Nitsuko Nvm-2 Installation Instructions

NVM-2e Installation Instructions
Issue 1-07
Voice Mail Specifications
Number of Ports: 2 or 4
Voice Storage Capacity: 3 hours
Subscriber Mailboxes: Up to 50 Subscriber Mailboxes
Trunk Mailboxes Up to 8, depending on phone 
system
Telephone System A Phone System Single Line
Programming Interface: Extension
Electrical Requirements: 120V, 60 Hz
Environmental Requirements: 50-104 deg F, 10-40 deg C
Site Requirements
„ 
Do not expose this product to rain or any type of moisture.
„ 
Do not locate the unit near...

NVM-2e Installation Instructions
8Issue 1-0
Install NVM-2e
Use the following instructions to install your NVM-2e.
To Install the NVM-2e:
1. Place the Voice Mail on any sturdy flat surface.
 OR
 Mount the Voice Mail on a wall, using the screw slots located on
the bottom of the cabinet.  Make sure that the ventilation slots are
not blocked.  Position the cabinet so that the LEDs can be seen.
 
2. Plug the Voice Mail power supply cord into the connector labeled
“24 VAC.”  Plug the adapter box into a 120V,...

NVM-2e Installation Instructions
Issue 1-09
Connect a Laptop to the NVM-2e
A laptop is required for certain programming and is also used as a tool
for diagnostics.
You will need
 to connect a laptop computer to NVM-2e so that you
can access a program called “The System Configuration Management
Program.”  This program allows you to configure certain parameters in
the Voice Mail which you cannot access through a System
Administrator’s Mailbox.
The System Configuration Management Program is described in...

NVM-2e Installation Instructions
10Issue 1-0
Connect a Laptop to the NVM-2e (cont’d)
Figure 5:  Required Pin-outs for the RS-232 Cable
 
 
4. When the laptop is communicating with the Voice Mail, you will
see a menu screen and the prompt, 
Main Menu - > .
 
 Proceed to 
Connect a Phone System to NVM-2e on page 11. 

NVM-2e Installation Instructions
Issue 1-011
Connect a Phone System to NVM-2e
You can connect a Portrait, 28i, 124i, Onyx VS or Businesscom DS01
phone system to the NVM-2e.  For specific equipment that you need
for each phone system, see the NVM-2 Setup Guide (P/N 17690SET02
or higher).
To connect a Portrait phone system to the NVM-2e:
1. Plug one end of a modular line cord into Port 1 on NVM-2e.  Plug
the other end into an RF14 to RJ11 adapter or RJ14 jack.  See
Figure 6.
 
2. Using a 4-wire modular...

NVM-2e Installation Instructions
12Issue 1-0
Connect a Phone System to NVM-2e (cont’d)
Note:
  An alternate method for installing the 28i/124i is on the
following page.
To connect NVM-2e to a 28i, 124i, Onyx VS or Businesscom DS01
phone system:
1. Plug one end of a modular line cord into Port 1 on the NVM-2e.
Plug the other end into an ASI or Dual ASI.
 
2. Connect the ASI or Dual ASI to the phone system.  Figure 7 shows
connecting to a Dual ASI.
 
3. Repeat steps 1 and 2 for Port 2.
 
4. Repeat steps 1...

NVM-2e Installation Instructions
Issue 1-013
Connect a Phone System to NVM-2e (cont’d)
Note:
  The following is an alternate method for connecting the 28i or
124i to the Voice Mail.
To connect NVM-2e to a 28i or 124i Phone System:
1. Plug one end of a modular line cord into Port 1 on NVM-2e.  Plug
the other end into an RJ11 modular jack.  See Figure 8.
 
2. Repeat step 1 for Port 2.
 
3. Repeat step 1 for Ports 3 and 4 if your Voice Mail has four ports.
 
 Note:  Extensions will receive notification of...

NVM-2e Installation Instructions
14Issue 1-0
Program NVM-2e for the Correct Phone System
The default phone system that the Voice Mail recognizes as installed is
the Portrait.  If you connected a 28i, 124i, Onyx VS or Businesscom
DS01 to NVM-2e, you will need to change the default setup in
programming so that the Voice Mail recognizes your phone system.
To change the phone system that NVM-2e recognizes as installed:
1. Log onto the System Administrator Mailbox (extension 10 in the
Portrait).  From any...

NVM-2e Installation Instructions
Issue 1-015
Start Up the System Configuration Management Program:
The System Configuration Management Program allows you to
configure certain parameters in the Voice Mail which you cannot
access through a System Administrator’s Mailbox.
The System Configuration Management Program is described in detail
in the NVM-2 Release Notes for Version 1.05.07 (P/N 17690UPG01 or
higher).
 To use The System Configuration Management Program, you need to
connect a laptop computer to the...