Optoma Hd82 Projector User Manual

English


Installation
Due to the difference in applications for each country, some regions may have different ac-cessories.
1...............................................................RS232 Cable (Optional Accessory)
2....................................................................VGA Input Cable (Europe Only)
3....................................................................DVI Cable (Optional Accessory)
4..........................................................DVI/HDMI Cable...



Installation

Due to the difference in applications for each country, some regions may have different ac-cessories.
1...............................RCA Component Cable for YPbPr (Optional Accessory)
2.......................Composite Video Cable (Not Available in European Version)
3.............................................................S-Video Cable (Optional Accessory)
4...............................................SCART RGB/S-Video Adapter (Europe Only)...

English


Installation

POWER
TEMP
LAMPSTANDBY

Powering On the Projector
1. Remove the lens cap. 
2.  Securely connect the power cord and signal cable. When 
connected, the power led will turn red.
3.  Turn on the lamp by pressing 
“” button on the side of the 
projector or on the remote control. The power led will now 
flash blue. 
  The startup screen will display in approximately 30 seconds. 
The first time you use the projector, you can select your 
preferred language from quick menu...



Installation

Warning Indicator
▀■ When the “LAMP” indicator led is lit orange, the projector will 
automatically shut down. Please call the nearest Optoma 
facility for assistance. 
▀■  When the “TEMP” indicator turns red, it indicates the projec-
tor has overheated. The projector will shut down automati-
cally. 
Under normal conditions, the projector can be switched on 
again after it has cooled down.
▀■  When the “TEMP” indicator flashes red, it indicates the fan 
has failed.
Powering Off...

English


Installation

Adjusting the Projected Image
Adjusting the Projector’s Height
Tilt-Adjustment Feet
The projector is equipped with elevator feet for adjusting 
the image height.
 To raise the image:
Use screw in foot to raise the image to the desired height 
angle and ine-tune the display angle . 
 To lower the image:
Use screw in foot to lower the image to the desired height 
angle and ine-tune the display angle . 
1      



Installation
Horizontal Lens 
Shift Lever
Adjusting Projected Image Position 
Using PureShift
The PureShift feature provides a lens shift function that can be 
used to adjust the position of the projected image either hori-
zontally or vertically within the range detailed below. PureShift 
is a unique system that provides lens shift while maintaining 
a much higher ANSI contrast ratio than traditional lens shift 
system.
Vertical Lens Shift Lever
▀■ Adjusting the vertical image position
The...

English


User Controls
Screen Height
(H)100%
5%
30%Distance(L)
Screen
Maximum Shift
25%
15%W15%WLeft SideRight Side
Screen Width(W)
130%(V), 0%(H)
-15%(H)15%(H)105%(V)
UP/DOWNRIGHT/LEFT
HH x 15%
V
H x 15%
V
V x 25%
Offset max=V x 30%
Offset min=V x 5%
▀■ Adjusting the horizontal image position
With the lens in the centre position the horizontal image position 
can be adjusted to the left or right by up to a maximum of 15% 
of the image width. Note that the maximum horizontal image 
height...



User Controls

	This graph is for user’s reference only.
Diagonallength (inch) size of 16:9 Screen
Screen Size W X H (16:9)Projection distance...

English


User Controls

I m a g e - S h i ft
M e nuM o de
E d geM a skO v e r s c an
1 6 :9
4 :3L e t t e r - B ox
N a t i ve
H D M l1H D M l2
S -Vi d eoVi d eoY P b Pr
D VI
/
R e - S y nc
V GA
S c r e enUPD O WN
B r i g h t n e ssP o w erO ff
P o w erOn
C o n t r a s tP u r e E n g i n e
DBB r i teM o de
P U R E

Using the Remote Control
 Power OnRefer to the “Power On the Projector” 
section on page 13.
 BrightnessAdjust the brightness of the image.
 Power OffRefer to the “Power Off the...

20

User Controls

Edge MaskChoose “On” to mask off a few pixels on 
each edge of the image to be displayed. 
Use Edge Mask “On” if image source 
happens to have encoding error near any 
edge of the displayable image.
UpUse this button to screen up.
DownUse this button to screen down.
 4:3Scale the image at a 4:3 aspect ratio.
 Letter BoxEnable the viewing of the letterboxed 
nonanamorphically enhanced movie at 
full screen width. Part of the original im-
age will be lost if the image aspect ratio is...