NEC Projector UM352W User Manual

9
❹ Part Names of the Remote Control
´
3
4
6
71
210
16
17
15
149
5
8
13
30
31
32
20
21
26
28
29 25
24
23 22
27
33
19
18
12
11
1. Infrared Transmitter
	(
→	page	10)
2.	 POWER	ON	Button
	(→	page	14)
3.	 POWER	STANDBY	Button
	(→	page	24)
4.	 SOURCE	Button
	(→	page	16)
5.	 COMPUTER	1	Button
	(→	page	16)
6.	 COMPUTER	2	Button
	 (This	button	does	not	wor k	in	this	
series	of	projectors)
7.	 AUTO	ADJ.	Button
	(→	page	23)
8.	 HDMI	1/MHL	Button
	(→	page	16)
9.	 HDMI	2	Button
	(→	page	16)
10.	DisplayPort	Button...

10
Remote Control Precautions
•	 Handle	the	remote	control	carefully.
•	 If	the	remote	control	gets	wet,	wipe	it	dry	immediately.
•	 Avoid	excessive	heat	and	humidity.
•	 Do	not	short,	heat,	or	take	apart	batteries.
•	 Do	not	throw	batteries	into	fire.
•	 If	you	will	not	be	using	the	remote	control	for	a	long	time,	remove	the	batteries.
•	 Ensure	that	you	have	the	batteries’	polarity	(+/−)	aligned	correctly .
•	 Do	not	use	new	and	old	batteries	together,	or	use	different	types	of	batteries	together.
•...

11
❺ Part names of the supplied stylus pen
Indicator	(LED)Charging port (USB)
Pen tip
Charging the stylus pen
1. Use the supplied USB cable f or charging the stylus pen to connect the charging port (USB) of the stylus 
pen with the USB port of the computer.
2. Automatically start charging the stylus pen. It takes about 3 minutes to complete.
•	 Pressing	the	pen	tip	against	a	screen	or	white	board	will	turn	the	indicator	LED	to	red,	which	indicates	that	
charging is completed and you are ready to use the...

12
This	section	describes	how	to	turn	on	the	projector	and	to	project	a	picture	onto	the	screen.
❶ Flow of Projecting an Image
Step 1
•	 Connecting	your	computer	/	Connecting	the	power	cord	(→ page 13)
 
Step 2 
•	 Turning	on	the	projector	(→ page 14)
 
Step 3 
•	 Selecting	a	source	(→ page 16)
 
Step 4
•	 Adjusting	the	picture	size	and	position	(→ page 17)
•	 Correcting	keystone	distortion	[KEYSTONE]	(→ page 21)
 
Step 5
•	 Adjusting	a	picture	and	sound
- Optimizing a computer signal automatically (→...

13
❷ Connecting Your Computer/Connecting the Power Cord
1.	 Connect	your	computer	to	the	projector.
 This section will show you a basic connection to a computer. For information about other connections, see “5. 
Installation	and	Connections”	on	page	77.
	 Connect	the	computer	cable	(VGA)	between	the	projector’s	COMPUTER	IN	terminal	and	the	computer’s	port	(mini	
D-Sub 15 Pin). Turn two thumb screws of both terminals to fix the computer cable (VGA).
2.	 Connect	the	supplied	power	cord	to	the	projector....

14
❸ Turning on the Projector
•	 Press	the		(POWER) button on the projector cabinet 
or the POWER ON button on the remote control. 
	 The	POWER	indicator	will	blink	and	the	projector	will	be-
come ready to use.
TIP:	
•	 When	the	message	“Projector	is	locked!	Enter	your	password.”	
is	displayed,	it	means	that	the	[SECURITY]	feature	is	turned	on.	
(→	page	35)
 After you turn on your projector, ensure that the computer 
or video source is turned on.
NOTE:	When	no	input	signal	is	present,	the	no-signal...

15
Note on Startup screen (Menu Language Select screen)
When	you	first	turn	on	the	projector,	you	will	get	the	Startup	menu.	This	menu	gives	you	the	opportunity	to	select	one	
of	the	30	menu	languages.
To	select	a	menu	language,	follow	these	steps:
1. Use the ▲, ▼, ◀ or ▶ button to select one of the 30 
languages from the menu.
2. Press the ENTER button to e xecute the selection.
After	this	has	been	done,	you	can	proceed	to	the	menu	
operation.
If	you	want,	you	can	select	the	menu	language	later.
(→...

16
❹ Selecting a Source
Selecting the computer or video source
NOTE:	Turn	on	the	computer	or	video	source	equipment	connected	to	the	projector.
Detecting	the	Signal	Automatically
Press	the	SOURCE	button	once.	The	projector	will	search	for	the	avail-
able	input	source	and	display	it.	The	input	source	will	change	as	follows:	
COMPUTER	→	HDMI1/MHL	→	HDMI2	→	VIDEO	→	USB-B	→	APPS
•	 With	the	SOURCE	screen	displayed,	you	can	press	the	SOURCE	
button	a	few	times	to	select	the	input	source.
TIP:	If	no	input...

17
❺ Adjusting the Picture Size and Position
Use	the	adjustable	tilt	foot,	the	zoom	function	or	the	focus	ring	to	adjust	the	picture	size	and	position.
In	this	chapter	drawings	and	cables	are	omitted	for	clarity.
Adjusting	horizontal/vertical	position
(→	page	18)
Adjusting	the	focus	[Focus	ring]
(→	page	18)
Finely	adjusting	the	left	and	right	tilt	[Tilt	Foot]
(→	page	19)
Adjusting	the	size	[Digital	Zoom]
(→	page	20)
Correcting	the	keystone	distortion	[Keystone]*
(→	page	21)
*	 To	perform	keystone...

18
Adjusting horizontal/vertical position
The	throw	distance	can	affect	the	size	and	the	height	of	the	projected	image.	Before	installing	the	projector,	decide	
the	throw	distance	according	to	“Setting	Up	the	Screen	and	the	Projector”	(→	page	75)
It	is	recommended	to	display	the	test	pattern	while	adjusting	the	image.	(→	page	64)	
1. Move the projector back and forth and left and right so that 
the image fits the screen width.
	 You	can	reduce	the	image	size	to	70%	by	using	[DIGITAL	ZOOM]	
from the...