NEC Neax 2400 Ipx System Operations And Maintenance Manual
Here you can view all the pages of manual NEC Neax 2400 Ipx System Operations And Maintenance Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 531
NDA-24307 CHAPTER 6 Page 503 Issue 1 SYSTEM OPERATIONS (3) Designated Connection Test Procedure (a) Register Test Procedure Figure 6-29 Register Test Procedure/Connection Diagram Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Route numbers to be designated are as follows.: If any of the dialed numbers are not received correctly, a Reorder Tone (ROT) is heard. RT NUMBER 902 903 TRUNK NAME Originating Register Trunk Incoming Register Trunk Hang Up TRUNK DESIGNATIONTEST IN PROGRESS...
Page 532
CHAPTER 6 NDA-24307 Page 504 Issue 1 SYSTEM OPERATIONS (b) Sender Test Procedure Figure 6-30 Sender Test Procedure/Connection Diagram Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Route number to be designated is as follows: If any of the dialed numbers are received correctly, a Reorder Tone (ROT) is heard. RT NUMBER 905 TRUNK NAME Sender Trunk DP/PB Note 1:After the sender to be tested is connected to the register, the sender sends out 1 ~ 9, 0 by DP signals and 1 ~ 9, 0, *, # by...
Page 533
NDA-24307 CHAPTER 6 Page 505 Issue 1 SYSTEM OPERATIONS (c) 3-Party Conference Trunk Test Procedure Figure 6-31 3-Party Conference Test Procedure Note:If the trunk number of the next 3-Party Conference Trunk is not assigned, the test ends. Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Route numbers to be designated are as follows: RT NUMBER 909 913 TRUNK NAME 3-party conference trunk (for station, ATTCON, trunk) 3-party conference trunk (only for ATTCON) + “9xx” RT No.“xxx” TRK No....
Page 534
CHAPTER 6 NDA-24307 Page 506 Issue 1 SYSTEM OPERATIONS Figure 6-32 3-Party Conference Test Connection Diagram TSTT TSTT TSTTTSTT TSTT TSTT ORTSST TRUNK DESIGNATION TEST IN PROGRESS 1 SEC.1 SEC.1 SEC.1 SEC. 1 SEC. 1 SEC. 1 SEC. 1 SEC. (DT) (SST) (DT) (SST) (DT) (SST)
Page 535
NDA-24307 CHAPTER 6 Page 507 Issue 1 SYSTEM OPERATIONS (d) Tone Test Procedure Figure 6-33 Tone Test Procedure/Connection Diagram Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 For Tone No. to be designated, refer to Table 6-7. Tone designated by Tone No. is heard. Lift handset (Tone) Dial access code for designated connection Dial “x x” Tone Number Dial “000” (DT) Hang Up(DT)TRUNK DESIGNATIONTEST IN PROGRESS ORT ORTTONE
Page 536
CHAPTER 6 NDA-24307 Page 508 Issue 1 SYSTEM OPERATIONS Table 6-7 Tone Numbers Tone No. Kind Of Tone Remarks 00 Dial Tone (DT) 01 Special Dial Tone (SPDT) 02 Ring Back Tone (RBT) 03Continuous Ring Back Tone (CRBT) 04 Busy Tone (BT) 05 Reorder Tone (ROT) 06 Service Set Tone (SST) 07 Second Dial Tone (SDT) 08 No Tone 09 Sender Transmitting Tone (SDTT) 10 Call Waiting Ring Back Tone (CWRBT) 11 No Tone 12 No Tone 1 3 Te s t To n e ( T S T T ) 14 Music On Hold (MSC) 15 No Tone
Page 537
NDA-24307 CHAPTER 6 Page 509 Issue 1 SYSTEM OPERATIONS (e) Interrupt Ringing (IR) Test Procedure Figure 6-34 Interrupt Ringing (IR) Test Procedure/Connection Diagram AAA A ORTIR SST Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 Lift handset Dial access code for designated connection (SST) (DT) TEST IN PROGRESSDESIGNATION Dial “999” Hang Up Bell Rings Lift handset and answer (SST) Hang Up HANGUPSST ANSWER
Page 538
CHAPTER 6 NDA-24307 Page 510 Issue 1 SYSTEM OPERATIONS (f) Trunk Test Procedure Figure 6-35 Trunk Test Procedure Note:If the trunk number of the next trunk is not assigned, the test ends. Access code is assigned by ASPA command, CI=N, SRV=SSC, SID=17 + “9xx” RT No.“xxx” TRK No. Lift handset Is next register to be tested, too? Make switch hook flash Note (DT) Dial access code for designated connection (RBT) YESNO Dial the called party number The called party at the distant office answers and talks...
Page 539
NDA-24307 CHAPTER 6 Page 511 Issue 1 SYSTEM OPERATIONS Figure 6-36 Trunk Test Connection Diagram A ORT TRUNK DESIGNATIONCALLED PARTY DIALINGCALLED PARTY DIALING NUMBER SENDINGCALLED PARTY DIALING TRKA AA A A2nd DT SYSTEM CHARGING SERVICE PROVIDED SENDER SYSTEM SND TRK ORT ORT TRK
Page 540
CHAPTER 6 NDA-24307 Page 512 Issue 1 SYSTEM OPERATIONS 10.2 Designated Connection Test (DESKCON/ATTCON) (1) General The purpose of this test is to confirm the operations related to a trunk which has been designated from the DESKCON/ATTCON. (2) Test Procedure (a) Trunk seizure with TKSL key Whether dialing RT No. + TRK No. OR Dialing C.O. Line NO. is determined per ASYD command, SYS1. INDEX68. b1. C.O. Line No. is assigned by ACOC command. Press TKSL or TRKSL key (RBT) + “xxx” RT No.“xxx” TRK No. or...