NEC Visualink 128/384 Director Guide

NDA-24248 Revision 1.0Page 5-5
VisuaLink 128/384 Director Guide Chapter 5
5.3 Camera Control 
ToolboxThe Camera Control Toolbox appears with floating toolbox. The Camera Control 
Toolbox provides the following icons and control buttons.
Figure 5-3:   Camera Control
A. Local Camera 1
Activates local control for CAMERA 1
 (Main Camera).
B. Local Camera 2
Activates local control for CAMERA 2
 (Sub Camera.)
C. Remote Camera 1
Activates remote control for CAMERA 1
 (Main Camera).
D. Remote Camera 2...

Page 5-6NDA-24248 Revision 1.0
Chapter 5 VisuaLink 128/384 Director Guide
Note 1:
 Camera Control Toolbox is available during the conference. You can use 
the Camera Control Toolbox when camera is selected on Maintenance/
Environment/Serial Port 1
.
Note 2:
 In order to manipulate [Remote Camera 1] and [Remote Camera 2] 
during the Multi-point conference, the chairman mode must be activated.  
Remote camera control will only work if the remote system (MCU 
included) support H.281/H.224 or NEC camera...

NDA-24248 Revision 1.0Page 6-1
VisuaLink 128/384 Director Guide Chapter 6
Chapter 6   Status bar
The Status bar appears on the lower edge of the VisuaLink Director main window. 
The Status bar displays information shown below.
Figure 6-1:   Status Bar
A. Functional Description
Displays a brief description of the menu or toolbar/toolbox icon. This display 
appears when a pointer is placed over the menu or toolbar/toolbox.
B. MCU Sending Status
Displays SENDING
 when local terminal is sending image to...

Page 6-2NDA-24248 Revision 1.0
Chapter 6 VisuaLink 128/384 Director Guide
D. Communication status
Displays the communication status of local terminal. 
Connecting
:  Negotiating with the remote terminal.
Calling
:  Calling remote terminal.
Receiving
:  Receiving a call.
Communicating
:  Conference is established.
Disconnecting
:  Requesting to disconnect.
No Display
: No connection. 

NDA-24248 Revision 1.0Page 7-1
VisuaLink 128/384 Director Guide Chapter 7
Chapter 7   Connect/Disconnect Line
This chapter describes the fundamentals of connecting the line (calling/receiving) 
and disconnecting the line when you wish to terminate the conference.
If you use the basic proprietary line that provides line establishment at any time, 
you may skip ahead to the operations described in this chapter.
7.1 Connect Line 
(Calling) Direct-
dial settingFollow the operation below to connect the line...

Page 7-2NDA-24248 Revision 1.0
Chapter 7 VisuaLink 128/384 Director Guide
B. Dial 1 Sub Address/Dial 2 Sub Address
Enter remote Dial 1 sub address /Dial 2 sub address into each entry field. You can 
use dial keys or keyboard to enter address up to 8 digit. Dial 2 sub address entry is 
not available unless select [2B] on the communication speed.
C. Dial Key
[0
] ~ 
[9
]: Use these keys for Dial 1, Dial 1 sub address, Dial 2, and Dial 2 sub 
address entry.
[*
]  
[#]
: Not available
[DEL
] : Use this key...

NDA-24248 Revision 1.0Page 7-3
VisuaLink 128/384 Director Guide Chapter 7
7.2 Connect Line 
(Calling) Redial 
SettingYou can connect the line by selecting a participant from previous call/receive 
history (redial). Follow the operation below to initiate the redial.
Operation
Select Connection
 | Connect   | Redial 
from the Main Menu
. 
Redial
 dialog appears.
Figure 7-2:   Redial Screen
A. Redial List
Redial List (call/receive history) can retain up to 10 redial numbers.
Redial List displays calls in...

Page 7-4NDA-24248 Revision 1.0
Chapter 7 VisuaLink 128/384 Director Guide
C. Delete All List 
button 
When you click this button, a dialog appears to confirm the deletion of all the 
Redial Numbers. Accept to delete all the contents of the Redial list, cancel to 
return back.
D. Close
 button
Closes Redial
 dialog box.
Note 1:
Selecting the receive information from Redial List will disable the Dial 
2 and Dial 2 Sub Address information, otherwise only the Dial 1 and 
Dial 1 Sub Address information are...

NDA-24248 Revision 1.0Page 7-5
VisuaLink 128/384 Director Guide Chapter 7
7.3 Connect Line 
(Calling) 
Phonebook SettingYou can connect the line by select a participant from the Phonebook. Follow the 
operation below to use the Phonebook.
Operation
Click Connect (Phonebook)
 icon on the Standard Toolbar
. Or select 
Connection
 | Connect 
 | Phonebook
 from the Main Menu
.
Figure 7-3:   Connection Screen
s 

Page 7-6NDA-24248 Revision 1.0
Chapter 7 VisuaLink 128/384 Director Guide
Phonebook
 dialog appears.
Figure 7-4:   Phonebook Screen
A. Phone List
Phone List can retain up to 130 call profiles. Displays the call profiles in the order 
of registrations. 
B. Headers
Call profile headers are buttons. Click any field name button to sort the items 
based on the selection.
C. Search
Search through the Phonebook to find a match. Search history shows a log of the 
last 16 previous items in a drop down menu.
D....