Oce CS2044 User Manual

31
Installing the Ink Tanks
4.Close the ink tank cover until you hear a click.[78] 
5.Repeat steps 1 to 4 to install the other ink tank colors.
6.Close the right back cover after you have installed all of the ink tank colors.[79] 
Downloaded From ManualsPrinter.com Manuals 

32 Chapter 1 Read this first
Loading Roll Media
Loading Roll Media
Attention: When you are handling roll media, it is recommended that you wear 
clean fabric gloves to protect the printing surface.
7.Raise the holder stopper lever (a) from the axle to unlock the holder stopper, and then 
remove the holder stopper from the roll holder.
[80] 
8.Position the roll so that the leading edge of media is at the bottom and facing away 
from you, then push the roll holder firmly into the media roll from the right...

33
Loading Roll Media
10.Open the top cover and then open the ejection guide.[83] 
11.Orient the roll holder with the front edge of the roll media facing you, then align the 
roll holder (b) with the left and right guide grooves (c) in the roll holder slot and 
insert the roll holder.
[84] 
bb c
c
Downloaded From ManualsPrinter.com Manuals 

34 Chapter 1 Read this first
Loading Roll Media
12.Pull out the leading edge of the roll media keeping both left and right sides level, and 
insert the media into the paper feed slot (d), and feed the paper until it reaches the 
paperweight (e).
[85] 
Once the media reaches the paperweight, it is automatically fed through to the 
platen.
13.Close the ejection guide.[86] 
14.Grasp the center of the leading edge of the media and lift up the release lever.[87] 
e
d
Downloaded From ManualsPrinter.com Manuals 

35
Loading Roll Media
15.Gently pull on the center of the leading edge of the roll media as far as the ejection 
guide (f) and align the right edge of the media with the right edge of the paper 
alignment line (g), then lower the release lever.
[88] 
Attention: Do not pull strongly on the roll media when you align it with the 
paper alignment line. The roll media may not feed out straight in some cases.
16.Close the top cover.[89] 
[90] 
[90] Media Type is displayed.
You can load the types of media shown...

36 Chapter 1 Read this first
Loading Roll Media
[3] 
17.Press [ ] or [ ] button to select the type of roll media you loaded, then press the 
OK button.
[91] 
[92] 
An equals = mark is displayed to the left of the option to show the media type that 
has been selected, and the printer begins preparing to feed the roll media.
Océ Media nameName Printer Operating Panel
IJM005 Océ Draft Paper  Draft Paper 
IJM020 Océ Standard Paper   Standard Paper 
IJM113 Océ Premium Paper 90g/m2  Premium Paper 
IJM150 Océ...

37
Loading Roll Media
Attention: Always set the Media Type setting to the type of roll media loaded 
in the printer.If the media type setting does not match the loaded roll media, 
printing quality may be reduced.
18.Press the [ ] or [ ] button to select the setting for the roll media length, and then 
press the OK button.
[93] 
[94] 
When the printer has finished preparing to feed the roll media, Online is displayed 
on the printer display and the printer is ready to print.
Roll Length Set
 30.0m...

38 Chapter 1 Read this first
Adjusting the Print Status
Adjusting the Print Status
Adjusting the Printhead Position
Note: It is recommended that you run the printhead adjustment using the type of 
media that you use most frequently.
Note: If you are using cut sheets, load at least one sheet of unused A3 or larger 
paper (not the blank side of used paper) in landscape orientation.
19.Press the Online button to display MAIN MENU on the printer display.[95] 
[96] 
20.Press the [ ] or [ ] buttons to select...

39
Adjusting the Print Status
22.Select Advanced Adj. then press the [ ] button.[101] 
[102] 
23.Press the [ ] or [ ] button to select Ye s, then press the OK button.[103] 
[104] 
The printhead adjustment pattern is printed.[105] 
The printer scans the resulting printout as it is printed, and automatically calibrates 
the printhead adjustment values.
When the calibration has finished, the printer returns online.
Printhead Adj
Advanced Adj.
Advanced Adj.
 Yes
Downloaded From ManualsPrinter.com Manuals 

40 Chapter 1 Read this first
Adjusting the Print Status
Media Feed Adjustment
Attention: Before you adjust the amount of media feed, you need to configure 
the media type setting using the operation panel to match the media loaded in the 
printer. If the media type selection does not match the media loaded in the printer, 
you will not achieve the correct print results and the printing quality will be 
reduced.
24.Press the Online button to display MAIN MENU on the printer display.[106] 
[107] 
25.Press...