Optoma Projector Movietime Dv11 User Manual

DVD Projector  *  41
English

USER CONTROLS

How to Operate DVD Menu
1.   To open the DVD OSD menu, press [Projector Menu] on the remote 
control, go to “System-->DVD Setup”. 
2.   When DVD OSD is displayed, use   keys to select any item in 
the main menu. While making a selection on a particular page, press 
[Enter] or  key to enter sub menu.
3.   Use   keys to select the desired item and adjust the settings by 
  key.
4.   Select the next item to be adjusted in the sub menu and adjust as 
described...

42  *  DVD Projector
English

USER CONTROLS

Menu Tree for DVD 

DVD Projector  *  43
English

USER CONTROLS

System Setup
 TV System
Select system as you watching TV. 
 Screen Saver
Choose “On” to start the screen protection function, while 
stopping, opening, no discs or about 60 seconds of picture 
inactive state on the tray.  Choose “Off” to cancel the screen 
saver function.
 TV Type
Use this function to choose your desired TV type.
1.   16:9 (widescreen): available option for connection 
with widescreen TV.
2.   4:3LB: (mailbox): suitable for use with standard...

44  *  DVD Projector
English

USER CONTROLS

When you forget the old password, press the initial password “0000”.
NoteNote
 Password
The default setting is “Password is locked”, can’t choose “Rating” 
or revise the password. If need to select “Rating” to press the nu-
merical key and importing the initial password of the one machine: 
0000, then press the enter button to confirm. When you need to 
change the password, input the old password first, and then input 
the new password. (The effective password...

DVD Projector  *  45
English

USER CONTROLS

Language Setup
 OSD Language
Select your preferred language for the on-screen display 
menu. 
 Audio Lang
Select the audio language
 Subtitle Lang
Select the subtitle language
 Menu Lang
Select your preferred language for DVD menu.
 Exit Setup
Exit this menu. 

46  *  DVD Projector
English

USER CONTROLS

Digital Setup
 SPDIF Out
Choose the appropriate Digital Audio settings for your equip-
ment as it only affect during the playback of DVD discs of the 
DVD player.
▀■  SPDIF/Off: Turn off the sound.
▀■  SPDIF/RAW: Select this function, when the player is con-
nected to Dolby Digital Decoder.
▀■  SPDIF/PCM: Select this function, when the player is not 
connected to Dolby Digital Decoder.
 Key
 Adjust the key of sound.
 Exit Setup
Exit this menu. 

DVD Projector  *  47
English

USER CONTROLS

Video Setup
  Brightness
Adjust the brightness of the image.
▀■  Press  to darken an image.
▀■  Press  to lighten an image.
 Contrast
Contrast controls the degree of difference between the light-
est and darkest parts of the picture. Adjusting the contrast 
changes the amount of black and white with an image.
▀■  Press  to decrease the contrast.
▀■  Press  to increase the contrast.
 Saturation
Adjust the color balance of red and green.
▀■  Press  to increase...

48  *  DVD Projector
English

MAINTENANCE

Speaker Setup
 Downmix
Depending on the audio channels you got on your audio sys-
tem. You may decide the Downmix of the channels, whether 
they are “LT/RT”, “Stereo” or “Off”.
 OP Mode
 ▀■  Line out: Carries on the linear compression to the input 
signal. The volume slightly suits the evening to use.
 D.R.C
 Dynamic rage decides the pitch of volume.  You may set 
them as “Full”, 6/8, 4/8, 2/8 or “Off”. To compress the high 
volume Dolby Digital movie, prevent...

DVD Projector  *  49
English

MAINTENANCE

Troubleshooting
If you experience a problem with your projector, please refer to 
the following information. If a problem persists, please contact 
your local reseller or service center.
Image Problems
 No image appears on screen:
  Ensure that all the cables and power cord are correctly and securely 
connected as described in the “Installation” section.
  Ensure that connector pins are not bent or broken.
  Check the [Power] or [Stand By] button is pressed....

50  *  DVD Projector
English

MAINTENANCE

6.   Select the “Change” button under the “Monitor” tab.
7.   Click on “Show all devices.” Next, select “Standard monitor 
types” under the SP box; choose the resolution mode you need 
under the “Models” box.
8.   Verify that the resolution setting of the monitor display is 
lower than or equal to 1280 x 1024.
  If using a Notebook PC:
1.  First, follow the steps above to adjust resolution of the com-
puter.
2.  Press the toggle output settings. example:...