Optoma Projector Movietime Dv11 User Manual

							
DVD Projector  *  31
English

USER CONTROLS

Image-I
 Display Mode
There are many factory presets optimized for various types of 
images.
▀■  Cinema: For home theater.
▀■  sRGB: For standard PC colour. (best colour reproduction)
▀■  Vivid: For dynamic frame.
▀■  PC: For computer or notebook. (brightest image)
▀■  Game: For game.
▀■  User: Memorize user’s settings.
  Brightness
Adjust the brightness of the image.
▀■  Press  to darken an image.
▀■  Press  to lighten an image.
 Contrast
Contrast controls the degree of difference between the light-
est and darkest parts of the picture. Adjusting the contrast 
changes the amount of black and white with an image.
▀■  Press  to decrease the contrast.
▀■  Press  to increase the contrast.
  Color
Adjust a video image from black and white to fully saturated 
color.
▀■  Press  to decrease the amount of color in an image.
▀■  Press  to increase the amount of color in an image.
The “Color” sub menu is not supported under the analog RGB input source.
NoteNote 
						

							
32  *  DVD Projector
English

USER CONTROLS

 Tint
Adjust the color balance of red and green.
▀■  Press  to increase the amount of green in an image.
▀■  Press  to increase the amount of red in an image.
 Sharpness
Adjust the sharpness of an image.
▀■  Press  to decrease the sharpness.
▀■  Press  to increase the sharpness.
The “Tint” sub menu is not supported under the analog RGB input source.
NoteNote 
						

							
DVD Projector  *  33
English

USER CONTROLS

Image-II
  De gamma
This allows you to choose a degamma table that has been fine-
tuned to bring out the best image quality for the input.
 White Peaking
Use the white peaking control to set the white peaking level of the 
DMD chip.  “1” stands for minimal peaking, and “10” stands for 
maximum peaking.  If you prefer a stronger image, adjust toward 
the maximum setting.  For a smoother, more natural image, adjust 
toward the minimum setting.
 Color Temp.
Adjust the color temperature.  The range is from “0” to “2.”  At a 
higher temperature, the screen looks colder; at a lower tempera-
ture, the screen looks warmer.
 True Vivid
Use  or  to select Red, Green, or Blue for brightness (Offset) and 
contrast (Gain). 
						

							
34  *  DVD Projector
English

USER CONTROLS

 Signal
 
▀■  Frequency: Changes the display data frequency to match the 
frequency of your computer’s graphic card. When you expe-
rience a vertical flickering bar, use this function to make an 
adjustment.
▀■  Tracking : Synchronizes the signal timing of the display with 
the graphics card. If you experience an unstable or flickering 
image, use this function to correct it.
▀■  Horizontal: Adjusts the horizontal position. 
▀■  Vertical: Adjusts the vertical position. 
  Reset
Choose “Yes” then “Enter” pressed, the display parameters on this 
menu will return to their factory default settings.
The “Signal” sub menu is supported under the Analog RGB and Analog YPbPr input sources.
NoteNote 
						

							
DVD Projector  *  35
English

USER CONTROLS

Source480i/p576i/p720p1080iPC
4:3Scale to 800x600
16:9-IScale to 800x450
16:9-IIScale to 854x480, then center 800x480 image to 
display
Native1:11:1 800x720 
centered
960x540 
centered
1:1
  Format
▀■  4:3: The input source will be scaled to fit the projection-screen.
▀■  16:9-I: The standard wide-screen display format of the projector.
▀■  16:9-II: The non-standard wide-screen display format of the 
projector. Part of the original image will be cut if the image 
aspect ratio is less than 1.67:1.
▀■  Native: The input source will be displayed without scaling.
 Zoom
Provide different magnification ratios to zoom an image. Image 
will be centered after zooming.
 Image Shift
Shifts the projected image position vertically. 0 is middle of the 
screen.
 Overscan
Mask off a few pixels on each edge of the image to be displayed. 
Use this function to adjust if image source happens to have encod-
ing error near any edge of the displayable image.
Display 
						

							
36  *  DVD Projector
English

USER CONTROLS

 Keystone
Adjust image distortion caused by tilting projector. (±16 degrees)
  Reset
Choose “Yes” then “Enter” pressed, the display parameters on this 
menu will return to their factory default settings. 
						

							
DVD Projector  *  37
English

USER CONTROLS

 Menu Location
Choose the menu location on the display screen. 
  Projection
▀■    Front-Desktop 
The factory default setting.
▀■    Rear-Desktop
When you select this function, the projector reverses the image so 
you can project from behind a translucent screen.
▀■    Front-Ceiling
When you select this function, the projector turns the image upside 
down for ceiling-mounted projection.
▀■    Rear-Ceiling 
When you select this function, the projector reverses and turns the 
image upside down. You can project from behind a translu-cent 
screen with ceiling mounted projection.
 Signal Type
Select signal type RGB or Video sources.
 Source Lock
When this function is turned off, the projector will search for other 
signals if the current input signal is lost. When this function is 
turned on, it will search specific connection port.
 High Altitude
Choose “ON” to turn on High Altitude mode. Operates the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
System 
						

							
38  *  DVD Projector
English

USER CONTROLS

 DVD Setup
Press “Enter” to go to DVD menu.
 Mute
▀■  Choose the “On” to turn mute on.
▀■  Choose the “Off” to turn mute off.
 Reset
 Choose “Yes” then “Enter” pressed, the display parameters on this 
menu will return to their factory default settings. 
						

							
DVD Projector  *  39
English

USER CONTROLS

Lamp Setting
 Lamp Hour
Displays the cumulative lamp operating time.
 Lamp Reset
Reset the lamp setting only when the new lamp is replaced.
 Lamp Reminder
Choose this function to show or to hide the warning message when 
the changing lamp message is displayed. The message will show 
up 30 hours before end of life. 
						

							
40  *  DVD Projector
English

USER CONTROLS

How to Operate WMA/MP3/JPEG Program
1.   When you place the MP3/JPEG disc, the DVD player will automati-
cally detect the program.
2.   Prioritize to enter the first table of MP3 automatically. And play the 
first song under this file folder (Cursor suspend in “01” position) 
3.   Use   keys to select the function menu. And the marked icon 
will turn transparency into full color. 
4.   Use   keys to select the desired track. After the selected star, it 
will begin to flash.
5.   Press [Enter]/[Play] button to play.
6.   Press [Return] button to go back the program.
7.   To exit program, press [Menu]. 
Current Title
File Folder
Sliding Bar
JPEG Format
Play button
MP3/WMA Format
File list