Oce ColorWave 600 User Manual

Set the 'Océ Finishing Assistant'
Introduction
This setting is only available when the 'Configuration' - 'Printer setup' - 'Finishing' -
'Finisher configuration
 type' setting is set to 'Estefold'.
The

 'Océ Finishing Assistant' can automatically detect the legend (if present) of a drawing
and rotate and align the drawing so the legend will be on the cover page of the fold
package. If

 no legend can be detected the print is delivered unfolded....

Chapter 2 - Get to know the printing system42Set the 'Océ Finishing Assistant'
Downloaded From ManualsPrinter.com Manuals 

Chapter 3
Prepare 
the printing sys-
tem 
for use and get start-
ed
Downloaded From ManualsPrinter.com Manuals 

Introduction
This chapter contains all the information you need to prepare your Océ ColorWave 600
for use.
You can  learn more about the following.
• How to

 move the printer.
• How to

 
connect the power supply cable and the network cable.
• How
 to run 
the installation procedure.
• How
 to (re)load 
the toner cartridges.
• How to
 (re)place the maintenance tray.
• How to

 (re)load 
a media roll.
• How to
 complete the printer configuration in the Océ Express WebTools.
• How to

 
configure the...

How to move the Océ ColorWave 600
IntroductionAttention:
If connected you must first switch off and disconnect the Océ ColorWave 600. (see
‘Switch on or switch off the printer’  
on page 172)
Attention:
Close the media drawers. Chapter 3
 - Prepare the printing system for use and get started 45How to move the Océ ColorWave 600
Downloaded From ManualsPrinter.com Manuals 

Note:
Be aware of the printer working area. (see ‘Printer working area [Footprint]’ on page 23) #
Illustration
Action Use 
both hands to pull at the
'Lower left cover'. Remove the
'Lower left

 cover'.
1 Pull 
at the Foot cover. Remove
the 'Foot'
 cover.
2 Push 
the handle [1]. The 'Foot'
snaps up [2].
3
Repeat

 action 1
 till 3 on the
'Lower right
 cover' 4
Chapter 3
 - Prepare the printing system for use and get started46How to move the Océ ColorWave 600...

Illustration
Action Move the Océ ColorWave 600
printer.
Note:
Be aware of the printer
working area. 5
Pull 
out the left 'Foot' [1] until
it
 touches the ground and locks
[2]. 

You should hear a click as it
locks.
Note:
If you do not hear a
click, 
place your foot on
the foot of the printer
[1] 

and at the same time
push 
gently against the
printer until
 you 
hear
the click. 6
Pin:Replace 
the 'Foot' covers. Place
the
 pin into 
the notch. 7a
Chapter 3
 - Prepare the printing system...

Illustration
Action
Notch:7b
7c
Pin:Replace the 'Lower left cover'.
Place 
the pin into the notch. 8a
Chapter 3
 - Prepare the printing system for use and get started48How to move the Océ ColorWave 600
Downloaded From ManualsPrinter.com Manuals 

Illustration
Action
Notch:8b
8c
Repeat action 6 till 8 at the right
hand side. Replace the 'Lower
right cover' 9
Chapter 3
 - Prepare the printing system for use and get started 49How to move the Océ ColorWave 600
Downloaded From ManualsPrinter.com Manuals 

Connect the Océ ColorWave 600 printer
How to connect the network cable #
Illustration
Action Remove the cover of the 'Con-
nection 

panel' at the rear side of
the printer.
1 Lead the connection cable
through

 the cover.
2 Connect one side of the data ca-
ble 
(UTP cable with a RJ45
connector) 
to the indicated net-
work connection on the connec-
tion panel of the 'Océ PowerM controller'.
Connect

 the other side of the
network 
cable to your company
network. 3
Chapter 3
 - Prepare the...