NEC Projector NP3150/NP2150/NP1150 User Manual

8
6. Using On-Screen Menu
Selecting Cornerstone mode [CORNERSTONE]
 
This option allows you to correct trapezoidal distortion.
Selecting this item will display the Cornerstone adjustment screen. (→ page 39)
NOTE: When [KEYSTONE] is selected, [CORNERSTONE] is not available.
Using the pIp Function
This function allows you to view two different signals simultaneously.
PIP POSITION: 
This option allows you to select the position of a sub picture in the main picture.
The options are: top-left,...

88
6. Using On-Screen Menu
Using the Wall Color Correction [WALL COLOR]
 
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following nine options are available.
Setting Lamp mode to Normal or Eco [LAmp mODE]
This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be 
extended by using the Eco mode. Selecting Eco mode decreases fan noise when compared to Normal mode.
NOTE: If the...

89
6. Using On-Screen Menu
Using Off Timer [OFF TImER]
1. Select your desired time between 30 minutes and 16 hours: OFF, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2.  Press the ENTER button on the remote control.
3.  The remaining time starts counting down.
4.  The projector will turn off after the countdown is complete.
NOTE:
•  To cancel the preset time, set [OFF] for the preset time or turn off the power.
• When the remaining time reaches 3 minutes before the projector is turned off, the [THE...

90
6. Using On-Screen Menu
Logging Off Your projector [LOGOFF]
This feature allows you to log off your projector without turning it off.
Logging off your projector will prevent an unauthorized user from operating your projector.
To log off your projector, follow the steps below.
1. Press the MENU button and use the SELECT  button to highlight [SETUP].
 
2.   Use the SELECT  or the ENTER button to highlight [BASIC].
 
3. Use the SELECT  button to highlight [LOGOFF], and press the ENTER button.
  the...

91
6. Using On-Screen Menu
[MENU]
Selecting menu Color [COLOR SELECT]
You can choose between two options for menu color: color and monochrome.
Turning  On  /  Off  Source  Display, message  and Time  [SOURCE  DISpLAY],  [mESSAGE  DISpLAY], 
[TImE DISpLAY]
SOURCE.DISPLAy.........
This.option. turns.on.or.off. input. name. display. such.as.Computer. 1,.Computer. 2,.Computer. 3,.Compo-
nent,.Video,.and.No.Input.to.be.displayed.on.the.top.right.of.the.screen.
MESSAGE.DISPLA y.............

9
6. Using On-Screen Menu
[INSTALLATION]
Selecting projector Orientation [ORIENTATION]
This  reorients  your  image  for  your  type  of  projection. The  options  are:  desktop  front  projection,  ceiling  rear  projec-
tion, desktop rear projection, and ceiling front projection.
DESKTOP FRONTCEILING REAR
DESKTOP REARCEILING FRONT 

9
Selecting Aspect Ratio and position for Screen [SCREEN]
SCREEN.TyPE........Select.one.of.two. options:. 4:3.SCREEN. or.WIDE. SCREEN. for.the. screen. to.be. used.. See.also. [ASPECT.
RATIO].
(→.page.83)
POSITION...............This.feature. allows.you.to.adjust. the.vertical. position. of.the. image. when.WIDE. SCREEN. has.been. selected.
for.the.screen.type.
When.WIDE.SCREEN.has.been.selected.there.is.no-signal.area.above.and.below.the.image.
NOTE: This option is available only when [WIDE SCREEN]...

94
Setting Security [SECURITY SETTINGS]
Disabling the Cabinet Buttons [CONTROL pANEL LOCK]
This option turns on or off the Control Panel Lock function.
NOTE:
• This Control Panel Lock does not affect the remote control functions.
• When  the  control  panel  is  locked,  pressing  and  holding  the  EXIT  button  on  the  projector  cabinet  for  about  10  seconds  will 
change the setting to [OFF].
Setting a p assword [LOGO LOCK]
A password can be set for your projector to avoid operation by an...

95
6. Using On-Screen Menu
2. Type the same password again and press the ENTER button.
  Your password will be assigned.
[DELETE] 
To delete your password:
1. Select [DELETE PASSWORD] and press the ENTER button.
2.  Enter your password.
  An asterisk will be displayed.
3. Press the ENTER button.
  Your password will be deleted.
NOTE: 
* Do not forget your password. However, if you forget your keyword, NEC or your dealer will provide you with your Release Code 
upon proof of ownership.
* The [LOGO LOCK]...

9
6. Using On-Screen Menu
[SECURITY]
The Security function enables you to protect your projector so that the projector will not project a signal unless you 
enter a keyword. There is also an option to lock the projector by using a registered USB memory* as a protect key. 
Once you have registered your USB memory as a protect key, you are required to insert the registered USB mem-
ory  into  the  USB  port  of  the  projector  each  time  you  turn  on  the  projector. You  can  enable  the...