Nitsuko 124i/384i Software Manual

Table 1-5, Function Key Codes by Number
To program a key, press CALL, dial 851, press the key and enter the code (e.g., 1057 for Voice Over).
Use this key... For this feature... When you are... Key Lamp StatusAlso see
Srvc Code
Code: 1050
Operation: Press keyAutomatic Call
Distribution (ACD)Out of Service
Taking an ACD Group out of
Service (for Group
Supervisors only), or Taking
all ACD Groups out of service
(for System Supervisors only)--
Code: 1051
Operation: Press keyTerminal Speech Monitor
Monitoring...

Table 1-5, Function Key Codes by Number
To program a key, press CALL, dial 851, press the key and enter the code (e.g., 1057 for Voice Over).
Use this key... For this feature... When you are... Key Lamp StatusAlso see
Srvc Code
Code: 1060
Operation: Set up call
+ Press keyVoice Mail (cont.) Using Voice Mail Record Slow Flash red
when active- 
Code: 1073
Operation: Press key
+ 2 (
Change), 3
(
Delete) or 6 (
New)Caller ID Changing, deleting or adding
new numbers None 146
Code: 1074
Operation: Press...

Table 1-6, System Number Plan/Capacities
System Type:384i 124i
System
Tenant Groups 4 1
Classes of Service 15 per Tenant 10
Toll Restriction Classes 15 per Tenant 8
Caller ID Bins 1000 200
Trunks
Trunk Port Numbers
11-128 1-52
Trunk Group Numbers 1-128 1-16
Trunk Access Maps 1-128 1-52
Trunk Routes 1-64 1-36
Ring Groups 1-128 1-16
Caller ID Bins 1000 (0-999) 200 (0-199)
DID Translation Tables 8 4
DID Translation Table Entries 1500 200
Tie Line Classes of Service 16 11
Tie Line Toll Restriction Classes 15...

Table 1-6, System Number Plan/Capacities
System Type:384i 124i
Abbreviated Dialing
Abbreviated Dialing Groups 32 8
Abbreviated Dialing Bins 1990 360
Department and Pickup Groups
Department (Extension) Group Numbers 1-32 1-8
Department (Extension) Group Number
Range200-799 200-799
Group Call Pickup Group Numbers 1-9 or 01-32 1-8
DCIs
DCI Software Port Numbers
 DCI Modules
  DCI Module Ports (1 port per unit)
 3-DCI Units
  3-DCI Unit Ports (3 ports per unit)1-288
144
1-144
48
145-2881-72 (Same as ext.)...

Table 1-6, System Number Plan/Capacities
System Type:384i 124i
Passwords
User Password for Setting Time and
Date, Music on Hold tone, Night Serv-
ice and Toll Restriction Override0000 0000
Passwords (Cont’d)
Programming Passwords
    Level 2 (IN - Tenant 0)
    Level 3 (SA - Tenant 1)
    Level 4 (SB - Tenant 1)12345678
0000
999912345678
0000
9999
Footnotes
1  Count toward total number of allowed hardware ports (124 or 384 – depending
  on the system).
2  These devices share the same pool of extension...

Table 1-7  System Tones
Tone Repetitions Frequency Level Pattern
Internal, Special and External
Dial ToneContinuous 350 Hz + 440
Hz-16 dB Steady
Internal Recall Dial Tone 3 350 Hz + 440
Hz-16 dB 100 mS Off, 100 mS On
Internal Busy Tone 1 Continuous 480 Hz + 620
Hz-27 dB 500 mS Off - 500 mS On
DND Busy Tone Continuous  400 Hz -13 dB 200 mS Off, 200 mS On
Internal Reorder Tone  Continuous 480 Hz + 620
Hz-27 dB 250 mS Off, 250 mS On
Internal Intercept Tone Continuous  350 Hz + 440
Hz-16 250 mS Off, 250 mS...

Table 1-7  System Tones
Tone Repetitions Frequency Level Pattern
Sensor Alarm Tone 1 Continuous  800 Hz  -13 dB 200 mS On, 200 mS Off 
Sensor Alarm Tone 2 Continuous 800 Hz  -13 dB 500 mS On, 500 mS Off
Sensor Alarm Tone 3 Continuous  800 Hz  -13 dB 700 mS On, 700 mS Off 
Internal Call Waiting Tone 1  440 Hz  -16 dB 200 mS On
Internal Executive Override
To n e1  440 Hz  -16 dB 3 Seconds On 
Conference Tone, Intrusion
Tone 2, Internal Special
Audible ToneContinuous Variable: 440 Hz + 480 Hz at -22 dB for...

Table 1-7  System Tones
Tone Repetitions Frequency Level Pattern
Extension Ring Tone Range Combination of... 
High: 800 Hz + 1032 Hz + 12 Hz 
Med: 604 Hz + 865 Hz + 12 Hz
Low: 400 Hz + 640 Hz + 12 HzSelected in Program 1001 Item 3
for extensions
Sensor Ring Tone Range (1-3) Combination of... 
High: 800 Hz + 1000 Hz
Med: 800 Hz + 1000 Hz
Low: 800 Hz + 1000 HzSet in Program 0304 for alarm
sensors. (Pitch is identical, but
pattern is unique for ranges 1-3.) 
Introducing the Features
Charts and...

Table 1-8  Multibutton Telephone Displays
With this feature... You’ll see this display...  When...
(Idle telephone)
Date and Time
Ext (ext name)Your extension is idle and on hook
CHECKYou press CHECK to check a function
CHECK (ext) (ext name)
PORT nn   GP-nnYou press CHECK and CALL1 to check extension
information, where (ext) is the extension number,
(ext name) is the extension name, PORT nn is the
port number and GP-nn is the extension group 
Abbreviated Dialing
SET ABB:COMMONYou dial Service Code 853...

Table 1-8  Multibutton Telephone Displays
With this feature... You’ll see this display...  When...
Alarm
SET ALARM 
1:ALARM1  2:ALARM2You dial 827 to set an alarm
SET     n  ALARM 
DIAL  TIMEYou dial 827 to set an alarm, then dial 1 (to set
Alarm 1) or 2 (to set Alarm 2)
Date and Time 
Ext ALARM nYour extension is idle, after setting Alarm n (1 or 2)
SET     n  ALARM
TimeYou set an alarm time but do not hang up
SET     n  ALARM
CANCELYou dial 827, 1 or 2 to select an alarm type then
9999 to cancel 
ALARM...