Nortel Modular Ics 6.0 Programming Record Manual

							93
P0992642 03Modular ICS 6.0 Programming Record
 COS pswd #00Indicates the number of  the password  to  which you are assigning  information.
 Pswd 00Enter a six-digit password.
 User fltAssign a restriction filter to the Class of Service password.
 Line fltSelect whether a Class of Service password will use the default line filter or a 
different line filter (enter the two-digit filter number).
 Remote pkgSelect whether a Class of Service password will use the default remote 
package or a different remote package (enter the two-digit remote package 
number).
 Call log pswdsA programming section that allows you to clear any Call Log password 
programmed with the Call Log feature.
 Show set:_Enter the D N of the telephone you want to program.
 Log pswdErase the call log password for this telephone.
 Programing pswdsIn this section you can create your own password rather than use the default.
 InstallerEnter the new installer password which gives you access all the programming 
settings.
 SysCoord+Enter the new system coordinator password which gives you access to 
selected programming settings.
 Sys coordEnter the new system coordinator password which gives you access to 
everyday programming settings.
 BasicEnter the new basic password which gives you access to the most  commonly 
used programming settings.
 Reg pswd.
(MICS-XC only)Enter the new registration password that allows you to register Companion 
portable sets to the system.
 HospitalityUse these commands to create Hospitality services passwords if required, 
rather than use the defaults.
 Desk pswdEnter the new Desk password which gives access to all Hospitality services 
programming settings.
 Cond pswdEnter a Condition password which gives certain employees access to the 
Room condition programming settings in Hospitality services.
Time&DateUse these commands to set the system clock to the correct time and date.
System prgrmingUse these commands to change system-wide settings.
 Hunt groupsThese commands allow you to set up incoming calls on a specific DN to be 
routed to a group of sets.
 Show group:_Enter the D N of the telephone you want to program.
 Member DNsEnter the D N of the telephone you want to add to the group.
 Line assignmentAssign or unassign a line to a particular hunt group.
 Mode:Determine how an incoming call will be handled by the hunt group.
 Hunt delay: Select a delay value to determine how long a set rings before the call moves 
on the next member set.
 If busy:Determine how an incoming call is to be treated when all hunt group member 
sets are busy. 
						

							94
Modular ICS 6.0 Programming RecordP0992642 03
 Q Timeout: Set the number of seconds the incoming call remains in the hunt group call 
queue before it is offered to the overflow position.
 Overflow: Enter the DN of the set you want the hunt group overflow calls to be 
presented.
 Name:Enter the name of the hunt group.
 Aux ringerIndicate if an external ringer will be used.
 Distinct RingUse this setting to determine the Distinctive Ring Pattern you want to use to 
identify the Hunt group. This setting works in conjunction with Line and 
Telephone distinctive ring settings.
 Change DNsChange the DN of a telephone. 
All DNs must be the same length. 
The first digit of a new DN cannot be the same as the:
 external line access code
 Call Park prefix
 Direct-dial digit
 first digit of a line pool access code
If you change an individual DN, you must quit programming for the change to 
take effect.
 Featr settingsUse these commands to set or change features for specific sets.
 Backgrnd musicSelect whether users can listen to music through their telephone speaker 
using the Background Music feature (
²°fl). 
A customer-supplied music source must be connected to the ICS.
 On hold Select whether a caller on hold hears:
 music from an outside source, such as a radio connected to the ICS
 periodic tones
 silence
 Receiver volumeSelect whether the volume of a telephone receiver/headset automatically 
resets to the system default level, or retains the level set at the telephone.
 Camp timeoutSelect the number of seconds a call can remain camped before it returns to 
the telephone that camped it. 
 Par k timeou tSelect the number of seconds a call on an external line can remain parked 
before it returns to the telephone that parked it.
 Par k mo deSelect whether the system will use Call Park codes in a sequence from lowest 
to highest, or use the lowest numbered code that is available when the call is 
parked.
 Tr n s f r  c a l l b kSelect the number of times a transferred call rings before it returns to the 
telephone that transferred it.
 DRT to primeSelect whether to automatically transfer unanswered external calls to a prime 
telephone. 
 DRT delaySelect the number of times a call rings before Delayed Ring Transfer 
transfers it to a prime telephone. This setting only appears if DRT to prime is 
Yes.
 Held reminderSelect whether the telephone reminds you when a call is on hold.
 Remind delaySelect the number of seconds before the telephone reminds you that a call is 
on hold. The setting only appears if Held reminder is Yes.
 Directd pickupSelect whether users can answer calls at any  telephone using the directed 
call pickup feature (
²àß). 
						

							95
P0992642 03Modular ICS 6.0 Programming Record
 Page toneSelect whether users can hear a Page Announcement tone (²ßâ) over 
the system. 
 Page Timeout Select the number of seconds before a Page is automatically disconnected.
 Daylight timeSelect whether daylight savings time is automatically applied to the system 
clock.
 AutoTime&DateSelect whethe r time and day will automatically display.
 SWCA CntrlThis feature provides 16 feature codes which allow you to park calls on the 
system. If these codes are assigned to memory buttons with indicators in a 
group of telephones, then incoming calls can be assigned to the buttons and 
maintain a call appearance for the group, while freeing up the line for 
additional calls.
 Auto AssociateUse this command to determine if calls are automatically assigned to a free 
SWCA key.
 Invoke by HoldUse this command to determine if calls are automatically assigned to a free 
SWCA key if they are put on Hold.
 Call log spaceCustomize how Call log space is allocated to telephones in the system.
 Reset all logs?Use this command to confirm that you want to reallocate the Call log space 
equally to all telephones in your system.
 Host delay Select the delay, in milliseconds, between the selection of an outgoing line 
and the moment that Norstar sends dialed digits or codes on that line.
 Link time
 AlarmSetEnter the DN of the telephone used to display alarm messages when a 
problem occurs in the Norstar system. 
 Set relocationSelect whether telephones in the system can be moved without losing their 
programming.
 Msg reply enhSelect  whether to provide light message waiting lamps or a stuttered dialtone 
on selected analog telephones on specially equipped ASMs. 
 Ans. key:Allows you to assign up to eight answer keys. Settings are Basic, Enhanced, 
and Extended. 
 CLID MatchUse this command to determine how many digits an incoming calls must 
match to a System Speed Dial listing to allow the speed dial name to display 
for the call.
 Direct-dialSelect whether an internal or external number is used for the Direct-dial 
telephone.
 D-Dial 1Enter the internal or external numbers that the system will automatically dial 
when someone enters the Direct-dial digit.
 Intrnl# Enter the DN number of the direct-dial telephone. If it  is an external number, 
you will also have to choose how the outgoing call is made.
 D-Dial 2 
 D-Dial 3
 D-Dial 4
 D-Dial 5Program the settings for each direct-dial telephone, as you did for Set 1. 
						

							96
Modular ICS 6.0 Programming RecordP0992642 03
 CAP assignmentUse these commands to assign the DNs of telephones to a the central 
answering position (CAP) module attached to a M7234 telephone.
 CAP 1
 CAP 2 
 CAP 3 
 CAP 4 
 CAP 5 Enter the DN of the CAP telephones.
 Dialing plan
 Private networkIf you are networking your system using dedicated PRI lines, you need to set 
up the same dialing plan on all nodes of the system.
 Ty p e(None, CDP, UDP)
This fields defines the type of dialing plan.
 PrivNetID(CDP and UDP only) This is the unique network identifier for each node.
 Loc code(UDP only) This is the code that provides access to a UDP-based node.
 Priv DN lenThis is the number of digits the nodes require to recognize where the 
information needs to be routed.
 Public networkIf you are networking through PSTN public lines, you can specify which 
numbers will be recognized as belonging to the system.
 Pub DN lengthsThis is the DN length the system will recognize
 Show prefixThese are the prefixes the system will recognize.
 Prfx: Deflt
 DN length
 Dial timeoutThis is the timer for releasing a call that cannot be routed over the network.
 Dial timeout
 Access CodesUse these commands to enter the access codes for:
 Line pool
 Park prefix
 Extrnl code
 Direct-Dial
 Auto DN
 DISA DN
 Line pool codesEnter a line pool access code for each line pool (1-4 digits). 
A line pool access code cannot start with the same digits as the:
 Call Park prefix
 Direct-dial digit
 any DN (including Recd #s, the DISA DN, or the Auto DN)
 destination code
 Park prefixSelect the first digit of the Call Park retrieval code. 
						

							97
P0992642 03Modular ICS 6.0 Programming Record
 Extrnl codeEnter the one-digit external line access code. 
This code allows an M7100 telephone or a device connected to an ATA to 
access external lines. 
The external line access code cannot be the same as the:
 Call Park prefix
 Direct-dial digit
 first digit used by an internal DN
 Direct-dialSelect the digit used  to dial a Direct-dial telephone. 
The digit cannot be the same as the:
 first digit of a DN
 line pool access code
 external line access code
 Call Park prefix
 first digit of a destination code
 Auto DNEnter the DN that a remote user can dial on an auto answer Loop line so that 
the line is answered with system dial tone. 
A remote user can then use the system resources allowed by the remote 
access package assigned to the line. The length of the Auto DN is the same 
as the Recd # length.
The Auto DN cannot be the same as a:
 line pool access code
 destination code
 DISA DN Enter the DN a remote user can dial on an auto answer Loop line so that the 
line is answered with stuttered dial tone. A remote user must then enter a 
Class of Service password to gain access to system resources. 
The remote access package assigned to the Class of Service password 
determines which resources they can use. 
The length of the DISA DN is the same as the Recd # length. 
The DISA DN cannot be the same as a:
 line pool access code
 destination code
 PrivAccCodeEnter the special code for your private network access.
 Carrier CodesEnter the signal for a carrier code entry.
 Remote accessUse these commands to create a system of controlled access to your Norstar 
system.
 Remote access pkgsCreate packages to apply to lines that allow or restrict the remote access to 
Norstar line pools and/or to paging. 
 Show pkg:_Enter the two-digit remote package number  (00-15). Package 00 is pre-set to 
allow no access.
 LinePool accessFor each package, select whether the user will have access to the system line 
pools.
 Pool For each line pool, select whether a remote user can have access.
 Remote page For each package, select whether a remote user can access the Page 
feature.
 Rem line accessSelect the remote access packages to be applied.
 Show line:_ Enter the line number. 
						

							98
Modular ICS 6.0 Programming RecordP0992642 03
 Change DN type
(MICS-XC systems, only)These commands allow you to change DN types for the range of DNs that are 
available to either portable telephones or ISDN terminal equipment.
 Show DN:_Enter the DN for which you want to change the DN type.
 637Select whether this DN is reserved for use with a portable telephone or with 
ISDN terminal equipment.
 StateUse this softkey item to see whether a portable has been assigned to the DN.
Companion
(MICS-XC systems, only)These commands allow you to set up base stations and program the 
portables in your Companion system.
 RegistrationUse these commands to register the portables to the system.
 RegistrationTurn portable registration on or off.
 Portable DNsIdentify the access line to which a portable is registered.
 Show DN:_Display the DN of the portable.
 Radio dataThese commands allow you to initiate a re-evaluation of the radio status.
 Re-evaluationThis command automatically assigns base stations to cells and defines the 
cell configuration.
 StatusIdentify the status of the Re-evaluation.
 Schedule
 RadiosThese commands provide information about cell assignment and antenna 
type.
 Cell assignmentView whether a radio is assigned to a cell or unassigned.
 Show radioEnter the number of the radio.
 Antenna typeIndicate the type of antenna selected for each base station.
 Show radioEnter the number of the radio.
 CellsThese commands provide information about the cells within the system.
 Show cell:_Enter the number of the cell you wish to program.
 Cell radios Assign a radio to this cell.
 Show radio:_Enter the number of the radio.
 Cell nghbrs Assign a cell to be a neighbor. This is a cell that physically adjoins another 
cell.
 Show nghbrView neighbor information.
 Cell rad nghbrs Assign a cell to be a bordering cell to each cell neighbour.
 Show RadNghbrView cell radio neighbor information.
 System LID
(MICS-XC systems, only)Use these commands to determine the System Access Logical Identifier (LID) 
by which the system identifies itself to portable telephones, and by which the 
portable telephones request service from the system.
 Rec’d # lengthSelect the number of digits received on auto-answer lines. 
These digits are used to identify the Auto DN and DISA DNs, and to route 
calls to target lines. 
						

							99
P0992642 03Modular ICS 6.0 Programming Record
 DN length:_Select the length of DNs. 
DN length can be three to seven digits. Each increase in DN length adds the 
digit 2 to an existing DN (for example: DN 344, when increased to five digits, 
becomes 22344).
 Nat’nl lengthThe length of the telephone number  dialed to reach a person within the same 
country.
 Make/Break:Select the Make/Break ratio. The default Make/Break ratio is 40 / 60. 
 BusNameEnter the name of the business. This name displays on the receiving set, 
where the line allows.
 CbC limitsThese commands allow you to program the minimum and maximum incoming 
and outgoing calls for a PRI line pool.
 Pool PRI-ASelect the PRI line pool (PRI-A, PRI-B....) for which you want to set the limits.
 Show: PublicSelect Public or Private, or Tie, FX, OUTWATS, 800
 Min incomingEnter the minimum number of incoming PRI lines you need.
 Max incomingEnter the maximum number of incoming PRI lines you need.
 Min outgoingEnter the minimum number of outgoing PRI lines you need.
 Max outgoingEnter the maximum number of outgoing PRI lines you need.
 Release reasonsRelease reasons.
 HospitalityThese commands allow you to create the hospitality settings.
 Room/desk informationThese commands allow you to assign sets to a room.
 Show set:_Indicate the set you wish to configure.
 Room #:_Indicate the room associated with the set.
 Adm pwd req’d:Indicate whether the set requires the use of the Hospitality Desk Admin 
password to access Hospitality Desk features.
 Call RestrnsThese commands allow you to assign dialing filters to room occupancy 
states.
 VacantThis command notes if the Room is empty or occupied.
 Use flt:Enter the dialing filter for the room state. The filters range from 00 to 99.
 BasicIndicate the filter to be assigned for that level of room occupancy.
 MidIndicate the filter to be assigned for that level of room occupancy.
 FullIndicate the filter to be assigned for that level of room occupancy.
 Service timeThese commands allow you to program a system-wide time when occupied 
rooms change state from Service done to Needs service.
 HourEnter the hour.
 MinutesEnter the minutes. 
						

							100
Modular ICS 6.0 Programming RecordP0992642 03
 AlarmThese commands allow you to configure the Alarm operation.
 Attn attemptsEnter the number of times the Alarm time feature attempts to get the attention 
of the occupant before cancelling.
 Retry intrvlEnter the interval period between each Alarm attempt.
This setting is in minute intervals.
 Attn durationSet the period for which a set alerts on each alarm attempt.
This setting is in seconds.
 Time formatChoose if alarm times are entered using a 12 hour or 24 hour clock.
 Expired AlarmsThese commands allow you to determine how the system will notify you about 
expired alarms.
 Notify setUse this command to choose whether the set where the alarm was 
programmed will be notified if the alarm expires.
 Use ToneUse this command to choose what tone will be used if the set is notified that 
an alarm has expired.
 Network servicesThese commands are used for MCDN connections only.
 ETSI (profile 2 only)These features can be supplied by your service provider over ETSI lines.
 Netwrk Redirection (NCD)Use this command to indicate whether you want to be able to call forward 
calls over the network.
 MCIDUse this command to indicate whether the MCID feature code can be used to 
record call information at the CO.
 MCDN (profiles 1, 2, and 4)Press Next to move to next entry.
 NetwkICCLSelect whether you want ISDN Call Control Limitation to be set for your 
MCDN network.
 TROSelect whether you want Trunk Route Optimization to be active on the MCDN 
networks.
 TATSelect whether you want Trunk Anti-Tromboning to be set for your MCDN 
network.
Telco featuresThese commands allow you to assign settings for external voice messaging 
services.
 VMsg ctr tel#sThese commands allow you to determine which voice message center the set 
will use, and how it will access the network.
 VMsg center 1
 VMsg center 2
 VMsg center 3
 VMsg center 4
 VMsg center 5Choose the voice message center you want the set to use.
 Use: line| routing tblSelect whether the set will access the voice message center over a direct line, 
or through a routing table.
 Te l #Enter up to a 24-number telephone number that accesses the voice 
messaging center. 
						

							101
P0992642 03Modular ICS 6.0 Programming Record
 ONN blockingAllows outgoing name and number to be blocked at the called party end on 
both analog and digital lines.
 Analog VSCAnalog Vertical service code.
 To n eVertical service code for analog tone dialing trunks.
 PulseVertical service code for analog pulse dialing trunks.
 BRI VSCBasic Rate Interface Vertical service code.
 Code:Enter the BRI code.
Software keys These commands allow you to set up access to optional features and 
services through Nortel Networks programming.
 SysIDThis number can be viewed on any M7324, M7310, or T7316  display. Record 
the number. You will be asked to provide this number when you call the Nortel 
Customer Response Center.
 Password keysKeys are required for some system expansion activities and to activate the 
remote monitoring capability. To obtain the required keys for ISDN PRI, and 
fixed access trunks/WAN access for Data Modules, call the Nortel Customer 
Response Center at: 1-800-684-5825.
Note: An ISDN PRI key is required for MCDN networking.
 Key 1Enter the eight-digit password.
 Key 2Enter the eight-digit password.
 Key 3Enter the eight-digit password.
HardwareUse these commands to view and configure the Trunk Cartridges and BRI 
Cards installed in the ICS.
 Show module:_Indicate the module you wish to view.
 Cards on KSUView and program the cartridges and cards installed in the ICS.
 Cd1-KSUView the type of card that occupies the right-most slot in the ICS.
 Card typeThe display shows the current card type.
 LinesView the line-number range for the lines on a Trunk Cartridge.
 Show lines ___
 Protocol
 PrivNetId
 Discon timerSpecify the duration of an Open Switch Interval for a Trunk Cartridge.
 Answer timerSelect the minimum duration, in seconds, of an answer signal before a call is 
considered to be answered, for an E&M trunk cartridge.
 CO failSelect the carrier failure standard used by your T1 service provider. 
This setting only appears for DTIs.
 I/F levelsInterface levels defaults to the ISDN loss plan setting. 
Check with your telecommunications service provider to find out the I/F level 
of your connection:
 digital network loss treatment (ISDN I/F levels) 
 analog network loss treatment (PSTN I/F levels) 
 FramingUse to select the framing format used by your T1 service provider. 
This setting only appears for DTIs. 
						

							102
Modular ICS 6.0 Programming RecordP0992642 03
 Internal CSUUse to turn the internal TI channel service on or off.
The channel service unit gathers performance statistics for your T1 lines.
 CSU line bldUse to set the gain level of the transmitted signal. 
This setting only appears for DTIs that have their internal CSU turned on.
 DSX1 bldUse to set the distance between the ICS and an external channel service unit. 
This setting only appears for DTIs that have their internal CSU set to Off.
 Line codingSelect the standard used by your T1 service provider for encoding signals on 
the T1 lines.
 ClockSrcDetermine the type of clock  source.
 LoopsView the loops on a BRI Card.
 Loop nnnView the settings for a particular loop on a BRI Card.
 Ty peView or change the loop type.
 SamplingSelect the sampling used by an S-loop.
 DNs on LoopAssign the ISDN DNs that use this loop.
 Assign DNsEnter ISDN DNs for each S-loop or LT loop.
 Show DN:_Indicate whether or not the DN is assigned to a loop.
 Loop DN:_Select the main ISDN DN, if any, for   the loop.
 SPID1Enter the SPID supplied by your service provider.
 # of B-channlsSelect the number of B-channels that are associated with the SPID.
 Network DNsEnter the Network DNs that are associated with the SPID. 
A Network ISDN DN can be assigned to more than one SPID.
 Call typeSelect the Call type used with the Network DN. 
For each ISDN DN, use only one of each of the Voice and Data call type 
settings, or a single Both call type setting. 
 D-packet servceConfigure the D-packet service for this loop. 
Only one loop on each card can support D-channel packet service.
 D-packet servceTurn the D-packet service for this loop on or off.
 Lp001Select the loop that supports the D-packet service:
 S-loop (for BRI-ST Card) 
 LT-loop (for BRI-U2 or BRI-U4 Card)
 TEIsAdd up to eight Terminal Endpoint Identifiers (TEIs). 
Each TEI is supplied by your service provider. A TEI is associated with an 
ISDN device.
 TEIEnter the two-digit TEIs supplied by your service provider.
 ClockSrcDetermine the type of clock  source.
 ONN blkDetermine if ONN blocking will be allowed for BRI loops.
 SPID2Enter the second SPID supplied by your service provider, if applicable.