NEC Projector PH1202HL User Manual

26
❼ Turning off the Projector
To turn off the projector:
1. First, press the  (POWER) button on the projector 
cabinet or the POWER OFF button on the remote con-
trol. 
	 The	[POWER	OFF	/	ARE	YOU	SURE	?	/	CARBON	SAV-
INGS-	SESSION	0.000[g-CO2]]	message	will	appear.
 
2. Secondly , press the ENTER button or press the  
(POWER) or the POWER OFF button again.
	 When	the	projector	is	in	STANDBY	MODE,	the	POWER	
indicator	lights	up	red.	(When	[STANDBY	MODE]	is	in	
[NORMAL]	setting)
•	 Before	the	POWER...

27
NOTE:
•	 Do	not	unplug	the	power	cord	from	the	projector	or	from	the	power	outlet	while	an	image	is	being	projected.	Doing	so	could	
deteriorate	the	projector’s	AC	IN	terminal	or	the	power	plug’s	contact.	To	turn	off	the	AC	power	supply	when	the	projector	is	
powered on, use the projector’s main power switch, a power strip equipped with a switch, or a breaker.
•	 Do	not	turn	off	the	main	power	switch	or	disconnect	the	AC	power	supply	within	10	seconds	of	making	adjustments	or	setting	
changes	and...

28
3. Convenient Features
❶ Stopping projection
1. Press the SHUTTER button on the projector or on the remote 
control.
	 The	light	source	will	turn	off	and	the	light	of	the	projector	will	temporar ily	
go	dark.	The	SHUTTER	indicator	will	turn	on	in	g reen.
	 Press	the	button	again	and	projection	will	resume.	The	SHUTTER	
indicator	will	turn	off.
	 You	can	set	the	projection	light	to	gradually	fade	in	or	fade	out.
On	the	projectorOn	the	remote
SHUTTER indicator
❷ Turning off the light source
1 Press the...

29
❹ Muting the Image (AV Mute)
Press	the	AV-MUTE	button	to	turn	off	the	image	for	a	short	period	of	time.	
Press	again	to	restore	the	image.
TIP:
•	 The	image	will	disappear	but	not	the	menu	display.
❺ Turning Off the On-Screen Menu (On-Screen Mute)
A	press	of	the	ON-SCREEN	button	on	the	remote	control	will	hide	the	
on-screen	menu,	the	source	display	and	other	messages.	Press	again	
to	restore	them.	
TIP:
•	 To	confirm	that	the	on-screen	mute	is	turned	on,	press	the	MENU	button.	If	the	on-screen	menu...

30
❼ Magnifying a Picture
You	can	magnify	the	picture	up	to	four	times.
NOTE: 
•	 Depending	on	an	input	signal,	the	maximum	magnification	may	be	less	than	four	times,	or	the	function	may	be	restricted.
To	do	so:
1.	 Press	the	D-ZOOM	(+)	button	to	magnify	the	picture.
2. Press the ▲▼◀▶ button.
	 The	area	of	the	magnified	image	will	be	moved
3. Press the D-ZOOM (−) button.
	 Each	time	the	D-ZOOM	(−)	button	is	pressed,	the	image	is	demagni-
fied.
NOTE: 
•	 The	image	will	be	magnified	or	demagnified	at	the...

31
❽ Changing LIGHT MODE/Checking Energy-Saving Effect 
Using LIGHT MODE [LIGHT MODE]
When	either	[ECO1]	or	[ECO2]	in	[LIGHT	MODE]	is	selected,	motion	noise	of	the	projector	is	cut	down	by	lowering	
brightness	of	its	light	source.	By	saving	energy	consumption,	the	CO2	emission	from	this	projector	can	be	reduced.
LIGHT	MODEIcon	at	the	bottom	
of	the	menuDescription
NORMAL
100%	brightness
The	screen	will	be	brightly	lit.
ECO1Brightness	will	be	at	about	80%.
The	cooling	fan	will	also	slow	down	accordingly....

32
NOTE: 
•	 The	[LIGHT	MODE]	can	be	changed	by	using	the	menu.
	 Select	[SETUP]	→	[INSTALLATION]	→	[LIGHT	MODE]	→	[LIGHT	MODE].
•	 The	light	module	used	hours	can	be	checked	in	[USAGE	TIME].	Select	[INFO.]	→	[USAGE	TIME].
•	 After	a	lapse	of	1	minute	from	when	the	projector	displays	a	blue,	black	or	logo	screen,	[LIGHT	MODE]	will	automatically	switch	
to	[ECO].	By	the	automatic	setting	to	[ECO],	the	projector	will	be	automatically	reset	to	the	previous	setting	when	it	detects	input	
signal.
•	 If	the...

33
Checking Energy-Saving Effect [CARBON METER]
This	feature	will	show	energy-saving	effect	in	terms	of	CO2	emission	reduction	(kg)	when	the	projector’s	[LIGHT	MODE]	
is	set	to	either	[ECO1],	[ECO2],	or	[LONG	LIFE].	This	feature	is	called	as	[CARBON	METER].
There	are	two	messages:	[TOTAL	CARBON	SAVINGS]	and	[CARBON	SAVINGS-SESSION].	The	[TO TAL	CARBON	
SAVINGS]	message	shows	the	total	amount	of	CO2	emission	reduction	from	the	time	of	shipment	up	to	now.	You	can	
check	the	information	on	[USAGE	TIME]	from...

34
❾ Correcting Horizontal and Vertical Keystone Distortion 
[CORNERSTONE]
Use	the	[CORNERSTONE]	feature	to	correct	keystone	(trapez oidal)	distortion	to	make	the	top	or	bottom	and	the	left	
or	right	side	of	the	screen	longer	or	shorter	so	that	the	projected	image	is	rectangular.
1.	 Press	and	hold	the	3D	REFORM	button	for	2	seconds	at	least	to	reset	current	adjustments.
	 Current	adjustments	for	[GEOMETRIC	CORRECTION]	will	be	cleared.
2.	 Project	an	image	so	that	the	screen	is	smaller	than	the	area	of...

35
5. Press the ▼	button	to	align	with	the	[CORNERSTONE]	and	then	press	the	ENTER	button.
The	drawing	shows	the	upper	left	icon	(	)	is	selected.
	 The	screen	will	switch	to	the	[CORNERSTONE]	screen.
NOTE:
•	 When	a	[GEOMETRIC	CORRECTION]	function	other	than	[CORNERSTONE]	has	been	set	up,	the	[CORNERSTONE]	screen	
will	not	be	displayed.	When	the	screen	is	not	displayed,	either	press	the	3D	REFORM	button	for	2	or	more	seconds,	or	run	
[RESET]	in[GEOMETRIC	CORRECTION]	to	clear	the	adjustment	value	of...