Optoma Hd82 Projector User Manual

							
English


Installation
Due to the difference in applications for each country, some regions may have different ac-cessories.
1...............................................................RS232 Cable (Optional Accessory)
2....................................................................VGA Input Cable (Europe Only)
3....................................................................DVI Cable (Optional Accessory)
4..........................................................DVI/HDMI Cable (Optional Accessory)
5.........................................................................\
...........................Power Cord
NoteNote
AB12V TRIGGERVIDEOS-VIDEORS232Y/GPb/BPr/RVGA/SCARTDVI-DHDMI 1HDMI 2v1.3  with Deep Color
E62405SPR
 VGA,DVI
 VGA,DVI
Connecting the Projector
4
5
12
3
Connect to Notebook/DVI/VGA-In        
						

							


Installation

Due to the difference in applications for each country, some regions may have different ac-cessories.
1...............................RCA Component Cable for YPbPr (Optional Accessory)
2.......................Composite Video Cable (Not Available in European Version)
3.............................................................S-Video Cable (Optional Accessory)
4...............................................SCART RGB/S-Video Adapter (Europe Only)
5....................................................................DVI Cable (Optional Accessory)
6.........................................................................\
...HDMI Cable (Europe Only)
7.........................................................................\
...........................Power Cord
NoteNote
AB12V TRIGGERVIDEOS-VIDEORS232Y/GPb/BPr/RVGA/SCARTDVI-DHDMI 1HDMI 2v1.3  with Deep Color
E62405SPR
DVD player, Set-top BoxHDTV receiver
DVD player, Set-top BoxHDTV receiver
Video Output
S-Video Output
Connecting the Projector
4
5
1
2
3
Connect to Video/SCART
6
7
12V Trigger B is pro-grammable trigger.
NoteNote        
						

							
English


Installation

POWER
TEMP
LAMPSTANDBY

Powering On the Projector
1. Remove the lens cap. 
2.  Securely connect the power cord and signal cable. When 
connected, the power led will turn red.
3.  Turn on the lamp by pressing 
“” button on the side of the 
projector or on the remote control. The power led will now 
flash blue. 
  The startup screen will display in approximately 30 seconds. 
The first time you use the projector, you can select your 
preferred language from quick menu after the startup screen 
display.
4.  Turn on your source that you want to display on the screen 
(computer, notebook, video player, etc). The projector will 
detect the source automatically and will display on the 
screen. If not, push menu button and go to “SETUP”. Make 
sure that the “Source Lock” has been set to “Off”.
▀■	If you connected multiple sources at the same time, press 
the “Source” key on the remote control to switch between 
inputs.
Powering On/Off the Projector
Turn on the projector first and then select the signal sources.POWERTEMPLAMPSTANDBY
1
NoteNote
2        
						

							


Installation

Warning Indicator
▀■ When the “LAMP” indicator led is lit orange, the projector will 
automatically shut down. Please call the nearest Optoma 
facility for assistance. 
▀■  When the “TEMP” indicator turns red, it indicates the projec-
tor has overheated. The projector will shut down automati-
cally. 
Under normal conditions, the projector can be switched on 
again after it has cooled down.
▀■  When the “TEMP” indicator flashes red, it indicates the fan 
has failed.
Powering Off the Projector
1.  Press the “  ” button on the remote control or “” button on 
the side of the projector two times with one second interval 
in between to turn off the projector. First push of button will 
display the following message on the screen. 
Press the button again to confirm the shut down. If the but-
ton is not pressed, the message will disappear in 5 seconds.
2.  The cooling fans continue to operate for about 60 seconds 
for cooling cycle and the Power LED will turn blue.  When 
the lights solid red, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until 
the projector has completed the cooling cycle and has en-
tered standby mode.  Once in standby mode, simply press “
” button to restart the projector.
3.  Disconnect the power cord from the electrical outlet and the 
projector.
4.  Do not turn on the projector immediately following a power 
off procedure.
Contact the nearest service center if the projector displays these symptoms. See page 49 for more information.
NoteNote      
						

							
English


Installation

Adjusting the Projected Image
Adjusting the Projector’s Height
Tilt-Adjustment Feet
The projector is equipped with elevator feet for adjusting 
the image height.
 To raise the image:
Use screw in foot to raise the image to the desired height 
angle and ine-tune the display angle . 
 To lower the image:
Use screw in foot to lower the image to the desired height 
angle and ine-tune the display angle . 
1      
						

							


Installation
Horizontal Lens 
Shift Lever
Adjusting Projected Image Position 
Using PureShift
The PureShift feature provides a lens shift function that can be 
used to adjust the position of the projected image either hori-
zontally or vertically within the range detailed below. PureShift 
is a unique system that provides lens shift while maintaining 
a much higher ANSI contrast ratio than traditional lens shift 
system.
Vertical Lens Shift Lever
▀■ Adjusting the vertical image position
The minimum vertical image offset is fixed at 5% of the image 
height above the centre of the projector lens. This can not be 
changed. The vertical image height can be adjusted between 
5% and 30% of the image height. Note that the maximum verti-
cal image height adjustment can be limited by the horizontal 
image position. For example it is not possible to achieve the 
maximum vertical image position height detailed above if the 
horizontal image position is at maximum. Please consult the 
PureShift Range diagram below for further clarification.      
						

							
English


User Controls
Screen Height
(H)100%
5%
30%Distance(L)
Screen
Maximum Shift
25%
15%W15%WLeft SideRight Side
Screen Width(W)
130%(V), 0%(H)
-15%(H)15%(H)105%(V)
UP/DOWNRIGHT/LEFT
HH x 15%
V
H x 15%
V
V x 25%
Offset max=V x 30%
Offset min=V x 5%
▀■ Adjusting the horizontal image position
With the lens in the centre position the horizontal image position 
can be adjusted to the left or right by up to a maximum of 15% 
of the image width. Note that the maximum horizontal image 
height adjustment can be limited by the vertical image position. 
For example it is not possible to achieve the maximum horizon-
tal image position if the vertical image position is at maximum. 
Please consult the PureShift Range diagram below for further 
clarification.
Screen Height
(H)100%
5%
30%Distance(L)
Screen
Maximum Shift
25%
15%W15%WLeft SideRight Side
Screen Width(W)
130%(V), 0%(H)
-15%(H)15%(H)105%(V)
UP/DOWNRIGHT/LEFT
HH x 15%
V
H x 15%
V
V x 25%
Offset max=V x 30%
Offset min=V x 5%              
						

							


User Controls

	This graph is for user’s reference only.
Diagonallength (inch) size of 16:9 Screen
Screen Size W X H (16:9)Projection distance (D)Offset(Hd)(m)(feet)(m)(feet)WidthHeightWidthHeightwidetelewidetele(m)(feet)300.660.372.181.23-1.51-4.970.110.37451.000.563.271.841.492.274.887.450.170.55501.110.623.632.041.652.525.438.280.190.61601.330.754.362.451.983.036.519.930.220.74701.550.875.082.862.323.537.6011.590.260.86801.771.005.813.272.654.048.6813.240.300.98901.991.126.543.682.984.549.7714.900.341.101002.211.257.264.093.315.0510.8516.550.371.231202.661.498.724.903.976.0513.0219.860.451.471503.321.8710.896.134.967.5716.2824.830.561.842004.432.4914.538.176.6110.0921.7033.110.752.453006.643.7421.7912.269.9215.1432.5549.661.123.68
Screen Height
(H)100%
5%
30%Distance(L)
Screen
Maximum Shift
25%
15%W15%WLeft SideRight Side
Screen Width(W)
130%(V), 0%(H)
-15%(H)15%(H)105%(V)
UP/DOWNRIGHT/LEFT
HH x 15%
V
H x 15%
V
V x 25%
Offset max=V x 30%
Offset min=V x 5%
▀■ PureShift Range Diagram
Adjusting Projection Image Size          
						

							
English


User Controls

I m a g e - S h i ft
M e nuM o de
E d geM a skO v e r s c an
1 6 :9
4 :3L e t t e r - B ox
N a t i ve
H D M l1H D M l2
S -Vi d eoVi d eoY P b Pr
D VI
/
R e - S y nc
V GA
S c r e enUPD O WN
B r i g h t n e ssP o w erO ff
P o w erOn
C o n t r a s tP u r e E n g i n e
DBB r i teM o de
P U R E

Using the Remote Control
 Power OnRefer to the “Power On the Projector” 
section on page 13.
 BrightnessAdjust the brightness of the image.
 Power OffRefer to the “Power Off the Projector” 
section on page 14.
 ContrastControl the degree of difference between 
the lightest and darkest parts of the 
picture.
PureEngineThe PureEngine is a collection of ad-
vanced image processing technologies 
that enhances the quality of the displayed 
image.
 DynamicBlackEnable the projector to automatically 
optimize the display of dark movie scenes 
enabling them to be shown in incredible 
detail. (refer to page 26)
/ Brite ModeIncrease the brightness of the image. 
(refer to page 34)
 Image-ShiftShift the projected image position verti-
cally.
EnterConfirm your item selection.
Four Directional 
Select Keys
Use directional select keys to select items 
or make adjustments to your selection.
 MenuDisplay or exit the on-screen display 
menus for projector.
 ModeSelect the display mode from Cinema,
Bright, Photo, Reference and User.
OverscanMask off a few pixels on each edge of the 
image to be displayed. Use the function 
to adjust if image source happens to have 
noise near any edge of the display image.
PowerOnOff
MENU
Re-SyncSourceImage Shift
Remote Control      
						

							
20

User Controls

Edge MaskChoose “On” to mask off a few pixels on 
each edge of the image to be displayed. 
Use Edge Mask “On” if image source 
happens to have encoding error near any 
edge of the displayable image.
UpUse this button to screen up.
DownUse this button to screen down.
 4:3Scale the image at a 4:3 aspect ratio.
 Letter BoxEnable the viewing of the letterboxed 
nonanamorphically enhanced movie at 
full screen width. Part of the original im-
age will be lost if the image aspect ratio is 
less than 2.35:1..
Re-SyncAutomatically synchronize the projector to 
the input source.
 16:9Scale the image at a 16:9 aspect ratio.
 NativeThe input source will be displayed without 
scaling.
VGAPress “VGA” to choose source from
VGA connector.
HDMI 1Press “HDMI 1” to choose source from 
HDMI 1 connector.
HDMI 2Press “HDMI 2” to choose source from 
HDMI 2 connector.
DVIPress “DVI” to choose Analog and Digital 
signal source from DVI connector.
YPbPrPress “YPbPr” to choose Component 
Video source.
S-VideoPress “S-Video” to choose S-video 
source.
VideoPress “Video” to choose Composite Video 
source.
SourcePress “Source” to choose DVI, RGB, 
Component, S-Video, Composite Video, 
and HDMI source.
I m a g e - S h i ft
M e nuM o de
E d geM a skO v e r s c an
1 6 :9
4 :3L e t t e r - B ox
N a t i ve
H D M l1H D M l2
S -Vi d eoVi d eoY P b Pr
D VI
/
R e - S y nc
V GA
S c r e enUPD O WN
B r i g h t n e ssP o w erO ff
P o w erOn
C o n t r a s tP u r e E n g i n e
DBB r i teM o de
P U R E
PowerOnOff
MENU
Re-SyncSourceImage Shift