NEC Visualink 128/384 User Guide

NDA-24230 Issue 2.0Page 4-23
VisuaLink 128/384 User Guide Chapter 4
4.3 Software Setup
When you first turn on your VisuaLink, there will be an initial configuration 
screen.  These configuration screens will have to be completed before your system 
becomes operational.
Start up configuration screens
The following are the startup screens that will be active on first power up or acti-
vated on demand by the user after choosing the Environmental initialize. 
Welcome Screen:  
This is a welcome screen for...

Page 4-24NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Remote Controller Directions: 
Gives some general directions for configure the VisuaLink system.  Using the 
Remote controller highlight the NEXT option to advance to the configure screen 
or press the lower portion of the CAMERA CONTROL key to highlight the 
Configure Later to advance to the normal ICON screens.  If you choose to 
configure later, the system will have to be programmed with My numbers and 
SPID’s in order to work...

NDA-24230 Issue 2.0Page 4-25
VisuaLink 128/384 User Guide Chapter 4
Video Number 1 Screen’s
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 1).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s .  All four numbers must be entered.  Choose 
NEXT when complete.  
Note:
“PROCEED TO STEP 2” will only be shown on the VisuaLink 128 system.  
VisuaLink 384 will show “ Proceed to Line 2 Setup”   
Step 1--Enter My Number and SPID...

Page 4-26NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Video Number 2 Screens:
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 2).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s .  All four numbers must be entered.  Choose 
NEXT when complete.
Note:
  This screen will only appear on the VL 384 system.
Step 1--Enter My Number and SPID for BRI LINE 2
    My Number 1:
 []
    SPID 1:
    [ ]
    My Number...

NDA-24230 Issue 2.0Page 4-27
VisuaLink 128/384 User Guide Chapter 4
Video Number 3 Screens:
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 3).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s .  All four numbers must be entered .  Choose 
NEXT when complete.
Note: 
 This screen will only appear on the VL 384 system.
4.5 Optional User 
Settings:The following is a description for Optional Setting screen.
Step 1--Enter My...

Page 4-28NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Optional information:
You may enter this optional information.  The name you enter makes it easy for 
users to identify this particular VisuaLink.  The name can be up to 20 characters 
long.  The Password is the password needed to be entered when selecting the 
Utilities ICON.  After entering the optional information select the NEXT to 
advance to the next screen.  
Application Screen’s
Using the number pad on the wireless remote...

NDA-24230 Issue 2.0Page 4-29
VisuaLink 128/384 User Guide Chapter 4
Congratulations Screen
The VisuaLink is now setup for the configuration you have entered.  Press the 
ENTER
 button on the REMOTE CONTROLLER
, the VisuaLink will display a 
blue screen and recycle.  The VisuaLink should will power up to a normal state.   
You may begin to use the video conferencing system immediately.
Note:
If there are no My Numbers entered in the configuration the VisuaLink 
will display the Start Up screens.
Step...

Page 4-30NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Powering Up Screen
Changing the configuration
It is important that the CODEC is set up with a local number and SPID numbers.  
If the unit is not setup with a local number (my number) and SPID, the unit will 
not allow for dialing and receiving of video calls.  If you have entered these 
numbers in the Start Up configuration, you may ignore this section.  If the 
VisuaLink environment has changed, such as the phone number have changed,...

NDA-24230 Issue 2.0Page 5-1
VisuaLink 128/384 User Guide Chapter 5
Chapter 5  System Parameter/Environment Setting
System parameter sets the operation conditions of the VisuaLink 128 or 
VisuaLink 384.  Environment setting can be set such as camera class, audio 
related, data related, line related and local office status.  Loopback feature can be 
used as a maintenance feature.
Note 1:
Make system parameter changes when the system is not connected.
Note 2:
Depending on the setting for audio, data speed...

Page 5-2NDA-24230 Issue 2.0
Chapter 5 VisuaLink 128/384 User Guide
Á
Move the cursor with the CAMERA CONTROL 
button to the 
ENVIRONMENT SETTING
 icon.
Â
Press the ENTER
 button.
The system will not operate correctly if the environment setting are incorrect.  
Therefore, the system has a password so that only the person in charge of 
controlling video conference can change the settings.  Factory default password is 
1234
.
s
Setting environments.
CAMERA
CONTROL
Please input password....