NEC Projector Pe401h User Manual

							
44English ...

User Controls

  PHASE 
Synchronize the signal timing of the display with the graphic card. 
If the image appears to be unstable or fl  ickers, use this function to 
correct it.
  CLOCK
Change the display data frequency to match the frequency of 
your computer’s graphic card. Use this function only if the image 
appears to fl  icker vertically.
  H. POSITION
 Press the  button to move the image left.
 Press the  button to move the image right. 
  V. POSITION
 Press the  button to move the image down.
 Press the  button to move the image up. 
	“SIGNAL” is only supported in Analog VGA (RGB) signal.
 
SETTING | 
SIGNAL 
						

							
45... English

User Controls

  LOGO
Use this function to display the startup screen (NEC logo).
 ON: Displays the NEC logo.
 OFF: Not display the NEC logo.
  PC CONTROL MODE
  PC CONTROL: Allow PC control of an individual projector. 
(default setting)
  LAN: Allow projector control via web browser (Internet 
Explorer) using the network.
  NETWORK
Refer to pages 48-50.
  CLOSED CAPTION
Use this function to enable close caption and activate the closed 
caption menu. Select an appropriate closed captions option: OFF, 
CC1, CC2, CC3, CC4, T1, T2, T3 and T4.
	When “POWER-SAVING” is select-ed for “STANDBY MODE” from the menu, the projec-tor cannot be con-trolled in standby mode from exter-nal equipment.
SETTING | 
ADVANCED 
						

							
46English ...

User Controls

  SECURITY TIMER
Use this function to set how long (MONTH/DAY/HOUR) the 
projector can be used. Once this time has elapsed you will be  
requested to enter your password again.
 
SETTING | 
ADVANCED | 
SECURITY
  SECURITY
 OFF: Choose “OFF” to be able to switch on the projector with-
out password verifi  cation.
 ON: Choose “ON” to use security verifi  cation when turning on 
the projector.
 
■ First Time: 
1. The Password is 4 digits, default value is “1234”. (fi  rst time)
2. Use number buttons on the remote to enter your password, 
and then press ENTER to confi  rm your password. 
						

							
47... English

User Controls

  CHANGE PASSWORD
1.  Press ENTER to enter SECURITY KEYWORD setting.
2.  The password has to be 4 digits.  
Current password
3.  Use number buttons on the remote control, to enter your 
old password and then press ENTER to confi  rm your 
password.
Input new password 
4.  Use number buttons on the remote control, to enter your 
new password and then press ENTER to confi  rm your 
password. 
 Confi  rm new password 
5.  Enter the new password again and press ENTER to 
confi  rm. 
 If the incorrect password is entered 3 times, the projector will 
automatically shut down. (When turn on the projector.)
 If you have forgotten your password, please contact your local 
offi  ce for support.
	Password default value is “1234” (fi  rst time). 
						

							
48English ...

User Controls

  NETWORK STATUS
Display the network connection status. (default: DISCONNECT)
  DHCP
Use this function to select your desired startup screen. If you 
change the setting from one to another, when you exit the OSD 
menu, the new setting will take effect on next open.
 ON: Assign an IP address to the projector from an external 
DHCP server automatically.
 OFF: Assign an IP address manually.
  IP ADDRESS
Select an IP address.
  SUBNET MASK
Select subnet mask number.
  GATEWAY
Select the default gateway of the network connected to the 
projector.
  APPLY
Press ENTER to apply the selection. 
SETTING | 
ADVANCED | 
NETWORK 
						

							
49... English

User Controls

1.  Turn on DHCP to allow the DHCP server to automatically assign 
an IP, or manually enter the required network information.
2.  Then choose apply and press ENTER button to complete the 
confi  guration process.
3.  Open your web browser and type in from the OSD LAN screen 
then the web page will display as below:
4. Open “Projector Status and Control” to control your projector. 
 
When making a direct connection from your computer to the 
projector
Step 1: Find an IP Address (default:192.168.0.10) from LAN 
function of projector.
192.168.0.10
 How to use web browser to control your projector
	When you used the projector IP address, you can not link to your service server.
	PJLink:  Set a pass-word for PJLink. 
PJLink is a stan-dardization of protocol used for controlling projec-tors of different manufacturers. This standard protocol is established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.
The projector supports all the commands of PJLink Class 1.
	AMX BEACON:
Turn on or off for detection from AMX Device Discovery when connecting to the network sup-ported by AMX's NetLinx control system.
	CRESTRON ROOM-VIEW compatibility:
The projector sup-ports CRESTRON ROOMVIEW, allow-ing multiple devices connected in the network to be man-aged and controlled from a computer or a controller.
For more informa-tion, visit http://www.crestron.com 
						

							
50English ...

User Controls

Step 2: Select apply and press the ENTER button on the remote control or the control 
panel to submit function or press the MENU button on the remote control or 
the control panel to exit.
Step 3: To open Network Connections, click Start, click Control Panel, click Network 
and Internet Connections, and then click Network Connections. Click the connection you want to configure, and then, under Network Tasks  , click Change settings of this connection.
Step 4: On the General tab, under This 
connection uses the following 
items, click Internet Protocol 
(TCP/IP), and then click 
“Properties.”
Step 5: Click Use the following IP 
address, and type in as below:
1) IP address: 192.168.0.10 
2) Subnet mask: 255.255.255.0
3) Default gateway:192.168.0.1
Step 6: To open Internet Options, click 
IE web browser, click Internet Options, click the Connections tab and click “LAN Settings...” 
Step 7: The Local Area Network (LAN) 
Setting dialog box appears, In 
the Proxy Server area, cancel the Use a proxy server for your LAN check box., then click “OK” button 
twice.
Step 8: Open your IE and type in the IP 
address of 192.168.0.10 in the URL 
then press the ENTER button key. 
 
Step 9: Open “Projector Status and 
Control” to control your projector. 
						

							
51... English

User Controls

  INPUT SEARCH
 ON: The projector will search for other signals if the current input signal is lost. 
 OFF: The projector will only search current input connection.
  INPUT
Use this option to enable / disable input sources. Press ENTER to 
enter the sub menu and select which sources you require. Press 
the ENTER button to finalize the selection. The projector will not 
search for inputs that are not selected. 
  FAN MODE
  AUTO: The built-in fans automatically run at a variable speed 
according to the internal temperature.
  HIGH SPEED: The built-in fans run at high speed.
Select this option when using the projector at altitudes 
approximately 2500 feet/760 meters or higher.
  INFORMATION HIDE
 ON: Choose “ON” to hide the info message.
 OFF: Choose “OFF” to show the “SEARCHING” message.
  BACKGROUND COLOR
Use this feature to display a “BLACK”or “BLUE” screen when n\
o 
signal is available.
  RESET
Choose “YES” to return the display parameters on all menus to 
the factory default settings.
	With the optional dust fi  lter installed, “HIGH SPEED” is selected for “FAN MODE”. Dust fi  lter is Optional and may not be required in some regions.
 
OPTIONS | 
GENERAL 
						

							
52English ...

User Controls

  LAMP LIFE REMAINING
Showing the Lamp life.
  LAMP HOURS USED
Display the projection time.
  FILTER HOURS USED
Display the fi  lter used time.
  ECO MODE
Choose “ECO” to dim the projector lamp which will lower power 
consumption and extend the lamp life. Choose “OFF” to return to 
normal mode.
  LAMP LIFE REMINDER
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed. 
The message will appear when the lamp has reached the end of its 
life. 
  FILTER USAGE HOURS
Display the time preference between displaying the message for 
cleaning the fi  lter. Clean the fi  lter when you get the message .
When "000[H]" is set, the message will not be displayed. 
  CLEAR LAMP HOURS
Reset the lamp hour counter after replacing the lamp.
  CLEAR FILTER HOURS
Reset the fi  lter hour counter after replacing the fi  lter.
OPTIONS | 
LAMP/FILTER 
SETTINGS 
						

							
53... English

User Controls

  INFORMATION
To display the projector information for source, resolution, and 
software version on the screen.
OPTIONS | 
INFORMATION