Enter new password again and press “” to confirm. If the incorrect password is entered 3 times, the projector will automatically shut down. If you have forgotten your password, please contact your local office for support. Security On: Choose “On” to use security verification when turning on projector. Off: Choose “Off” to be able to switch on the projector without password verification. . 2. 3. . 2. 3. 4. NOTE Password default value is “234” (first time). Always keep the password in your files. If the password is forgotten or lost, the projector will have to be sent to your local au-thorized service center.
English45 User Controls SETUP | Signal (RGB) Frequency Change the display data frequency to match the frequency of your computer’s graphic card. Use this function only if the image ap- pears to fl icker vertically. Phase Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or fl ickers, use this function to correct it. H. Position Press the ◄ to move the image left. Press the ► to move the image right. V. Position Press the ◄ to move the image down. Press the ► to move the image up. Automatic Automatically detects the signal. If you use this function, the phase, frequency items are grayed out, and if signal is not auto- matic, the phase, frequency items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again. NOTE “Signal” is only supported in Analog VGA (RGB) signal.
English46 User Controls SETUP | Signal (Video) White Level Allow user adjust White Level when inputting S-Video or Video/ CVBS signals. Black Level Allow user adjust Black Level when inputting S-Video or Video/ CVBS signals. Saturation Adjust a video image from black and white to fully saturated color. Press the ◄ to decrease the amount of saturation in the im- age. Press the ► to increase the amount of saturation in the image. IRE Adjust measurement of composite video signals. NOTE “Signal” is not supported when the source is HDMI or DVI-D. NOTE “IRE” is only sup-ported on NTSC signal.
English47 User Controls Internal Speaker Choose the “On” or “Off” to turn on or off the internal speaker. Mute Choose the “On” to turn mute on. Choose the “Off” to turn mute off. Volume Press the ◄ to decrease the volume. Press the ► to increase the volume. Audio Input The default audio settings are on the back panel of the projector. Use this option to reassign any of the Audio Inputs ( ,2 or 3) to the current image source. Each Audio input can be assigned to more than one video source. Audio : VGA . Audio 2: VGA 2. Audio 3: S-Video/Video. Default: Set Input back to default video source. SETUP | Audio Settings
English48 User Controls SETUP | Advanced Logo Use this function to set the desired startup screen. If changes are made they will take effect the next time the projector is powered on. Optoma: The default startup screen. Neutral: Logo is not displayed on startup screen. User: Use stored picture from “Logo Capture” function. Logo Capture Press to capture an image of the picture currently displayed on screen. Closed Captioning If changes are made they will take effect the next time the projec- tor is powered on. Off: select “off” to turn off the closed captioning feature. CC: CC language: American English. CC2: CC2 language (depending on the TV channel of the user): Spanish, French, Portuguese, German, Danish. NOTE For successful logo capture, please ensure that the input signal does not exceed the projector’s native resolution. (280 x 800 or 280 x 720).Do not use signal with de-interlace.Do not turn off the projec-tor during logo capturing.
English49 User Controls SETUP | Network Network State Display the network connection status. DHCP Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open. On: Assign an IP address to the projector from an external DHCP server automatically. Off: Assign an IP address manually. IP Address Select an IP address. Subnet Mask Select subnet mask number. Gateway Select the default gateway of the network connected to the projec- tor. DNS Select DNS number. Apply Press “” and then choose “Yes” to apply the selection.
English50 User Controls How to use web browser to control your projector Turn on DHCP to allow the DHCP server to automatically assign an IP, or manually enter the required network information. Then choose apply and press “ ” button to complete the confi guration process. Open your web browser and type in the projector’s IP address from the OSD LAN screen. The following web page will display as below: If connecting the projector to external Crestron control hardware, the settings can be found in the [tools] tab. (see picture). . 2. 3. 4. Please note, each fi eld can only contain a limited number of characters, as shown in the table below. (spaces and the other punctuation included): CategoryItemInput-Length (characters) Crestron Control IP Address5 IP ID2 Port5 Projector Projector Name0 Location9 Assigned To9 Network Confi gu-ration DHCP (Enabled)(N/A) IP Address5 Subnet Mask5 Default Gateway5 DNS Server5 User Password Enabled(N/A) New Password5 Confi rm5 Admin Password Enabled(N/A) New Password5 Confi rm5