Oce CS2044 User Manual

11
Unpack and Make Sure You Have Everything
[26] Output Stacker Arms L and R
[27] Output Stacker
[28] Rod Holders (x 2)
[29] ■M4 Hex Driver 
■M8 Hex Driver
[30] Stand Extension Boards L and R
[31] M4 Hex Screws (x 18)
Downloaded From ManualsPrinter.com Manuals 

12 Chapter 1 Read this first
Unpack and Make Sure You Have Everything
Installation Space
When you are installing the printer, reserve a space of the following dimensions or 
larger.
[32] 
[32] Height[33] 
[33] Width and Depth
m m 5 9 3 1
m m 0 2 3
2042 mm
1     1
1
  4
Downloaded From ManualsPrinter.com Manuals 

13
Assembling the Stand
Assembling the Stand
Caution: Have at least 2 people work on assembling the stand. Attempting 
this work alone may cause personal injuries or warp the stand.
1.Insert the right side of Stand Lower Stay (b) all the way into the hole in the side of 
Stand Leg R (a), and insert the left side of Stand Lower Stay all the way into the hold 
in the side of Stand Leg L (c).
[34] 
2.Securely affix Stand Lower Stay (b) to Stand Leg R (a) and Stand Leg L (c) using 5 
hex screws in each...

14 Chapter 1 Read this first
Assembling the Stand
4.Remove the tape that is attached the left and right sides of Stand Upper Stay (d).[37] 
5.Arrange the Stand Upper Stay so that the bends in the brackets on the left and right 
side (e) are facing up, and the side marked with an R is facing the Stand Leg R (a). 
Insert the Stand Upper Stay into the groove between Stand Leg R (a) and Stand Leg 
L (c).
[38] 
6.Securely fasten the hex screws on the left and right side using the supplied M8 hex 
driver to...

15
Assembling the Stand
7.Place the Stand in the installation location and lock the front casters.[40] 
Downloaded From ManualsPrinter.com Manuals 

16 Chapter 1 Read this first
Installing the Printer
Installing the Printer
Illustration
[41] 
[42] 
1.Remove the box from the printer body and clear out the packing material from above 
the printer, then lift up the base of the printer one side at a time and clear out the 
packing material from under the printer.
[43] 
2.Fold and then peel off the double-sided tape (c) from the Stand Extensions Boards, 
then stick Stand Extension Board (e) to the side of Stand Leg R (d) and Stand 
Extension Board (g) to...

17
Installing the Printer
3.Have 4 people grasp the handholds in the base of the printer body, then align the side 
of the printer body (h) with the line on the Stand Extension Board (i) and put the 
printer on the stand.
[45] 
4.Remove Stand Extension Board (e) and (g) from the Stand Legs.
5.Securely affix the printer body to the stand using 2 hex screws on each side starting 
from the bottom of the stand backing plate.
[46] 
Downloaded From ManualsPrinter.com Manuals 

18 Chapter 1 Read this first
Attaching the Output Stacker
Attaching the Output Stacker
1.Insert the Rod Holders (c) into holes on the back of Stand Leg L (a) and Stand Leg 
R (b).
[47] 
2.Insert Output Stacker Arm L (e) and Output Stacker Arm R (f) into the grooves (d) 
in the left and right ends of the Stand Upper Stay, then attach them using 2 hex 
screws.
[48] 
3.Stretch out the Output Stacker fabric such that the white mark (g) on the fabric is at 
the front right, and the center Output Stacker Rod...

19
Attaching the Output Stacker
4.Attach the Output Stacker Rod (j) in the center of the Output Stacker fabric to the 
Rod Holder (i), and loop the hole in the fabric (k) over the hook (l) above the Rod 
Holder.
[50] 
Attention: Attach the Output Stacker Rods to the Rod Holders in front of the 
Output Stacker Arm and at the very back of the Rod Holder. If the Output Stacker 
Rods are attached to the second rod holder from the back, the media will not 
enter the Output Stacker when ejected, and may cause...

20 Chapter 1 Read this first
Removing the Packing Material
Removing the Packing Material
1.Removing the tape and packing material that is attached to the printer body.[52] 
2.Open the top cover.[53] 
3.Lift up Release Lever (a) and remove the protective sheet (b) from the Platen, then 
lower the Release Lever.
[54] 
a
b
Downloaded From ManualsPrinter.com Manuals