Oce CS2044 User Manual

21
Removing the Packing Material
4.Remove the belt stopper (c) screws, and then remove the warning card that is 
attached by string, and the belt stopper.
[55] 
Note: The Belt Stopper, screw and hex driver are needed for transporting the 
printer.Store the Belt Stopper that you removed and the tools, etc. carefully in a safe 
place.
5.Open the ejection guide.[56] 
c
Downloaded From ManualsPrinter.com Manuals 

22 Chapter 1 Read this first
Removing the Packing Material
6.Remove the Roll Holder and remove the tape and packing material that is attached 
to the Roll Holder.
[57] 
7.Attach the four spool prevention stays (d) to the back of the ejection guide.[58] 
8.Close the ejection guide, and then close the top cover.[59] 
d d
Downloaded From ManualsPrinter.com Manuals 

23
Removing the Packing Material
9.Attach the Accessory Pocket to the left side of the rear surface of the printer.[60] 
This completes the printer assembly.
Downloaded From ManualsPrinter.com Manuals 

24 Chapter 1 Read this first
Connecting the Power
Connecting the Power
1.Connect the power cable to the power supply connector in the left side of the printer.[61] 
2.Insert the power plug into the outlet. The shape of the power cable varies from 
country to country.
[62] 
Downloaded From ManualsPrinter.com Manuals 

25
Installing the Printhead
Installing the Printhead
1.If the printer is off, press the Power button to switch the printer on.[63] 
2.Open the top cover.[64] 
Attention: Do not touch any areas other than as directed under any 
circumstances. Doing so may damage the printer.
3.Pull the printhead fixer lever towards you as far as it will go.[65] 
4.Pull the printhead fixer cover up as far as it will go.[66] 
Information Power
Cleaning
(3sec)
Printer Setup
Open UpperCover
Downloaded From ManualsPrinter.com...

26 Chapter 1 Read this first
Installing the Printhead
5.Hold the printhead by the grips (a) and remove it from the case, then remove the 
protective orange cap 1 (b).
[67] 
6.Push the tabs (d) on either side of printhead protective cap 2 (c) as shown in the 
diagram, and pull down to remove the cap.
[68] 
[69] 
[69] Do not touch the nozzles (e) or the electrical contacts (f)
Attention: The printhead contains protective nozzle ink. If ink leaks, it may soil 
the printer or peripherals. It is recommended...

27
Installing the Printhead
Attention: When you are handling the printhead, always hold it by the grips (a) 
on the left and right sides.
Attention: Do not touch the nozzles (e) or the electrical contacts (f) under any 
circumstances. Doing so may damage the printhead or cause printing problems.
Attention: Never try to re-attach the protective caps or packing material that you 
removed from the printhead.Dispose of these parts in accordance with local 
garbage disposal regulations.
7.Insert the printhead...

28 Chapter 1 Read this first
Installing the Printhead
9.Push the printhead fixer lever toward the back of the printer and then press down 
until you hear it click.
[72] 
10.Close the top cover.[73] 
Downloaded From ManualsPrinter.com Manuals 

29
Installing the Ink Tanks
Installing the Ink Tanks
1.Open the right back cover.[74] 
2.Press the ink tank lever of the color you are loading to open the ink tank cover.[75] 
3.Gently shake the ink tank 7 or 8 times while it is still in the bag before removing it 
from the bag. Insert the ink tank into the ink tank holder with the ink supply port 
facing down and the color label facing away from you.
[76] 
[77] 
[77] Attention
Bk Bk
bca
Downloaded From ManualsPrinter.com Manuals 

30 Chapter 1 Read this first
Installing the Ink Tanks
Attention: When you are handling an ink tank, always hold it by the grips (a) on 
the left and right sides.
Attention: Do not touch the ink supply port (b) or the electrical contacts (c) 
under any circumstances. Doing so may cause printing problems or stain the 
surrounding.
Downloaded From ManualsPrinter.com Manuals