Optoma Hd67n Projector User Manual

English
31
User Controls
  3D Mode
  Off: Select “Off” to turn 3D settings off for 3D images.
  DLP Link: Select “DLP Link” to use optimized settings for DLP 
Link 3D images.
  IR: Select “IR” to use optimized settings for IR-based 3D 
images.
  3D Sync. Invert
 Press the “On” to invert left and right frame contents.
 Press the “Off” for default frame contents. 
	“IR” options may vary according to model.
	“3D Sync Invert” is only avail-able when 3D is enabled and this mode 3D is for DLP link glass...

3232
User Controls
SETUP
  Language
Choose the multilingual OSD menu. Press  or  into the sub 
menu and then use the 
 or  key to select your preferred 
language. Press “Enter” to fi nalize the selection. 
  Projection
     Front-Desktop
This is the default selection. The image is projected straight on 
the screen.
 
    Rear-Desktop
When selected, the image will appear reversed.
 
    Front-Ceiling 
When selected, the image will turn upside down. 

English
33
User Controls
	Rear-Desktop and 
Rear-Ceiling are 
to be used with a 
translucent screen.
NoteNote     Rear-Ceiling 
When selected, the image will appear reversed in upside down 
position.
  Menu Location
Choose the menu location on the display screen.
  Projector ID
ID defi nition can be set up by menu (range 0~99), and allow user 
control an individual projector by RS232. Refer to page 48 for the 
complete list of RS232 commands.
  Mute  
Choose the “On” to turn mute on. 

 Choose the...

3434
User Controls
SETUP | Signal -RGB Source
  Automatic
Automatically selects the singal. If you use this function, the 
Phase, frequency items are grayed out, and if Signal is not auto-
matic, the phase, frequency items will appear for user to manually 
tune and saved in settings after that for next time projector turns 
off and on again.
  Phase
Synchronize the signal timing of the display with the graphic card. 
If the image appears to be unstable or fl ickers, use this function to 
correct it....

English
35
User Controls
SETUP | Signal -Video Source
  Automatic
Automatically selects the singal. If you use this function, the 
Phase, frequency items are grayed out, and if Signal is not auto-
matic, the phase, frequency items will appear for user to manually 
tune and saved in settings after that for next time projector turns 
off and on again.
  Saturation
Adjust a video image from black and white to fully saturated color .
 
 Press the  to decrease the color saturation in the image.
 
 Press the...

3636
User Controls
OPTIONS 
 Source Lock
 On: The projector will only search current input connection.
 Off: The projector will search for other signals if the current input signal is lost. 
  High Altitude
When “On” is selected, the fans will spin faster. This feature is 
useful in high altitude areas where the air is thin.
 Information Hide
 On: Choose “On” to hide the info message.
 Off: Choose “Off” to show the “searching” message.
 Background Color
Use this feature to display a “Black”, “Red”,...

English
37
 Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, 
when there is no signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
 Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start, 
with or without a signal being sent to the projector. The projector 
will automatically power off when the countdown has finished (in 
minutes).
User Controls
OPTIONS | 
Advanced 

3838
User Controls
OPTIONS |  
Lamp Settings
 Lamp Hours
Display the projection time.
 Lamp Reminder
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed.  
The message will appear 30 hours before suggested replacement 
of lamp.
 Brightness Mode
 STD: Choose “STD” to dim the projector lamp which will lower 
power consumption and extend the lamp life. 
 BRIGHT: Choose “BRIGHT” to increase the brightness. 
 Lamp Reset
Reset the lamp hour counter after...

English
39
Appendices
Image Problems
 No image appears on-screen
 Ensure all the cables and power connections are correctly and 
securely connected as described in the “Installation” section.
 Ensure all the pins of connectors are not bent or broken.
 Check if the projection lamp has been securely installed. Please 
refer to the “Replacing the lamp” section.
 Make sure you have removed the lens cap and the projector is 
switched on.
 Ensure that the “AV mute” feature is not turned on.
 Image is out...

4040
Appendices
 Please setup the display format as 16:9 (wide) aspect ratio type 
on your DVD player.
 Image is too small or too large
 Adjust the Zoom Ring on the top of the projector.
 Move the projector closer to or further from the screen.
 Press “MENU” button on the remote control or projector panel, go 
to “DISPLAY  Format” and try the different settings.
 Image has slanted sides
 If possible, reposition the projector so that it is horizontally 
centered on the screen and below the bottom of...