OKI C130n User Manual

151 - C130n User’s Guide
If the problem is not resolved, even after all of the above have been 
performed, contact Technical Support with the error information.
The color has a 
poor reproduction 
or has poor color 
density.The imaging cartridge 
may be defective.Remove the imaging cartridge and 
check for damage. If it is damaged, 
replace it.
Perform AIDC. (On the control panel 
menu, go to 
MAIN MENU/QUALITY 
MENU/AIDC/REQUEST AIDC
, then 
select 
YES.)
Symptom Cause Solution
Downloaded From...

152 - C130n User’s Guide
Status, Error, and Service Messages
Status, error, and service messages are displayed in the control panel 
message window. They provide information about your printer and help you 
locate problems. When the condition associated with a displayed message is 
corrected, the message is cleared from the window.
Standard Status Messages
MessageMeaningWhat to Do
CALIBRATINGWhenever you replace a toner 
cartridge or reboot the printer 
after making environmental 
changes, the printer...

153 - C130n User’s Guide
Error Messages: Warning 
PROCESSINGThe printer is processing data.No action needed.
Oki C130 
STARTING PRINTER
The printer is being started up.
PORT AUTH ACTIVEThe IEEE802.1x port is being 
authorized.
WARMING UPThe printer is warming up.
MessageMeaningWhat to Do
CHECK TRAY1 
PAPER 
(Displaying alternately)  
PRESS  
MENU/SELECT
Tray 1 is empty.Load the media into 
Tray
 1, and then press 
the Enter key.
Media has misfed in 
Tray
 1.
Remove the misfed 
media.
I/C ENDThe imaging...

154 - C130n User’s Guide
Error Messages (Operator Call)
X TONER LOWThe X toner cartridge 
is nearly empty.Prepare the specified 
color toner cartridge.
X TONER OUT
(Ready Indicator: On. 
Attention Indicator: Off)
The X toner cartridge 
is empty.Replace the toner 
cartridge.
#$Printing can 
continue, 
however, the 
printing results 
are not 
guaranteed.
MessageMeaningWhat to Do
AUTH 
TIMEOUT
The user is automatically 
logged off due to IEEE802.1x 
port authorization.Reauthorize the IEEE802.1x 
port, and...

155 - C130n User’s Guide
PAPER JAM 
DUPLEX
Media has misfed in the 
duplex option.Locate and remove the 
misfeed.
PAPER JAM 
EXIT
Media has misfed in the fuser 
area.
PAPER JAM 
FUSER
PAPER JAM 
TRANSFER
Media has misfed in the 
transfer roller area. This type 
of misfeed means that the 
media did not make it to the 
paper exit area.
PAPER JAM 
TRAY 2
Media has misfed while being 
pulled from Tray 2.Locate and remove the 
misfeed.
PUT 
SIZE 
TYPE 
IN TRAY 1
The size of paper being 
printed on is...

156 - C130n User’s Guide
Service Messages
These messages indicate a more serious error that can only be corrected by 
a customer service engineer. If one of these messages appears, turn the 
printer off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.
  
X TONER 
MISSING
The X toner cartridge is not 
installed.Install a X toner cartridge.
X TONER 
OUT
(Ready 
Indicator: Off. 
Attention 
Indicator: On)
The X toner cartridge is empty.Replace the...

157 - C130n User’s Guide
Installing 
Accessories
Downloaded From ManualsPrinter.com Manuals 

158 - C130n User’s Guide
Introduction
There are two options for this printer:
Second Paper Tray, which takes 500 sheets of 20-lb (75 g/m2) paper
Duplexer, for printing on both sides of the paper.
The duplexer is furnished with a duplex attachment which is required if the 
optional second tray is not installed.
Important!
Installing accessories always requires that the printer be turned off 
and unplugged during installation.
Tray 2 
If Tray 2 is installed, up to 500 additional sheets of A4/Letter-size...

159 - C130n User’s Guide
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Remove the dust cover from 
Tray
 1. 
3Close Tray 1 and the output tray 
 
 
 
 
 
 
 
 
 
 
 
4Unpack Tray 2.
NoteBe sure to place Tray 2 on a level surface.
Downloaded From ManualsPrinter.com Manuals 

160 - C130n User’s Guide
5Lift the printer and place it on top 
of Tray
 2, making sure that the 
positioning pins on Tray
 2 
correctly fit into the holes in the 
bottom of the printer.
6Open the output tray and 
Tray
 ,1.
7Reattach the dust cover.
Downloaded From ManualsPrinter.com Manuals