Optoma Projector Movietime Dv11 User Manual

							
DVD Projector  *  41
English

USER CONTROLS

How to Operate DVD Menu
1.   To open the DVD OSD menu, press [Projector Menu] on the remote 
control, go to “System-->DVD Setup”. 
2.   When DVD OSD is displayed, use   keys to select any item in 
the main menu. While making a selection on a particular page, press 
[Enter] or  key to enter sub menu.
3.   Use   keys to select the desired item and adjust the settings by 
  key.
4.   Select the next item to be adjusted in the sub menu and adjust as 
described above.
5.   Choose the “Exit Setup” to confirm, and the screen will return to the 
main menu.
6.   To exit, press [Setup]/[Enter].
Main menuSub-menuItem 
						

							
42  *  DVD Projector
English

USER CONTROLS

Menu Tree for DVD 
						

							
DVD Projector  *  43
English

USER CONTROLS

System Setup
 TV System
Select system as you watching TV. 
 Screen Saver
Choose “On” to start the screen protection function, while 
stopping, opening, no discs or about 60 seconds of picture 
inactive state on the tray.  Choose “Off” to cancel the screen 
saver function.
 TV Type
Use this function to choose your desired TV type.
1.   16:9 (widescreen): available option for connection 
with widescreen TV.
2.   4:3LB: (mailbox): suitable for use with standard size 
TV. In widescreen playback format top and bottom 
of the screen will display a black band.
3.   4:3PS (full screen scan): suitable for use with stan-
dard size TV. In widescreen playback format remove 
left and right edges then adjust picture to fit full 
screen. 
Note:
▀■  Quality of playback is related to the aspect ratio of 
the disc. Some discs may not be able to be played on 
the screen size you choose. 
▀■  For discs that are only able to accommodate 4:3 
format it doesn’t matter what screen ratio you select: 
playback ratio will always be 4:3.
▀■  Selection of screen ratio should match actual screen 
ratio of TV being used. 
						

							
44  *  DVD Projector
English

USER CONTROLS

When you forget the old password, press the initial password “0000”.
NoteNote
 Password
The default setting is “Password is locked”, can’t choose “Rating” 
or revise the password. If need to select “Rating” to press the nu-
merical key and importing the initial password of the one machine: 
0000, then press the enter button to confirm. When you need to 
change the password, input the old password first, and then input 
the new password. (The effective password is 4 bits)
 Rating
The “Rating” or “Parental lock” option makes it possible to restrict 
viewing of certain sequences or entire films to specified age groups.
 Default
Choose “Restore” then “Enter” pressed, the display parameters on 
all menu will return to their factory default settings.
 Exit Setup
Exit this menu. 
						

							
DVD Projector  *  45
English

USER CONTROLS

Language Setup
 OSD Language
Select your preferred language for the on-screen display 
menu. 
 Audio Lang
Select the audio language
 Subtitle Lang
Select the subtitle language
 Menu Lang
Select your preferred language for DVD menu.
 Exit Setup
Exit this menu. 
						

							
46  *  DVD Projector
English

USER CONTROLS

Digital Setup
 SPDIF Out
Choose the appropriate Digital Audio settings for your equip-
ment as it only affect during the playback of DVD discs of the 
DVD player.
▀■  SPDIF/Off: Turn off the sound.
▀■  SPDIF/RAW: Select this function, when the player is con-
nected to Dolby Digital Decoder.
▀■  SPDIF/PCM: Select this function, when the player is not 
connected to Dolby Digital Decoder.
 Key
 Adjust the key of sound.
 Exit Setup
Exit this menu. 
						

							
DVD Projector  *  47
English

USER CONTROLS

Video Setup
  Brightness
Adjust the brightness of the image.
▀■  Press  to darken an image.
▀■  Press  to lighten an image.
 Contrast
Contrast controls the degree of difference between the light-
est and darkest parts of the picture. Adjusting the contrast 
changes the amount of black and white with an image.
▀■  Press  to decrease the contrast.
▀■  Press  to increase the contrast.
 Saturation
Adjust the color balance of red and green.
▀■  Press  to increase the amount of green in an image.
▀■  Press  to increase the amount of red in an image.
 Output Level
There are three factory presets optimized for various types of 
pictures: Normal, Enhanced, Dynamic and User.
 Exit Setup
Exit this menu. 
						

							
48  *  DVD Projector
English

MAINTENANCE

Speaker Setup
 Downmix
Depending on the audio channels you got on your audio sys-
tem. You may decide the Downmix of the channels, whether 
they are “LT/RT”, “Stereo” or “Off”.
 OP Mode
 ▀■  Line out: Carries on the linear compression to the input 
signal. The volume slightly suits the evening to use.
 D.R.C
 Dynamic rage decides the pitch of volume.  You may set 
them as “Full”, 6/8, 4/8, 2/8 or “Off”. To compress the high 
volume Dolby Digital movie, prevent the sudden high volume 
sound appeared.
 Dual Mono
Sets the way of audio output for Left and right audio. You 
may set them as the “Stereo”, “Mono L”, “Mono R” or “Mix 
Mono”. 
 Exit Setup
Exit this menu. 
						

							
DVD Projector  *  49
English

MAINTENANCE

Troubleshooting
If you experience a problem with your projector, please refer to 
the following information. If a problem persists, please contact 
your local reseller or service center.
Image Problems
 No image appears on screen:
  Ensure that all the cables and power cord are correctly and securely 
connected as described in the “Installation” section.
  Ensure that connector pins are not bent or broken.
  Check the [Power] or [Stand By] button is pressed.
  Make sure that the projection lamp has been securely installed. 
Please refer to the “Replacing the lamp” section.
  Ensure that you have removed the lens cap and that the projector is 
powered on.
 Partial, scrolling, or incorrectly displayed images:
  Press [Re-Sync] on the control panel.
  If using a PC:
For Windows 95, 98, 2000, XP:
1.  From the “My Computer” icon, open the “Control Panel” 
folder, and double click the “Display” icon.
2.   Select the “Settings” tab.
3.   Verify that your display resolution setting is lower than or 
equal to 1280 x 1024.
4.   Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will 
also need to change the monitor display you are using. Refer to 
the following steps.
5.   Verify the resolution setting is lower than or equal to 1280 x 
1024.
The Resync function 
can not be used when the DVD player is operational. 
NoteNote 
						

							
50  *  DVD Projector
English

MAINTENANCE

6.   Select the “Change” button under the “Monitor” tab.
7.   Click on “Show all devices.” Next, select “Standard monitor 
types” under the SP box; choose the resolution mode you need 
under the “Models” box.
8.   Verify that the resolution setting of the monitor display is 
lower than or equal to 1280 x 1024.
  If using a Notebook PC:
1.  First, follow the steps above to adjust resolution of the com-
puter.
2.  Press the toggle output settings. example: [Fn]+[F4]
  If you experience difficulty changing resolutions or your monitor 
freezes, restart all the equipment including the projector.
 The screen of the Notebook or PowerBook computer is not 
displaying your presentation:
If using a Notebook PC:
Some Notebook PCs may deactivate their own screens when 
a second display device is in use.  Each has a different way of 
reactivating. Refer to your computer’s documentation for detailed 
information.
 Image is unstable or flickering:
  Use “Tracking” to correct it. See page 34 for more information.
  Change the monitor color setting on your computer.
 Image has a vertical flickering bar:
  Use “Frequency” to make an adjustment. See page 34 for more 
information.
  Check and reconfigure the display mode of your graphics card to 
ensure compatibility.
Compaq=>   [Fn]+[F4]
Dell =>     [Fn]+[F8]
Gateway=>  [Fn]+[F4]
IBM=>    [Fn]+[F7]
Mac Apple: System Preference-->Display-->Arrangement-->Mirror display
Hewlett =>   [Fn]+[F4]Packard 
NEC=>     [Fn]+[F3]
Toshiba =>   [Fn]+[F5]