Optoma Hd67n Projector User Manual

English
11
Installation
Connecting the Projector
	Due to the difference in applications for each country, some regions may have different accessories.
	(*) Optional accessory 
Connect to Computer/Notebook
1....................................................................................................Power Cord2...................................................................................................*VGA...

1212
Installation
VGA-IN / SCART / YPbPrHDMIS-VIDEOVIDEORS-232AUDIO-INAUDIO-OUT
E62405SPR
Connect to Video Sources
1....................................................................................................Power Cord2.............................................................................*VGA to component Cable3.............................................................................*3 RCA Component...

English
13
Installation
Powering on the Projector
1.  Remove the lens cap. 
2. Securely connect the power cord and signal cable. When 
connected, the Power LED will turn red.  
3.  Turn on the lamp by pressing “POWER” button either on the  top of the projector or on the remote. The Power LED will 
now turn Green. 
  The startup screen will display in approximately 10 seconds.  The fi rst time you use the projector, you can select your 
preferred language after the startup screen displays.
4.  Turn on...

1414
Installation
Powering off the Projector
1.  Press the “POWER” button to turn off the projector lamp. 
The following message will be displayed on the screen. 
  Press the “POWER” button again to confirm, otherwise the 
message will disappear after 15 seconds. 
When you press the “POWER” button a second time, the 
system will show the countdown timer on the screen.
2. The cooling fans continue to operate for about 10 seconds 
for cooling cycle. When the Power LED turns Red, the 
projector has entered...

English
15
Installation
 
Adjusting the Projected Image
Adjusting the Projector’s Height 
The projector is equipped with elevator feet for 
adjusting the image height.
1. Locate the adjustable foot you wish to modify on the underside of the projector. 
2. Rotate the adjustable ring counter clockwise to raise  the projector or clockwise to lower it. Repeat with the 
remaining feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Adjusting the Projector’s Zoom / Focus
Focus RingZoom Ring
You may turn...

1616
Installation
Adjusting Projection Image Size
Width
Height
Diagonal
Top View
Side View Projection Distance (D)
Projection Distance (D) Screen
Screen
Screen (W)
Screen (H)
Offset (Hd)
 This graph is for user’s reference only.
Diagonal length (inch) size of 16:9 Screen
Screen Size W x HProjection Distance (D)Offset (Hd)(m)(feet)(m)(feet)
WidthHeightWidthHeightwidetelewidetele(m)(feet)
26.57 0.59 0.33 1.94 1.08 -1.0-3.28 0.04 0.13 
30.00 0.66 0.37 2.16 1.21 1.01.13.28 3.61 0.05 0.15 
40.00 0.89 0.50...

English
17
User Controls
Control Panel
 
Control Panel & Remote Control
There are two ways for you to control the functions: 
Control Panel and Remote Control.
Using the Control Panel
POWERRefer to the “Power On/Off the Projector” section on 
pages 13-14.
MENUPress “MENU” to launch the on-screen display 
(OSD) menu. To exit OSD, Press “MENU” again.
Confi rm your item selection.
RE-SYNCAutomatically synchronize the projector to the input 
source.
SOURCEPress “SOURCE” to select an input signal.
Four...

1818
User Controls
Remote Control
Lamp
3D InvertVGA
Using the Remote Control
Power OnRefer to the “Power On” section on page 13.
Power OffRefer to the “Power On/Off the Projector” 
section on page 14.
Lamp ModeIncrease the brightness of the image. (refer 
to page 40)
ModeSelect the display mode from Cinema, 
Bright, Photo, Reference and User.
4:3Scale the image at a 4:3 aspect ratio.
16:9Scale the image at a 16:9 aspect ratio.
LBX
Enable the viewing of the letterboxed nonan-
amorphically enhanced movie...

English
19
User Controls
Lamp
3D InvertVGA
Using the Remote Control
EnterConfi rm your item selection.
SourcePress “Source” to select an input 
signal.
Re-syncAutomatically synchronizes the pro-
jector to the input source.
MenuDisplay or exit the on-screen display 
menus for projector.
HDMIPress “HDMI” to choose source from 
HDMI connector.
VGAPress “VGA” to choose source from 
VGA/SCART/YPbPr connector.
S-VideoPress “S-Video” to choose S-Video 
source.
VideoPress “Video” to choose Composite 
video...

2020
User Controls
The Projector has multilingual On-screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “MENU” on the Remote Control or Projector Keypad.
2  When OSD is displayed, use    keys to select any item in the 
main menu. While making a selection on a particular page, press  
 or “Enter” key to enter sub menu.
3. Use   keys to select the desired item...