NEC Projector UM352W User Manual

79
Connecting an External Monitor
You	can	connect	a	separate,	exter nal	monitor	to	your	projector	to	simultaneously	view	on	a	monitor	the	computer	
analog	image	you’re	projecting.
NOTE:
•	 The	AUDIO	OUT	mini	jack	does	not	support	Headphone	terminal.
•	 When	audio	equipment	is	connected,	the	projector	speaker	is	disabled.
•	 The	signal	output	from	the	MONITOR	OUT	(COMPUTER)	of	this	projector	is	for	projecting	image	on	exclusive	one	display.
•	 When	no	signal	is	applied	over	3	minutes	in	the	condition	of...

80
Connecting Your DVD Player or Other AV Equipment
Connecting	Video	Input
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
VIDEO	IN	VIDEO(VIDEO)
NOTE:	Refer	to	your	VCR	owner’s	manual	for	more	information	about	your	equipment’s	video	output	requirements.
NOTE:	An	image	may	not	be	displayed	correctly	when	a	Video	source	is	played	back	in	fast-forward	or	fast-rewind	via	a	scan...

81
Connecting Component Input
	 A	component	signal	will	be	automatically	displayed.	If	not,	from	the	menu,	select	[SETUP]	→	[OPTIONS(1)]	→ 
[SIGNAL	SELECT]	→	[COMPUTER],	and	then	place	a	check	mark	in	the	Component	radio	button.
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN	COMPUTER(COMPUTER	1)
NOTE:	Refer	to	your	DVD	player’s	owner’s	manual	for	more	information...

82
Connecting HDMI Input
You	can	connect	the	HDMI	output	of	your	DVD	player,	hard	disk	play er,	Blu-ra y	play er,	or	notebook	type	PC	to	the	
HDMI	IN	terminal	of	your	projector.
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
HDMI	1/MHL	IN	HDMI1/MHL(HDMI1/MHL*)
HDMI	2	IN	HDMI2(HDMI2*)
•	 When	connecting	the	HDMI1/MHL	IN	terminal	(or	HDMI2	terminal)	of	the	projector	to	the	DVD...

83
Connecting a smart phone and a tablet terminal
The	below	mentioned	feature	is	available	when	the	projector	is	connected	with	MHL	supported	devices	such	as	a	
smart	phone	and	a	tablet	terminal	by	a	MHL	cable	(not	supplied)
•	 Projecting	a	image	and	a	file	on	the	MHL	supported	devices.
•	 Output	sound	on	the	MHL	supported	devices	from	the	build-in	speaker.
•	 Charge	the	MHL	supported	devices.
•	 Operate	the	MHL	supported	devices	by	the	remote	control	for	the	projector.
•	 Operate	the	projector	by	the...

84
Connecting your document camera
You	can	connect	your	document	camera	and	project	printed	documents,	etc.
Name, position, and direction of terminals are 
vary	depending	on	camera	model.	Please	chec k	user's manual of y

our camera for details.
Computer cable (VGA)
(supplied)
Video cable (not supplied)
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN...

85
Connecting to a Wired LAN
The	projector	comes	standard	with	a	LAN	port	(RJ-45)	which	provides	a	LAN	connection	using	a	LAN	cable.	
To	use	a	LAN	connection,	you	are	required	to	set	the	wired	LAN	settings	on	the	projector	menu.	Select	[SETUP]	→ 
[INSTALLATION]	→	[NETWORK	SETTINGS].	(→	page	64).
Example	of	LAN	connection
Example	of	wired	LAN	connection
Server
Hub
LAN cable (not supplied)
NOTE:	Use	a	Category	5	or	higher	
LAN	cable.
5. Installation and Connections  

86
Connecting to a Wireless LAN (Optional: NP05LM series)
The	USB	Wireless	LAN	Unit	also	provides	a	wireless	LAN	connection.	To	use	a	wireless	LAN	connection,	you	are	
required	to	assign	an	IP	address	to	the	projector.
Important:	
•	 If	you	use	the	projector	with	the	USB	Wireless	LAN	Unit	in	the	area	where	the	use	of	wireless	LAN	equipment	is	prohibited,	remove	
the	USB	Wireless	LAN	Unit	from	the	projector.
•	 Buy	the	appropriate	USB	Wireless	LAN	Unit	for	your	country	or	area.
NOTE:	
•	 The	green	LED	on...

87
Example	of	wireless	LAN	connection
To	use	a	LAN	connection,	you	are	required	to	set	the	Wireless	LAN	settings	on	the	projector	menu.	Select	[SETUP]	
→	[INSTALLATION]	→	[NETWORK	SETTINGS].	(→	page	64).
 
PC with wireless LAN card inserted PC with built-in wireless 
LAN function
Wired LAN
Wireless access point
USB Wireless LAN Unit
5. Installation and Connections  

88
6. APPS MENU
❶ What can you do with the APPS MENU?
It	becomes	available	to	select	the	expansion	functions	indicated	in	below	and	various	setting	with	the	APPS	MENU.
For	displaying	the	APPS	MENU,	press	the	APPS	button	on	the	remote	or	select	[APPS]	as	the	[SOURCE]	on	the	
onscreen	menu.
Once	calibration	for	the	stylus	pen	is	performed,	the	stylus	pen	becomes	av ailable	for	selecting	and	setting	up	var ious	
functions	on	the	APPS	MENU.
INFORMATION
Detailed	information	about	each	function	on	the	APPS...