OKI C530dn User Manual

51 – C330/C530 Menu Functions
PPR Emulation Menu  
ITEMACTIONEXPLANATION
CHARACTER 
PITCH10 CPI; 
12 CPI;
 
17 CPI; 20 
CPI; 
PROPORTI
ONAL
Specifies character pitch in IBM PPR emula-
tion.
FONT 
CONDENSE12CPI TO 
20CPI
 
12CPI TO 
12CPI
Specifies 12CPI pitch for Condense Mode.
CHARACTER 
SETSET-1 
SET-2
Specifies a character set.
SYMBOL SET IBM-437
(DEFAULT 
SYMBOL 
SET ONLY 
SHOWN)Specifies a symbol set.
LETTER O 
STYLEDISABLE 
ENABLE
Specifies the style that replaces 9BH with 
letter o and 9DH with a...

52 – C330/C530 Menu Functions
FORM LENGTH11 INCH
11.7 
INCH
12 INCH
Specifies the length of paper.
TOF POSITION0.0INCH 
~ 
1.0INCHSpecifies the distance of print from the top 
edge of the paper.
LEFT MARGIN0.0INCH 
~ 
1.0INCHSpecifies the distance of print from the left 
hand edge of the paper.
FIT TO LETTERDISABLE 
ENABLE
Sets the printing mode that can fit print 
data, equivalent to 11 inches (66 lines), in 
the LETTER-size printable area.
TE X T  H E I G H TSAME 
DIFF
Sets the height of a character....

53 – C330/C530 Menu Functions
FX Emulation Menu  Calibration
ITEMACTIONEXPLANATION
CHARACTER 
PITCH10 CPI; 
12
 CPI; 
17 CPI; 
20
 CPI; 
PROPOR
-
TIONAL
Specifies character pitch in this emulation.
CHARACTER 
SETSET-1 
SET-2
Specifies a character set.
SYMBOL SETIBM-437 
(Default 
Symbol 
Set only 
shown)
Specifies a symbol set.
LETTER 0 
STYLEDISABLE 
ENABLE
Specifies the style that replaces 9BH with 
letter o and 9DH with a zero
ZERO CHAR-
ACTER
NORMAL 
SLASHED
Sets the zero to be slashed or unslashed....

54 – C330/C530 Menu Functions
USB Menu
This menu controls the operation of the printer’s USB data 
interface.   
LEFT MARGIN0.0INCH 
~ 
1.0INCHSpecifies the distance of print from the left 
hand edge of the paper.
FIT TO LET-
TER
DISABLE 
ENABLE
Sets the printing mode that can fit print 
data, equivalent to 11 inches (66 lines), in 
the LETTER-size printable area.
TEXT HEIGHTSAME 
DIFF
Sets the height of a character.
SAME: Regardless of CPI, same height.
DIFF: As CPI, character heights vary....

55 – C330/C530 Menu Functions
Network Menu   
ITEMACTIONEXPLANATION
TCP/IPENABLE 
DISABLE
Enables or disables this network protocol.
IP VERSIONIP v4 
IP v4+v6
IP v6
Sets up the IP version.
Operates with IPv4 only (not valid with 
IPv6).
Operates with both IPv4 and IPv6.
Operates with IPv6 only (not valid with 
IPv4).
From this stage, if IPv6 only is set from UI, 
for example Telnet, “IP v6” appears as the 
value of IP Version on the operation panel. 
“IP v6” will disappear from the value if “IP 
v4” or...

56 – C330/C530 Menu Functions
FRAME TYPEAUTO / 
802.2 / 
802.3 / 
ETHER
-
NET II / 
SNAP
Selects the Ethernet MAC layer frame type.
Display Condition: Netware should be 
enabled.
IP ADDRESS 
SETAUTO / 
MANUALSpecifies whether IP address allocation is 
automatic (DHCP) or manually assigned.
IPV4 
ADDRESSxxx.xxx.x
xx.xxxCurrent assigned IP address. To change, 
press 
OK and use Menu buttons to incre-
ment 1st octet, then press OK again to 
move on to next octet. When 4th octet has 
been set, press 
OK...

57 – C330/C530 Menu Functions
NETWORK 
SCALENORMAL 
/ SMALLSelects network size.
When NORMAL is selected, printer can work 
effectively, even when connected to a HUB 
that has a spanning tree
feature. However, printer start up time gets 
longer when computers are connected with 
two or three small LANs.
When SMALL is selected, computers can 
cover from two or three small LANs to a 
large LAN, but may not work effectively 
when connected to a HUB that has a span
-
ning tree feature.
HUB LINK 
SETTINGAUTO...

58 – C330/C530 Menu Functions
Memory Menu  
Sys Adjust menu   
ITEMACTIONEXPLANATION
RECEIVE BUF 
SIZEAUTO
0.5MB
1MB
2MB
4MB
8MB
16MB
32MB
Sets the size of the receive buffer.
RESOURCE 
SAVEAUTO
OFF
0.5MB
1MB
2MB
4MB
8MB
16MB
32MB
Sets the size of the resource saving area.
ITEMACTIONEXPLANATION
X ADJUST+2.00MIL
LIMETER
~
0.00MILL
IMETER
 
~
-
2.00MILLI
METER
Adjusts the position of a whole print image 
in the direction perpendicular to the direc
-
tion the paper runs, that is horizontally, in 
0.25 mm...

59 – C330/C530 Menu Functions
Y ADJUST+2.00MIL
LIMETER
~
0.00MILL
IMETER
 
~
-
2.00MILLI
METER
Adjusts the position of a whole print image 
in the direction the paper runs, that is verti
-
cally, in 0.25 mm increments.
Any parts of the print image that are outside 
the printable area as a result of this shift will 
be cropped.
Corrections in a negative value are ignored 
in PS mode.
DUPLEX X 
ADJUST+2.00MIL
LIMETER
~
0.00MILL
IMETER
 
~
-
2.00MILLI
METER
When printing the reverse page of a duplex 
job,...

60 – C330/C530 Menu Functions
Maintenance Menu  
ITEMACTIONEXPLANATION
MENU RESETEXECUTEResets menus to default settings.
SAVE MENUEXECUTESaves the current menu settings. The last 
menu executed is saved and the menu pre
-
viously saved is overwritten and erased.
When you press the OK button, the following 
confirmation message is displayed.
ARE YOU SURE? YES/NO
If you select NO, the display returns to the 
previous menu.
If you select YES, the current menu settings 
are stored and the menu is exited....