Oce CS2044 User Manual

							11
Unpack and Make Sure You Have Everything
[26] Output Stacker Arms L and R
[27] Output Stacker
[28] Rod Holders (x 2)
[29] ■M4 Hex Driver 
■M8 Hex Driver
[30] Stand Extension Boards L and R
[31] M4 Hex Screws (x 18)
Downloaded From ManualsPrinter.com Manuals 
						

							12 Chapter 1 Read this first
Unpack and Make Sure You Have Everything
Installation Space
When you are installing the printer, reserve a space of the following dimensions or 
larger.
[32] 
[32] Height[33] 
[33] Width and Depth
m m 5 9 3 1
m m 0 2 3
2042 mm
1     1
1
  4
Downloaded From ManualsPrinter.com Manuals 
						

							13
Assembling the Stand
Assembling the Stand
Caution: Have at least 2 people work on assembling the stand. Attempting 
this work alone may cause personal injuries or warp the stand.
1.Insert the right side of Stand Lower Stay (b) all the way into the hole in the side of 
Stand Leg R (a), and insert the left side of Stand Lower Stay all the way into the hold 
in the side of Stand Leg L (c).
[34] 
2.Securely affix Stand Lower Stay (b) to Stand Leg R (a) and Stand Leg L (c) using 5 
hex screws in each side.
[35] 
3.Have 2 people grasp the stand from the left and right sides, and lift both sides of the 
stand simultaneously.
[36] 
Attention: When you are lifting the stand, make sure that you lift both sides at 
the same time. Lifting one side at a time can cause the stand to warp and create 
problems in the assembly.
Downloaded From ManualsPrinter.com Manuals 
						

							14 Chapter 1 Read this first
Assembling the Stand
4.Remove the tape that is attached the left and right sides of Stand Upper Stay (d).[37] 
5.Arrange the Stand Upper Stay so that the bends in the brackets on the left and right 
side (e) are facing up, and the side marked with an R is facing the Stand Leg R (a). 
Insert the Stand Upper Stay into the groove between Stand Leg R (a) and Stand Leg 
L (c).
[38] 
6.Securely fasten the hex screws on the left and right side using the supplied M8 hex 
driver to fix the Stand Stay in place.
[39] 
Downloaded From ManualsPrinter.com Manuals 
						

							15
Assembling the Stand
7.Place the Stand in the installation location and lock the front casters.[40] 
Downloaded From ManualsPrinter.com Manuals 
						

							16 Chapter 1 Read this first
Installing the Printer
Installing the Printer
Illustration
[41] 
[42] 
1.Remove the box from the printer body and clear out the packing material from above 
the printer, then lift up the base of the printer one side at a time and clear out the 
packing material from under the printer.
[43] 
2.Fold and then peel off the double-sided tape (c) from the Stand Extensions Boards, 
then stick Stand Extension Board (e) to the side of Stand Leg R (d) and Stand 
Extension Board (g) to the side of Stand Leg L (f).
[44] 
Downloaded From ManualsPrinter.com Manuals 
						

							17
Installing the Printer
3.Have 4 people grasp the handholds in the base of the printer body, then align the side 
of the printer body (h) with the line on the Stand Extension Board (i) and put the 
printer on the stand.
[45] 
4.Remove Stand Extension Board (e) and (g) from the Stand Legs.
5.Securely affix the printer body to the stand using 2 hex screws on each side starting 
from the bottom of the stand backing plate.
[46] 
Downloaded From ManualsPrinter.com Manuals 
						

							18 Chapter 1 Read this first
Attaching the Output Stacker
Attaching the Output Stacker
1.Insert the Rod Holders (c) into holes on the back of Stand Leg L (a) and Stand Leg 
R (b).
[47] 
2.Insert Output Stacker Arm L (e) and Output Stacker Arm R (f) into the grooves (d) 
in the left and right ends of the Stand Upper Stay, then attach them using 2 hex 
screws.
[48] 
3.Stretch out the Output Stacker fabric such that the white mark (g) on the fabric is at 
the front right, and the center Output Stacker Rod (h) is at the back.
[49] 
Downloaded From ManualsPrinter.com Manuals 
						

							19
Attaching the Output Stacker
4.Attach the Output Stacker Rod (j) in the center of the Output Stacker fabric to the 
Rod Holder (i), and loop the hole in the fabric (k) over the hook (l) above the Rod 
Holder.
[50] 
Attention: Attach the Output Stacker Rods to the Rod Holders in front of the 
Output Stacker Arm and at the very back of the Rod Holder. If the Output Stacker 
Rods are attached to the second rod holder from the back, the media will not 
enter the Output Stacker when ejected, and may cause dirtying or damage to the 
print surface. Use the rod holder that is second from the back to temporarily hold 
the Output Stacker Rod during maintenance.
5.Pull out to the back any slack in the paper stacker cloth, and then attach the two 
Output Stacker Rods to the Rod Holders at the very back and front of the Output 
Stacker Arm.
[51] 
Downloaded From ManualsPrinter.com Manuals 
						

							20 Chapter 1 Read this first
Removing the Packing Material
Removing the Packing Material
1.Removing the tape and packing material that is attached to the printer body.[52] 
2.Open the top cover.[53] 
3.Lift up Release Lever (a) and remove the protective sheet (b) from the Platen, then 
lower the Release Lever.
[54] 
a
b
Downloaded From ManualsPrinter.com Manuals