Optoma Hd82 Projector User Manual

English


User Controls

 Menu Location
Choose the menu location on the display screen.
 Projection
   Front-Projection
This is the default selection. The image is projected straight on 
the screen.
   Rear-Desktop 
When selected, the image will appear reversed.
   Front-Ceiling 
When selected, the image will turn upside down.
   Rear-Ceiling 
When selected, the image will appear reversed in upside down 
position.
  Image AI
Image AI improves the contrast of the picture by optimizing the...



User Controls

 On: The dynamic image performance manager is active in mak-
ing sure your greatest pleasure from seeing a movie dynami-
cally with the most dark details revealed, vivid and bright image 
performed all the way.
 Off: The dynamic image performance manager is on standby.
 Test Pattern
Display a test pattern. There are Grid, White pattern and None.
 Background Color
Use this feature to display a “Dark Blue”, “Black”, or “Gray” screen 
when no signal is available.
 12V Trigger...

English


User Controls

 Off: disables the trigger.
 On: enables the trigger and the programmable sub-menu. The 
sub-menu is accessed by selecting the ON option then press-
ing the ENTER button on the remote control. Checking an op-
tion in the sub-menu will activate the trigger when the selected 
display mode is selected. In the example below 16:9 has been 
selected – this means that Trigger B will be active when the 
projector display mode is set to 16:9. The trigger will be inactive 
for...



User Controls

 Lamp Hour
Display the cumulative lamp operating time.
 Lamp Reminder
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed. The message will 
appear up 30 hours before suggested replacement of lamp.
 Bright Mode
Choose “On” to increase the brightness. Choose “Off” to return 
normal mode.
 Lamp Reset
Reset the lamp life hour after replacing the lamp.
System | Lamp 
Settings      

English


User Controls

 Language
Choose the multilingual OSD menu. Press  or   into the sub 
menu and then use the   or  key to select your preferred lan-
guage. Press “Select (Enter)” to finalize the selection.
 Input Source
Enable input sources. Press  or   into the next menu as below 
and then use  or  to select. Press “Select (Enter)” to finalize 
the selection. The projector will not search inputs that are de-se-
lected.
Setup      



User Controls

 Source Lock
When this function is turned off, the projector will search for other 
signals if the current input signal is lost. When this function is 
turned on, it will search for a specified connection port.
 High Altitude
Choose “On” to turn on High Altitude mode. Operates the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
 Auto Power Off
Set the interval of power-off of the system, if there is no signal
input. (In minutes)....

English


User Controls

 White Level : Allow user adjust White Level when inputting 
SVideo or Video/CVBS signals.
 Black Level : Allow user adjust Black Level when inputting 
SVideo or Video/CVBS signals.
 Saturation : Adjust a video image from black and white to fully 
saturated color. Press the  to decrease the amount of color in 
the image. Press the  to increase the amount of color in the 
image.
 Hue : Adjust the color balance of red and green. Press the  
to increase the amount of...



Appendices

Image Problems
 No image appears on-screen
 Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
 Ensure the pins of connectors are not crooked or broken.
 Check if the projection lamp has been securely installed. Please 
refer to the “Replacing the Lamp” section.
 Make sure you have removed the lens cap and the projector is 
switched on.
 Image is out of focus
 Make sure the Lens cap is removed.
...

English


Appendices

 Image is too small or too large
 Adjust the zoom lever on the top of the projector.
 Move the projector closer to or further from the screen.
  Press [Menu] on the projector panel, go to “Display-->Format”. Try 
the different settings.
 Image has slanted sides:
 If possible, reposition the projector so that it is centered on the 
screen and below the bottom of the screen.
 Use “Display-->V Keystone” from the OSD to make an adjustment.
 Image is reversed
 Select...

0

Appendices

Projector Status Indication
 LED states
MessagePower LED(Red)Power LED(Blue)Temp-LED(Red)Lamp-LED(Orange)
Standby State (Input power cord)
Standby State(Burn in mode)Flashing
Power on and Lamp lighting* 
Power off (Cooling)
Error (Lamp fail)
Error (Thermal fail)
Error (Fan fail)Flashing
Error (Over Temp.)
Steady light => No light => 
NoteNote
 * Power LED be ON when OSD appears, be OFF when OSD disappears. 
POWERTEMPLAMP
STANDBYPOWER
TEMP
LAMP
STANDBY