Home > NEC > Projector > NEC Np510 Portable Projector User Manual

NEC Np510 Portable Projector User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual NEC Np510 Portable Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							32
    3. Projecting an Image (Basic Operation)
    FOCUS FOCUS
    Zoom
    [NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W]
    Use	the	ZOOM	lever	to	adjust	the	image	size	on	the	screen.
    Zoom Lever
    [NP610S/NP510WS]
    The	image	size	can	be	adjusted	electronically	from	the	menu. 	To	do	so,	follow	the	steps	below.
    Adjusting from the menu
    1.  Press the MENU button.
      The menu will be displayed.
    2. Press the  button to select [SETUP] and press the ENTER button.
      The [GENERAL] tab will be highlighted.
     
    3. Press the  button.
      The [DIGITAL ZOOM] will be highlighted.
      
    						
    							33
    3. Projecting an Image (Basic Operation)
    4. Use the  or  button to adjust the image size.
    5.  After completing adjustment, press the EXIT button three times.
      The menu will be closed.
    Focus
    [NP610/NP510/NP410/NP405/NP310/NP305/NP510W/NP410W]
    Use	the	FOCUS	ring	to	obtain	the	best	focus.
    [NP610S/NP510WS]
    Use	the	FOCUS	lever	to	obtain	the	best	focus.
    FO CUS FOCUS
    Focus Ring
    FOCUSFOCUS
    Focus Lever 
    						
    							34
    3. Projecting an Image (Basic Operation)
     Correcting Keystone Distortion
    Correcting Keystone Distortion
    If	the	screen	is	tilted	vertically,	keystone	distortion	becomes	large.	Proceed	with	the	following
    steps	to	correct	keystone	distortion
     
    NOTE: 
    •	 The	Keystone	correction	can	cause	an	image	to	be	slightly	blurred	because	the	correction	is	made	electronically.
    •	 The	Keystone	correction	range	can	be	made	narrower,	depending	on	a	signal	or	its	aspect	ratio	selection.
    Adjusting with buttons on the cabinet
    1. Press the  or  button with no menus displayed.
    	 The	keystone	bar	will	be	displayed.
        
    MENU
    EXITENTER
    ST ATUS
    LAMP
    AUTO ADJ.
    SOURCE
    2.  Use the  or  to correct the keystone distortion.
    	 The	keystone	bar	will	be	closed	after	a	period	of	time.
    3.  Press the ENTER button.
    	 The	keystone	bar	will	be	closed.
    NOTE:	 When	the	menu	 is	displayed,	 the	above	 operation	 is	not	 available.	 When	the	menu	 is	displayed,	 press	the	MENU	 button	 to	
    close	the	menu	and	start	the	Keystone	correction.
    From	the	menu,	 select	[SETUP]	→	[GENERAL]	→	[KEYSTONE].	 The	changes	 can	be	saved	 with	[KEYSTONE	 SAVE].	(→ page  36, 
    68) 
    						
    							35
    3. Projecting an Image (Basic Operation)
    Adjusting from the menu
    1. Press the MENU button.
      The menu will be displayed.
    2. Press the  button to select [SETUP] and press the ENTER button.
     
      The [GENERAL] screen will be displayed.
    3. Press the  button to select [KEYSTONE].
     
    4.  Press the  or  button.
      Adjust so that the image is rectangular.
    5. After completing adjustment, press the EXIT button three times.
      The menu will be closed.
    NOTE:	The	Keystone	correction	can	cause	an	image	to	be	slightly	blurred	because	the	correction	is	made	electronically.
    TIP:	The	changes	can	be	saved	with	[KEYSTONE	SAVE].	(→ page 36, 68) 
    						
    							36
    3. Projecting an Image (Basic Operation)
    Adjusting with the Auto Keystone Function
    The	Auto	 Keystone	 correction	 feature	will	correct	 the	vertical	 distortion	 of	a	projected	 image	on	the	 screen. 	No	 special	
    operation	required. 	Just	put	the	projector	on	a	flat	surface.
    TIP:	Even	when	the	menu	setting	for	[AUTO	KEYSTONE]	is	turned	on,	[KEYSTONE]	can	be	adjusted	manually.
    To	turn	on	[AUTO	KEYSTONE],	proceed	the	following	steps.
    1. Press the MENU button
      The menu will be displayed.
    2. Press the  button to select [SETUP] and press the ENTER button.
      The [GENERAL] screen will be highlighted.
    3. Press the  button.
      The [AUTO KEYSTONE] will be highlighted.
    4. Press the ENTER button to display the [AUTO KEYSTONE] screen.
    5.  Press the  or  button to select [ON] and press the ENTER button.
    6.  Press the MENU button.
      The menu will be closed.
    NOTE:
    •	 The 	maximum 	range 	of 	vertical 	keystone 	correction 	is 	+/−30 	degrees 	on 	the 	NP610/NP510/NP410/NP405/NP310/NP305/NP510W/
    NP410W	and	+/−20	degrees	on	the	NP610S/NP510WS.	
    	 The	maximum	range	of	keystone	correction	may	be	lower	depending	on	the	signal	or	aspect	ratio	selection.
    	 The	range	of	keystone	correction	is	not	the	maximum	tilt	angle	of	projector.
    •	 The	Auto	Keystone	correction	will	take	effect	in	2	seconds	after	changing	the	projection	angle	during	projection.
    •	 The	left	and	right	(horizontal)	keystone	correction	is	not	available.
      Place the projector so that the lens surface is parallel to the screen.
     The rear feet of the projector can be adjusted to level the projector.
    •	 Using	keystone	correction	can	cause	the	image	to	be	slightly	blurred	because	the	correction	is	made	electronically.
    TIP:	If	you	have	one	of	the	following	conditions,	the	projector’s	Auto	Keystone	may	not	be	performed	correctly.
    •	 The	screen	is	tilted
    •	 The	room	temperature	is	too	high	or	too	low
    •	 The	optical	zoom	is	maximized	or	minimized 
    						
    							37
    3. Projecting an Image (Basic Operation)
     Optimizing Computer Signal Automatically
    Adjusting the Image Using Auto Adjust
    Optimizing	a	computer	image	automatically.
    Press	the	AUTO	ADJ.	button	to	optimize	a	computer	image	automatically.
    This	adjustment	may	be	necessary	when	you	connect	your	computer	for	the	first	time.
    [Poor picture]
    [Normal picture]
    VOLUMEL-CLICK
    MOUSER-CLICK
    ASPECT HELP FREEZE
    PICTURE
    AUTO ADJ.S-VIDEO VIDEOCOMPUTER
    ECO MODE12
    Increase volume
    Decrease volume
    VOLUME L-CLICK
    MOUSER-CLICK
    ASPECT HELP FREEZE
    PICTURE
    AUTO ADJ.S-VIDEO VIDEOCOMPUTER
    ECO MODE12
    NOTE:
    Some signals may take time to display or may not be displayed correctly.
    •	 The	Auto	Adjust	function	does	not	work	for	component,	video,	and	DVI	digital	signals.
    •	 If 	the 	Auto 	Adjust 	operation 	cannot 	optimize 	the 	computer 	signal, 	try 	to 	adjust 	[HORIZONTAL], 	[VERTICAL], 	[CLOCK], 	and 	[PHASE]	
    manually.	(→ page 64, 65)
     Turning Up or Down Volume
    Sound	level	from	the	speaker	can	be	adjusted.
    TIP: When no menus appear, the  and  buttons on the projector cabinet work as a volume control. 
    MENU
    EXITENTER
    ST ATUS
    LAMP
    AUTO ADJ.
    SOURCE
    MENU
    EXITENTER
    ST ATUS
    LAMP
    AUTO ADJ.
    SOURCE 
    						
    							38
    3. Projecting an Image (Basic Operation)
    7 Turning off the Projector
    MENU
    EXITENTER
    STATUS
    LAMP
    AUTO ADJ.
    SOURCEENTEREXIT
    MENU
    UP
    MAGNIFY
    PAGE
    OFF
    POWER ON
    AV-MUTE
    DOWN
    To	turn	off	the	projector:
    1.  First,  press  the   (POWER)  button  on  the  projector 
    cabinet or the POWER OFF button on the remote con -
    trol. 
      The  [POWER  OFF  /  ARE YOU  SURE?  /  CARBON  SAV-
    INGS- SESSION 0.000[g-CO2]] message will appear.
    2.  Secondly,  press  the  ENTER  button  or  press  the  
    (POWER) or the POWER OFF button again.
      The lamp will turn off and the projector will go into standby 
    mode. When  in  standby  mode,  the  POWER  indicator  will 
    light orange and the STATUS indicator will light green when 
    [NORMAL] is selected for [STANDBY MODE]. 
     Immediately after turning on the projector and displaying an 
    image, you cannot turn off the projector for 60 seconds.
    3. Finally, turn off the Main Power switch. 
      The POWER indicator will go out.
    NOTE:	 Do	not	 turn	 off	the	 main	 power	 within	10	seconds	 of	making	
    adjustment or setting changes and closing the menu.
    Doing	so	can	cause	loss	of	adjustments	and	settings.
     
    Power	On
    Steady green 
    light
    CAUTION:
    Parts	 of	the	 projector	 will	become	 heated	during	operation. 	Use	 caution	 when	picking	 up	the	 projector	 immediately	
    after it has been operating.
    CAUTION:
    The	 projector	 cannot	be	turned	 off	for	 60	seconds	 after	the	lamp	 is	turned	 on	and	 while	 the	POWER	 indicator	 is	
    blinking	green. 	Doing	so	could	cause	premature	lamp	failure.
    Standby
    Steady  
    orange light 
    						
    							39
    3. Projecting an Image (Basic Operation)
     After Use
    Preparation:	Make	sure	that	the	projector	is	turned	off.
    1. Unplug the power cable.
    2.  Disconnect any other cables.
    3.  Retract adjustable tilt foot if extended.
    4.  Cover the lens with the lens cap.
    5.  Put the projector and accessories in the supplied soft case.
      Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from 
    damage.
    NOTE:	The	NP610S,	the	NP510WS,	the	NP405,	and	the	NP305	do	not	come	with	a	soft	case.
    NOTE:	 When	placing	 the	projector	 in	the	 soft	 case,	 retract	 the	tilt	foot	 and	the	rear	 feet.	 Failure	 to	do	 so	may	 case	 damage	 to	the	
    projector.
    CAUTION:
    Use	caution	 when	putting	 the	projector	 in	the	 soft	 case	 immediately	 after	the	projector	 has	been	 operating. 	The	
    projector cabinet is hot.
    Insert the projector with the lens facing upward 
    						
    							40
    1 Turning off the Image and Sound
    Press	the	AV-MUTE	 button	to	turn	 off	the	 image	 and	sound	 for	a	short	
    period of time. Press again to restore the image and sound.
    NOTE:
    •	 Even though the image is turned off, the menu still remains on the scree\
    n.
    •	 Sound	from	the	AUDIO	OUT	jack	(Stereo	mini)	can	be	turned	off.
     Freezing a Picture
    Press	 the	FREEZE	 button	to	freeze	 a	picture. 	Press	 again	to	resume	
    motion.
    NOTE:	The	image	is	frozen	but	the	original	video	is	still	playing	back.
     Enlarging a Picture
    You	can	enlarge	the	picture	up	to	four	times.
    NOTE:	 The	maximum	 magnification	 may	be	less	 than	 four	times	 depending	 on	
    the signal.
    To	do	so:
    1. Press the MAGNIFY (+) button to magnify the picture.
      To move the magnified image, use the ,, or  button.
    4. Convenient Features
    ENTEREXIT
    MENU
    UP
    MAGNIFY
    PAGE
    OFF
    POWER ON
    AV-MUTE
    DOWN
    ENTEREXIT
    MENU
    UP
    MAGNIFY
    PAGE
    OFF
    POWER ON
    AV-MUTE
    DOWN
    ENTEREXIT
    MENU
    UP
    MAGNIFY
    PAGE
    OFF
    POWER ON
    AV-MUTE
    DOWN
    VOLUME L-CLICK
    MOUSER-CLICK
    ASPECT HELP FREEZE
    PICTURE
    AUTO ADJ.S-VIDEO VIDEOCOMPUTER
    ECO MODE12 
    						
    							41
    4. Convenient Features
     Changing Eco Mode
    This	feature	enables	you	to	select	two	brightness	modes	of	the	lamp:
    OFF	and	ON	modes.	The	lamp	life	can	be	extended	by	turning	on	the	[ECO	MODE].
    [ECO	MODE]DescriptionStatus	of	LAMP	indicator
    [OFF]This	is	the	default	setting	(100%	Brightness).Off
    ST ATUS
    LAMP
    [ON]Select this mode to increase the lamp life (approx. 
    70%	
    Brightness	 on	NP610/NP510W/NP410W/
    NP610S/NP510WS 	and 	approx. 	80% 	Brightness	 on	
    NP510/NP410/NP405/NP310/NP305). Steady Green light
    ST
    ATUS
    LAMP
    To	turn	on	the	[ECO	MODE],	do	the	following:
    	
    1. Press the ECO MODE button on the remote control to display [ECO MODE] screen.
    2.  Use the  or  button to select [ON].
    3.  Press the ENTER button. 
    	 To	change	from	[ON]	to	[OFF],	Go	back	to	Step	2	and	select	[OFF]. 	Repeat	Step	3.
    NOTE: 
    •	 The	[ECO	MODE]	can	be	changed	by	using	the	menu.
    	 Select	[SETUP]	→	[GENERAL]	→	[ECO	MODE].
    •	 The	lamp	life	remaining	and	lamp	hours	used	can	be	checked	in	[USAGE	TIME].	Select	[INFO.]	→[USAGE	TIME].
    •	 The	projector	 is	always	 in	[ON]	 for	90	seconds	 after	the	lamp	 is	turned	 on	and	 while	 the	POWER	 indicator	 is	blinking	 green.	The	
    lamp	condition	will	not	be	affected	even	when	[ECO	MODE]	is	changed.
    •	 After	 a	lapse	 of	1	minute	 from	when	 the	projector	 displays	a	blue,	 black	 or	logo	 screen,	 [ECO	MODE]	 will	automatically	 switch	to	
    [ON].	The	projector	will	return	to	the	[OFF]	once	a	signal	is	accepted.
    •	 If	the	projector	 is	overheated	 in	[OFF]	 mode,	 there	may	be	a	case	 where	 the	[ECO	 MODE]	 automatically	 changes	to	[ON]	 mode	
    to	protect	 the	projector.	 When	the	projector	 is	in	 [ON]	 mode,	 the	picture	 brightness	 decreases.	 When	the	projector	 comes	back	
    to	normal	temperature,	the	[ECO	MODE]	returns	to	[OFF]	mode.
     Thermometer symbol [ 	]	 indicates	 the	[ECO	 MODE]	 is	automatically	 set	to	[ON]	 mode	 because	 the	internal	 temperature	 is	too	
    high.
    2. Press the  button.
      The area of the magnified image will be moved
    3. Press the MAGNIFY (−) button.
      Each  time  the  MAGNIFY  (−)  button  is  pressed,  the  image  is  re-
    duced.
    NOTE: 
    •	 The	image	will	be	enlarged	or	reduced	at	the	center	of	the	screen.
    •	 Displaying	the	menu	will	cancel	the	current	magnification.ENTEREXIT
    MENU
    UP
    MAGNIFY
    PAGE
    OFF
    POWER ON
    AV-MUTE
    DOWN 
    						
    All NEC manuals Comments (0)

    Related Manuals for NEC Np510 Portable Projector User Manual