Nortel Modular Ics 6.0 Programming Record Manual

							103
P0992642 03Modular ICS 6.0 Programming Record
 Cd2 on KSUSelect the type of card that occupies the second slot in the ICS.
Note: The slots are numbered from left to right. 
Version note: If your system is using 4x8 software which has not been 
upgraded, this setting does not appear.
 Mod 03
 Mod 04
 Mod 05
 Mod 06
 Mod 07
 Mod 08View and program the cards installed in the modules.
Note: MICS-XC also has modules 9-14.
 StnModIndicate that the module is a Station Module
 ASMIndicate that the module is an Analog Station Module
 Tr u n k M o dIndicate that the module is a Trunk Module
 DataModIndicate that the module is a datamodule:
 Norstar Integrated Data Module 200 (IDM 200)
 BayStack
 Synchronous Data Interface (SDI)
 Ty peIndicate the type of data module. 
You can change the type if no data module is currently attached to the 
expansion port.
 IP addressIndicate the IP address for a data module (BayStack only).
 Fixed accessAssign Fixed lines to supported data modules
 IDM 200
 BayStack
 SDI).
 Switched accessAssign lines used for dial-up network access to the data module (BayStack 
only).
 Line assignmentSelect fixed lines the data module (BayStack only) uses for switched access.
 Line pool accessIndicate line pool switched access for the data module (BayStack only).
 DataMod NVRAMUse to reset the NVRAM of the IDM 200 data module to the factory defaults.
 ConfigUse to configure the settings for the SDI.
 PtlSelect the physical interface  used to connect the SDI to the networking 
equipment.
 DS0 rateSelect the transmission rate of the channels (Fixed lines) assigned to the SDI.
 TxClk srcSelect whether data travelling through the SDI is synchronized using timing 
(clocking) from the SDI or the DTE.
 TxClk invrsnInvert the signal used by the SDI to synchronize data from the DTE to adjust 
for round trip delays between the SDI and DTE.
 Data invrsnInvert data travelling through the SDI before routing it to the T1 connection or 
DTE to allow the SDI to support HDLC/SDLC (a transmission standard for 
data) protocol.
 Lp stateShow the direction of the loopback, if any, generated by the SDI. 
						

							104
Modular ICS 6.0 Programming RecordP0992642 03
 Fixed accessAssign fixed lines to supported data modules:
 IDM 200
 BayStack
 SDI).
 Maintenance These commands allow you to make diagnostic checks on the system.
 System versionRecord the system version shown on the display.
 Port/DN statusView the Port/DN status.
 Module status View the Module status.
 Sys test logView items in Sys test log.
 Sys admin logView items in log.
 Network evt logView the items in the Network Log.
This log keeps a record of events and alarms involving the digital network 
interface.
 ProvisioningPlace BRI loops in or out of service.
 TestsRun and list any BERT-set tests.
 CSU statsView the performance statistics for your T1 lines.
 Diagnostic toolsDiagnostic tools programming performed by experienced personnel.
 Link Status
 Usage metrics 
 Hunt GroupsUse to gather statistical information about Hunt group usage.
 Call-by-CallUse to gather statistical information about PRI CbC calls. 
						

							Meridian, Norstar, and Companion are trademarks of Nortel Networks Corporation.
Meridian, Norstar and the Business Communications System are manufactured by Nortel Networks Corporation.
This document is for use with Norstar Modular ICS and Norstar Modular ICS-XC 6.0 systems.
© 2002 Nortel Networks Corporation
All rights reserved
P0992642 03
Printed in Canada