NEC Projector Pe401h User Manual

							
64English ...

Appendices

 1
3
 2
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
 Lamp Replacing Procedure: 
  1.   Switch off the power to the projector by pressing the POWER OFF button on the 
remote control or the  button on the control panel.
  2. Allow the projector to cool down at least 60 minutes.
  3. Disconnect the power cord.
  4.    Use a screwdriver to loosen the screw on the lamp cover. 

	 5. Slide and remove the cover. 
  6. Loosen 2 screws on the lamp module and pull up the handle. 

  7.  Pull out the lamp module. 
x
  8.    Install the new lamp module by reversing the previous steps. Be sure to \
tighten 
the screws on the lamp module and the lamp cover.
  9.   After replacing the lamp, turn on the power, and select the [MENU] button -> 
OPTIONS |LAMP/FILTER SETTINGS -> CLEAR LAMP HOURS to reset the lamp usage hours. Refer to page 52.
Do not break the glass on the lamp module.Keep finger prints off the glass surface on the lamp module. Leaving finger prints on the glass surface might cause an unwanted shadow and poor picture quality.
4 
						

							
65... English

Appendices

Cleaning procedure for the lens
If the lens of projection lens is dusty or blemished, please clean 
it as following procedure:
1. Turn off the projector and cool projector down for a while.
2.  Unplug the power cord from outlet.
3.    Blow the dust by blower for cameras which you could buy from 
camera shops.Wipe the lens gently using a cleaning cloth.
 CAUTION:
•  Always wipe the lens with a cleaning cloth.
•  Please do not wipe the lens hard because that may cause serious damage 
on the surface of lens.
•  Wiping might scratch the lens. Optical performance of the projector will\
 
thus be impacted if lens is scratched after wiping. Optical performance \
impact will be dependent on the scratch condition of them.
•  Do not use liquid cleaners or chemicals on the cloth because it may con-
taminate the cloth and cause serious damage on the surface of lens. 
						

							
66English ...

Appendices

Specifications
OpticalNP-PE401H
Projection SystemSingle DLP® chip (0.65”, aspect ratio 16:9)
Resolution *11920 × 1080 pixels (1080P)
LensManual focus/manual zoom
F2.4 (wide): F3.29 (tele)
Lamp330W AC (248W in ECO mode)
Light Output *2 *34000 lumens
Approx. 75% in ECO mode
Contrast Ratio *3
(full white:full black) 2000:1 with DYNAMIC CONTRAST ON
Image Size (Diagonal)23 to 200 inches/0.58 to 5.08 m
Projection Distance (mini. - max.)32 to 474 inches/0.82 to 12.0 m
*1  Effective pixels are more than 99.99%.
*2   This is the light output value (lumens) when [Picture Mode] is set to \
[High-Bright] in the menu. If any other 
mode is selected as [Picture Mode], the light output value may drop slig\
htly.
*3   Compliance with ISO21118-200
ElectricalNP-PE401H
Inputs1 x RGB/Component (D-Sub 15P), 2 x HDMI (19P) HDCP supported *4, 1 x S-Video (DIN 4P), 1 x Video (RCA), 1 x (L/R) RCA Audio, 1 x Stereo Mini Au\
dio
Outputs1 x RGB (D-Sub 15P), 1 x Stereo Mini Audio
PC Control1 x PC Control Port (D-Sub 9P)
Wired LAN Port1 x RJ-45 (10/100 BASE-T)
Service Port1 x USB (for service purpose only)
Others1x USB (type A) for future use 
Color Reproduction1.07 billion colors simultaneously, Full color
Compatible Signals *5Analog:   VGA/SVGA/XGA/XGA+/WXGA/Quad-VGA/WXGA+/SXGA/SXGA+/WXGA+/WXGA++/UXGA/WSXGA+/HD/Full HD/ 480i/480p/576i/576p/720p/1080i/1080p
HDMI:   VGA/SVGA/XGA/WXGA/Quad-VGA/SXGA/SXGA+/WXGA+/
WXGA++/WSXGA+/ 480i/480p/576i/576p/720p/1080i/1080p 
Horizontal Resolution540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60300 TV lines: SECAM
Scan RateHorizontal: 30 kHz to 100 kHz (RGB: 24 kHz or over)Vertical: 50 Hz to 120 Hz (HDMI: 50 to 85 Hz)
Sync CompatibilitySeparate Sync
Built-in Speaker8W x 2 (monaural) 
						

							
67... English

Appendices

Power Requirement100 - 240V AC, 50/60 Hz
Input Current100 - 240V, 50-60Hz, 4.3-1.8A
Power Consumption(Typical value)
ECO Mode On310W (100-130V)/295W (200-240V)
ECO Mode Off410W (100-130V)/388W (200-240V)
Standby (Normal)12W (100-130V/200-240V)
Standby (Power-sav-ing)0.5W (100-130V/200-240V)
*4   HDMI
® (Deep Color, Lip Sync) with HDCP What is HDCP/HDCP technology? HDCP is an acronym for High-bandwidth Digital Content Protection. High b\
andwidth Digital Content Protec-tion (HDCP) is a system for preventing illegal copying of video data sent over a High-Definition Multimedia Interface (HDMI).  If you are unable to view material via the HDMI input, this does not nec\
essarily mean the projector is not functioning properly. With the implementation of HDCP, there may be case\
s in which certain content is pro-tected with HDCP and might not be displayed due to the decision/intentio\
n of the HDCP community (Digital Content Protection, LLC). Video: Deep Color; 8/10/12-bit, LipSync *5  An image with higher or lower resolution than the projector’s native \
resolution (1920 × 1080) will be displayed with scaling technology.
MechanicalNP-PE401H
Installation OrientationDesktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Dimensions13.8” (W) × 4.1” (H) × 11.1” (D) /350 mm (W) ×\
 105 mm (H) × 281 mm (D)  (not including protrusions)
13.8” (W) × 4.6” (H) × 14.8” (D) /350 mm (W) ×\
 117 mm (H) × 376 mm (D) (with cable cover and tilt foot)
Weight9.9 lbs/4.5 kg
Environmental Consid-erationsOperational Temperatures : 41° to 104°F (5° to 40°C),
(ECO mode selected automatically at 95°F to 104°F/35°C to 40°\
C)
20% to 80% humidity (non-condensing)
Storage Temperatures : 14° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
Operating altitude: 0 to 10000 ft/3000 m (HIG SPEED: 2500 feet/760 m to\
 10000 ft/3000 m) 
RegulationsUL/C-UL Approved (UL 60950-1, CSA 60950-1)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS CISPR.22 Class B
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)
ElectricalNP-PE401H 
						

							
68English ...

Appendices

Compatibility Modes
ModesResolution (dots)V.Frequency[Hz]H.Frequency[KHz]
VGA640x4806031.5
VGA640x4807237.9
VGA640x4807537.5
VGA640x4808543.3
SVGA800x6005635.1
SVGA800x6006037.9
SVGA800x6007248.1
SVGA800x6007546.9
SVGA800x6008553.7
XGA1024x7686048.4
XGA1024x7687056.5
XGA1024x7687560.0
XGA1024x7688568.7
XGA+1152x8647063.9
XGA+1152x8647567.5
XGA+1152x8648577.1
QuadVGA1280x9606060.0
SXGA1280x10246064.0
SXGA1280x10247580.0
SXGA1280x10248591.1
SXGA+1400x10506065.3
UXGA1600x12006075.0
IBM640x4806030.3
Apple, Mac II640x4806735.0
Apple, Mac II832x8647549.1
Apple, Mac II1152x8707568.7
(1) VGA Analog - PC Signal
 VGA Analog 
						

							
69... English

Appendices

(2) VGA Analog - Extended Wide timing
ModesResolution (dots)V.Frequency[Hz]H.Frequency[KHz]
HD1280x7206044.8
WXGA1280x7686047.8
WXGA1360x7686047.7
WXGA1366x7686047.7
WXGA+1440x9006055.9
WXGA++1600x9006059.9
WSXGA+1680x10506065.3
Full HD1920x1080(1080P)6067.5
(3) VGA Analog -Component Signal
ModesResolution (dots)V.Frequency[Hz]H.Frequency[KHz]
480i720x480(1440x480)59.94(29.97)15.7
576i720x576(1440x576)50(25)15.6
480p720x48059.9431.5
576p720x5765031.3
720p1280x7206045.0
720p1280x7205037.5
1080i1920x108060(30)33.8
1080i1920x108050(25)28.1
1080p1920x108023.97/24 27.0
1080p1920x10806067.5
1080p1920x10805056.3 
						

							
70English ...

Appendices

ModesResolution (dots)V.Frequency[Hz]H.Frequency[KHz]
VGA640x4806031.5
SVGA800x6006037.9
XGA1024x7686048.4
QuadVGA1280x9606060.0
SXGA1280x10246064.0
SXGA1280x10247580.0
SXGA+1400x10506065.3
(1) HDMI - PC Signal
 HDMI Digital
(2) HDMI - Extended Wide timing
ModesResolution (dots)V.Frequency[Hz]H.Frequency[KHz]
HD1280x7206044.8
HD1280x72012092.9
WXGA1280x7686047.8
WXGA1280x8006049.6
WXGA1360x7686047.7
WXGA1366x7686047.7
WXGA+1440x9006059.9
WXGA++1600x9006059.9
WSXGA+1680x10506065.3
Full HD1920x1080(1080P)6067.5 
						

							
71... English

Appendices

(3) HDMI - Video Signal
ModesResolution (dots)V.Frequency[Hz]H.Frequency[KHz]
480i720x480(1440x480)59.94(29.97)15.7
576i720x576(1440x576)50(25)15.6
480p640x48059.9431.5
480p720x48059.9431.5
576p720x5765031.3
720p1280x7206045.0
720p1280x7205037.5
1080i1920x108060(30)33.8
1080i1920x108050(25)28.1
1080p1920x108023.97/24 27.0
1080p1920x10806067.5
1080p1920x10805056.3
(4) HDMI – 1.4a 3D Timing
ModesResolution (dots)V.Frequency[Hz]H.Frequency[KHz]
720p (Frame Packing)1280x720 5037.5
720p (Frame Packing)1280x720 6045.0
1080p (Frame Packing )1920x10802427.0
720p (Top and Bottom )1280x7205037.5
720p (Top and Bottom )1280x7206045.0
1080i (Top and Bottom)1920x108050(25)28.1
1080i (Top and Bottom)1920x108060(30)33.8
1080p (Top and Bottom)1920x10802427.0
1080p (Top and Bottom)1920x10805056.3
1080p (Top and Bottom)1920x10806067.5
720p (Side by Side (Half))1280x7206045.0
1080i (Side by Side (Half))1920x108050(25)28.1
1080i (Side by Side (Half))1920x108060(30)33.8
1080p (Side by Side (Half))1920x10805056.3
1080p (Side by Side (Half))1920x10806067.5
Graphic source monitor range limitsHorizontal scan rate:30k-100kHz
Vertical scan rate:50-120Hz
Max. pixel rateAnalog:162MHz Digital:165MHz 
						

							
72English ...

Appendices

TIP:
•  An image with higher or lower resolution than the projector’s native \
resolution (1920 × 1080 ) will be displayed with scaling technology.
•  
Sync on Green and Composite sync signals are not supported.
•  
Signals other than those specified in the table above may not be displayed 
correctly. If this should happen, change the refresh rate or resolution \
on 
your PC. Refer to Display Properties help section of your PC for proce-
dures. 
						

							
73... English

Appendices

Please note that dam-age resulting from incorrect installation will invalidate the war-ranty.
Ceiling Mount Installation
1. To prevent damaging your projector, please use the ceil-
ing mount package for installation.
2.  If you buy a ceiling mount from another company, please 
ensure the screws used to attached a mount to the projec-
tor met the following specifications:
  Screw type: M4
  Maximum screw length: 8mm
  Minimum screw length: 6mm
Warning: 
1.  If you buy a ceiling 
mount from another 
company, please ensure that there is at least 10cm distance between the bottom cover of the projector and the ceiling.
2.   Avoid placing 
the projector near sources of heat such air-conditioning units and heaters otherwise it may overheat and shut down automatically.
3.   Ceiling mounts 
should be attached to metal, concrete or wood.
213.5 (8.4)
130.0 (5.1)
150.0 (5.9)
213.5 (8.4)
38.5
(1.5)
195.0 (7.7)175.0 (6.9)138.0 (5.4)5.0 (0.2)
115.0 (4.5)
165.0 (6.5)
4-M4*L8 (Max)
for Ceiling Mount
Unit: mm (inch)