NEC Neax 2400 Ipx Hotel Office Data Specification

NDA-24315 COMMAND LIST
Page v
Issue 1
HOTEL COMMAND LIST IN ALPHANUMERIC ORDER
COMMAND 
NAMEFULL COMMAND NAMEPA G E
AACLAssignment of Administration Station Class244
AANPAssignment of Administration Numbering Plan91
AASNAssignment of Alternated Administration Station Number243
AASPAssignment of Administration Special Access Code101
AASTAssignment of Administration Station Data237
ADNRAssignment of Day/Night Restriction235
ADSSAssignment of Direct Station Select253
AGCLAssignment of Guest Station...

COMMAND LIST NDA-24315
Pag e vi
Issue 1
This page is for your notes. 

NDA-24315 CHAPTER 1
Page 1
Issue 1
CHAPTER 1 INTRODUCTION
1. General
This manual describes how to operate the Maintenance Administration Terminal (MAT) and plan the office
data. It also contains descriptions of the parameters for the NEAX2400 IPX.
2. How to Follow This Manual
The contents of this manual are:
• CHAPTER 1 INTRODUCTION
This chapter explains how to use this manual.
CHAPTER 2 ASSIGNMENT
This chapter explains the system configuration and system specifications required to install and run the...

CHAPTER 1 NDA-24315
Page 2
Issue 1
This page is for your notes. 

NDA-24315 CHAPTER 2
Page 3
Issue 1
ASSIGNMENT
CHAPTER 2 ASSIGNMENT
1. General
This chapter describes the information needed to install and operate the Maintenance Administration Terminal
(MAT) software.
The IPX MAT software has the following functions:
 Allows user-friendly Graphical User Interface (GUI) with Microsoft Windows 95/NT.
 Provides both an Ethernet interface and a RS232C interface.
 Allows access to a node within the Fusion Link network using a simple Login operation,
 Supports remote...

CHAPTER 2 NDA-24315
Page 4
Issue 1
ASSIGNMENT
2.2 IPX MAT and IPX Connection
Figure 2-1 shows a serial/direct connection to the IOC card of IPX. The serial/direct connection allows you
to access the IPX and the different nodes via the Fusion Link.
Figure 2-1   Serial/Direct Connection to IPX
IPX MAT software supports serial/direct connection to the target IPX. As seen in Figure 2-2, a modem is
required at both the remote maintenance center and the IPX site. The LINE port of the modem located at
the IPX...

NDA-24315 CHAPTER 2
Page 5
Issue 1
ASSIGNMENT
2.3 Serial/Dialup Connection to IPX
Figure 2-2   Serial/Dialup Connection to IPX
The IPX MAT software provides an advanced communication software for IPX. IPX is maintained via the
LAN, WAN, or TCP/IP network on which it is running. Figure 2-3 shows the simple configuration of the
TCP/IP connection. Using this connection, any node within the Fusion Link network can be accessed from
IPX MAT.
Figure 2-3   TCP/IP Connection to Dual CPR of IPX
FUSION LINK
IPX...

CHAPTER 2 NDA-24315
Page 6
Issue 1
ASSIGNMENT
Figure 2-4 shows the configuration of the PBX and IPX MAT when connecting to an existing LAN. In most
cases you should use a network device such as a HUB or bridge to provide isolation from excessive network
traffic.
Figure 2-4   TCP/IP Connection (IP Address over the External LAN)
3. TCP/IP Considerations
The IPX MAT can communicate with the IPX via an Ethernet TCP/IP connection. In order for the IPX MAT to
communicate via TCP/IP, the PC must have its...

NDA-24315 CHAPTER 2
Page 7
Issue 1
ASSIGNMENT
If the PC does not have the network software installed and configured, a message indicating that the WINSOCK
2 setup has failed displays during the IPX MAT installation. This message is an expected response since the IPX
MAT installation program attempts to upgrade the TCP/IP WINSOCK drivers to the latest version. If these
drivers are not already installed, the upgrade process fails. The failure does not affect the successful installation
and operation of the...

CHAPTER 2 NDA-24315
Page 8
Issue 1
ASSIGNMENT
3. Enter your name and your company name on the User Information dialog box. Then, click Next.
Figure 2-6   IPX MAT User Information Dialog
4. Click Next on the Choose Destination Location dialog box to install the IPX MAT software in the default
directory.
Note:If you wish to install the software in another directory, you can click Browse to display a dialog box that
allows you to select or create another directory.
Figure 2-7   Choose Location Destination...