NEC Projector UM352W User Manual

29
❹ Changing Eco Mode/Checking Energy-Saving Effect 
Using Eco Mode [ECO MODE]
The	ECO	MODE	(NORMAL	and	ECO)	increases	lamp	life,	while	low ering	pow er	consumption	and	cutting	down	on	
CO2	emissions.	
Four	brightness	modes	of	the	lamp	can	be	selected:	[OFF],	[AUTO	ECO],	[NORMAL]	and	[ECO]	modes .	
[ECO	MODE]	DescriptionStatus	of	LAMP	indicator
[OFF]The	lamp	brightness	is	100%.Off
[AUTO	ECO]Lamp	power	consumption	will	be	changed	between	
[OFF]	and	[NORMAL]	automatically	according	to	
picture	level
NOTE:...

30
Checking Energy-Saving Effect [CARBON METER]
This	feature	will	show	energy-saving	effect	in	terms	of	CO2	emission	reduction	(kg)	when	the	projector’s	[ECO	MODE]	
is	set	to	[AUTO	ECO],	[NORMAL],	or	[ECO].	This	feature	is	called	as	[CARBON	METER].
There	are	two	messages:	[TOTAL	CARBON	SAVINGS]	and	[CARBON	SAVINGS-SESSION].	The	[TO TAL	CARBON	
SAVINGS]	message	shows	the	total	amount	of	CO2	emission	reduction	from	the	time	of	shipment	up	to	now.	You	can	
check	the	information	on	[USAGE	TIME]	from	[INFO.]...

31
❺ Using 4-Point Corner to Correct Keystone Distortion 
[CORNERSTONE]
Use	the	[KEYSTONE	HORIZONTAL],	[KEYSTONE	VERTICAL]	(able	to	correct	simultaneously),	[CORNERSTONE]	
and	[PINCUSHION]	to	correct	keystone	distortion.
Cornerstone
1.	 When	APPS	is	not	selected	as	source	and	the	menu	is	not	displayed	on,	press	the	KEYSTONE	button	on	
the remote.
 The KEYSTONE screen will be displayed.
•	 Press	the	KEYSTONE	button	when	using	the	remote	control.
•	 See	page	for	PINCUSHION.
2. Press the ▼	button	to	select...

32
7. Use the ▲▼◀▶ button to move the projected image frame as shown on the example.
8. Press the ENTER button.
9. Use the ▲▼◀▶ button to select another icon which points in the direction.
	 On	the	Cornerstone	adjustment	screen,	select	[EXIT]	or	press	the	EXIT	button	on	the	remote	control.
 The confirmation screen is displayed.
10. Press the ◀ or ▶	button	to	highlight	the	[OK]	and	press	the	ENTER	button.
This	completes	the	Cornerstone	correction.
Selecting	[CANCEL]	will	return	to	the	adjustment	screen...

33
Pincushion
1.	 Press	the	KEYSTONE	button	with	no	menu	displayed.
 The KEYSTONE screen will be displayed.
•	 Press	the	KEYSTONE	button	when	using	the	remote	control.
2. Press the ▼	button	to	select	[PINCUSHION]	and	then	press	
the ENTER.
3. Press either ▲ or ▼ button to select one from top, bottom, left, 
right, and then press either  ◀ or ▶  button to reform pincushion 
distortion.
NOTE:
•	 Once	a	side	is	reformed,	it	disables	reforming	remaining	three	sides.
•	 For	changing	the	side	to	be	reformed,...

34
Reset	the	keystone	and	pincushion	adjustment	to	the	initial	value
1.	 Press	the	KEYSTONE	button	with	no	menu	displayed.
 ON the displayed KEYSTONE menu, set the cursor at RESET using the ▼ button and press ENTER button.
•	 Confirmation	message	is	displayed	on.
2. Move the cursor onto YES using either ◀ or ▶ button and then press the ENTER.
NOTE:
•	 All	adjusted	values	set	in	the	KEYSTONE	adjustment	are	reset	to	initial	values
TIP:
Adjustable	range	of	the	KEYSTONE	and	the	CORNERSTONE:
Horizontal...

35
❻ Preventing the Unauthorized Use of the Projector [SECURITY]
A	keyword	can	be	set	for	your	projector	using	the	Menu	to	avoid	operation	by	an	unauthoriz ed	user.	When	a	ke yword	
is	set,	turning	on	the	projector	will	display	the	Keyword	input	screen.	Unless	the	correct	ke yword	is	entered,	the	pro-
jector	cannot	project	an	image.	
•	 The	[SECURITY]	setting	cannot	be	cancelled	by	using	the	[RESET]	of	the	menu.
To	enable	the	Security	function:
1. Press the MENU button.
 The menu will be displayed.
2....

36
7. Type in the same combination of ▲▼◀▶ buttons and press the ENTER button.
 The confirmation screen will be displayed.
8.	 Select	[YES]	and	press	the	ENTER	button.
	 The	SECURITY	function	has	been	enabled.
To	turn	on	the	projector	when	[SECURITY]	is	enabled:
1. Press the POWER button.
	 The	projector	will	be	turned	on	and	display	a	message	to	the	effect	that	the	projector	is	locked.
2. Press the MENU button.
3. Type in the correct keyword and press the ENTER button. The projector will display an...

37
To	disable	the	SECURITY	function:
1. Press the MENU button.
 The menu will be displayed.
2.		Select	[SETUP]	→	[INSTALLATION]	→	[SECURITY]	and	press	the	ENTER	button.
 The OFF/ON menu will be displa yed.
3.	 Select	[OFF]	and	press	the	ENTER	button.
	 The	SECURITY	KEYWORD	screen	will	be	displayed.
4. Type in your keyword and press the ENTER button.
	 When	the	correct	keyword	is	entered,	the	SECURITY	function	will	be	disabled.
NOTE:	If	you	forget	your	keyword,	contact	your	dealer.	Your	dealer	will...

38
❼ Connecting Your Microphone
 
Connecting	a	commercially	available	dynamic	microphone	or	condenser	mic	to	the	MIC	input	jack	allows	you	to	output	
your	mic	sound	from	the	built-in	speaker.
Sound	input	from	all	input	terminals	including	APPS	and	USB-B	will	be	heard	from	the	speaker	with	your	microphone	
voice.	
Select	the	microphone	type	(dynamic	microphone	or	condenser	microphone)	from	the	menu	[SETUP]	→	[INSTAL-
LATION]	→	[MIC	SELECT].
Microphone	sensitivity	can	be	adjusted.	From	the	menu,	select...