NEC Projector PH1202HL User Manual

16
2. Press the  (POWER) button on the projector cabinet 
or the POWER ON button on the remote control. 
	 The	POWER	indicator	goes	from	a	steady	red	light	to	
a	flashing	blue	light,	and	the	picture	is	projected	on	the	
screen.
•	 If	using	the	remote	co ntrol,	pr ess	th e	PO WER	ON	but ton.
•	 When	there	is	no	signal	the	unit	will	project	a	blue	screen	
(factory	default	menu	settings).
•	 If	the	picture	is	blurry,	adjust	the	screen	focus .	(→	page	
24)
•	 When	it	is	dark	press	the		(lights)	button.	The...

17
Note on Startup screen (Menu Language Select screen)
When	you	first	turn	on	the	projector,	you	will	get	the	Startup	menu.	This	menu	gives	you	the	opportunity	to	select	one	
of	the	29	menu	languages.
To	select	a	menu	language,	follow	these	steps:
1. Use the ▲, ▼, ◀ or ▶	button	to	select	one	of	the	29	
languages	from	the	menu.
 
2. Press the ENTER button to e xecute the selection.
After	this	has	been	done,	you	can	proceed	to	the	menu	
operation.
If	you	want,	you	can	select	the	menu	language	later.
(→...

18
❹ Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or video source equipment connected to the projector.
Detecting	the	Signal	Automatically
Press	the	SOURCE	button	for	1	second	or	longer.	The	projector	will	
search	for	the	available	input	source	and	display	it.	The	input	source	will	
change	as	follows:	
HDMI	→	DisplayPort	→	BNC	→	BNC(CV)	→	BNC(Y/C)	→	COMUPTER	
→	HDBaseT	→	SLOT	→ …
•	 Press	it	briefly	to	display	the	[INPUT]	screen.	
	 Press	the	▼/▲	buttons	to	match...

19
Selecting Default Source 
You	can	set	a	source	as	the	default	source	so	that	it	will	be	displayed	each	time	the	projector	is	turned	on.
1. Press the MENU button.
	 The	menu	will	be	displayed.
2. Press the ▶	button	to	select	[SETUP]	and	press	the	▼	button	or	the	ENTER	button	to	select	[BASIC].
3. Press the ▶	button	to	select	[SOURCE	OPTIONS].
4. Press the ▼	button	four	times	to	select	[DEFAULT	INPUT	SELECT]	and	press	the	ENTER	button.
	 The	[DEFAULT	INPUT	SELECT]	screen	will	be	displayed.
	(→	page...

20
❺ Adjusting the Picture Size and Position
Use	the	lens	shift	dial,	the	level	adjuster	lev er,	the	zoom	lev er/zoom	ring	and	the	focus	ring	to	adjust	the	picture	size	
and	position.
In	this	chapter	drawings	and	cables	are	omitted	for	clarity.
Adjusting	the	projector’s	settings
[Level	adjuster]
(→	page	21)
Adjusting	the	projected	image’s	vertical	and	horiz ontal	
position
[Lens	shift]
(→	page	22)
Adjusting	the	focus
[Focus]
(→
	page	24)
Finely	adjusting	the	size	of	an	image
[Zoom]
(→
	page	24)
TIP:
•...

21
CAUTION
•	 Perform	the	adjustment	from	behind	or	from	the	side	of	the	projector.	Adjusting	from	
the	front	could	expose	your	eyes	to	strong	light	which	could	injure	them.	
•	 Keep	hands	away	from	the	lens	mounting	portion	while	the	lens	shift	is	in	operation.	
Failure	to	do	so	could	result	in	hands	being	pinched	by	the	moving	lens.
Adjustment of the projector’s settings (Level adjusters)
The	projector	must	be	placed	square	to	the	screen	otherwise	ke ystone	distortion	may	appear	on	the	screen.	For...

22
Adjusting the vertical position of a projected image (Lens shift)
NOTE:
•	 Shifting	the	lens	to	the	maximum	in	two	directions	combined	will	cause	the	edges	of	the	image	to	become	dark	or	will	cause	
some shadows.
Adjusting with buttons on the cabinet
1. Press the LENS SHIFT/HOME POSITION button.
	 The	[LENS	SHIFT]	screen	will	be	displayed.	
2. Press the ▼▲◀ or ▶ button.
	 Use	the	▼▲◀▶	buttons	to	move	the	projected	image.
•	 Returning	the	lens	shift	position	to	the	home	position
	 Press	and	hold	the...

23
Adjusting with the remote control
1.	 Hold	the	CTL	button	and	press	the	ECO/L-SHIFT	button.
	 The	[LENS	SHIFT]	screen	will	be	displayed.	
2. Press the ▼▲◀ or ▶ button.
	 Use	the	▼▲◀▶	buttons	to	move	the	projected	image.
TIP:	
•	 The	figure	below	shows	the	lens	shift	ranges	(projection	mode:	desktop/front)	of	lens	units	NP-9LS08ZM1,	NP-9LS12ZM1,	NP-
9LS13ZM1,	NP-9LS16ZM1,	and	NP-9LS20ZM1.	For	NP-9LS40ZM1	check	page	158.
100%V50%V
20%V 20%V
20%V
20%V
50%V
100%H
11%H 11%H
11%H
11%HHeight	of	projected...

24
Focus
NOTE:
•	 For	lens	unit	NP-9LS08ZM1,	both	central	and	peripheral	focus	must	be	adjusted.	Use	theFOCUS	+/−buttons	to	adjust	the	central	
focus. If the peripheral focus is off, contact your dealer to have them \
adjust it.
1.	 Press	the	FOCUS	+/−	button.
•	 On	the	remote	control,	while	pressing	on	the	CTL	button,	press	on	VOL/FOCUS	(+)	or	(−)	button.
	 The	focus	is	adjusted.
TIP:	To	obtain	the	best	focus,	perform	the	following	(for	fixed	installation)
Preparation:	Warm	up	the	projector	for	one...

25
❻ Optimizing Computer Signal Automatically
Adjusting the Image Using Auto Adjust
When	an	image	from	HDMI	IN,	DisplayPort	IN,	BNC	input	terminal	(analog	RGB),	COMPUTER	IN,	or	HDBaseT	is	
being	projected,	and	the	edge	is	cut	off	or	the	image	quality	is	poor,	this	button	can	be	used	to	automatically	optimize	
the	projection	image	on	the	screen.
Press	the	AUTO	ADJ.	button	to	optimize	a	computer	image	automatically.
This	adjustment	may	be	necessary	when	you	connect	your	computer	
for	the	first	time....