NEC Neax 2400 Imx System Operations And Maintenance Manual

CHAPTER 8 NDA-24238
Page 614
Revision 3.0
MAINTENANCE COMMANDS
Figure 8-1   Port Status Report (MG) Display
Table 8-7 provides a list of the circuit cards and the working status of PM in each group.
Table 8-7  Type of Circuit Cards
TYPE OF CIRCUIT CARD FUNCTION NAME
LC Line Circuit
TK Analog Trunk
RS Register Sender
AI Attendant Interface
DL Digital Line Circuit
CF 3-Party Conference
MO Modem Pool Trunk
DT Digital Interface Trunk
DS DST
DT Digital Trunk
SPTS (Scanning of Port Status)
1: by MG
2: by MG,...

NDA-24238 CHAPTER 8
Page 615
Revision 3.0
MAINTENANCE COMMANDS
Type 2: By MG, Unit
Display of Scanning by Designating Unit (Figure 8-2)
Port Status on
Circuit Card Basis
ID: On-Line Status
BY: Make Busy/Not Mounted
Port Status on 
Circuit Level Basis
0: Not Assigned
1: Line Idle
2: Line Busy
3: Make Busy
4: Lockout
5: Status 5
Figure 8-2   Port Status Report (MG, Unit) Display
SPTS (Scanning of Port Status)
1: by MG
2: by MG, Unit
3: by MG, Unit, GrouMG0Interval10
SCAN
STOPEXIT
Ty p e
Dynamic Port Status...

CHAPTER 8 NDA-24238
Page 616
Revision 3.0
MAINTENANCE COMMANDS
Type 3: By MG, Unit, Group
Display of Scanning by Designating Group 
When Group is Designated (Figure 8-3)
STATUS: Idle = Idle
-- = Unassigned Port
TN: Tenant Number
STN: Station Number
TEC: Telephone Equipment Class
Figure 8-3   Port Status Report (MG, Unit, Group) Display—Designating Group
SPTS (Scanning of Port Status)
1: by MG
2: by MG, Unit
3: by MG, Unit, GrouMG0Interval10
SCAN
STOPEXIT
Ty p e
Dynamic Por t Status Repor t...

NDA-24238 CHAPTER 8
Page 617
Revision 3.0
MAINTENANCE COMMANDS
When Group-Trunk is Designated (Figure 8-4)
RT: S e e  Table 8-8.
TK: Trunk Number
TCL: Trunk Class
Figure 8-4   Port Status Report (MG, Unit, Group) Display—Designating Group-Trunk
Table 8-8  Route Number Explanation
DATA MEANING DATA MEANING
901 Attendant Console 902 Originating Register Trunk
903 Incoming Register Trunk 904 MF Receiver
905 Sender Trunk DP/PB 906 PB Receiver for Automated Attendant Service
907AMP 908Not used
909 Three-Way...

CHAPTER 8 NDA-24238
Page 618
Revision 3.0
MAINTENANCE COMMANDS
SRTS:Scanning of Route Status
1. Functional Outline
This command displays the designated trunk status (busy/idle) at predetermined intervals. A maximum of 15
routes can be scanned.
2. Parameters
Input data
RT: R o u t e  N u m b e r
Interval Time
Display data
Number of Idle TK
Number of Busy 

NDA-24238 CHAPTER 8
Page 619
Revision 3.0
MAINTENANCE COMMANDS
XHFD:X-RAY HD or FDD Diagnosis
1. Functional Outline
This command is used to execute the following diagnoses.
 Hard Disk Diagnosis
By executing read/write check on the files in the hard disk of the PBX, this command diagnoses the hard
disk for its normality.
If an error has been found as a result of the diagnosis, this command displays the information on the faulty
logical drive and the number of faulty sectors on the MAT screen. The...

CHAPTER 8 NDA-24238
Page 620
Revision 3.0
MAINTENANCE COMMANDS
Display Data
FAULT DRIVE: Fault Drive Number [0-4]
0=-
1=#0
2=#1
3=#2
4=#3
FAULT SECTOR: Number of Fault Sector [0-65535]
MESSAGE: Result of diagnosis [0-255]
0=Normal End
1=Hard disk read test practice error
2=Floppy disk drive cleaning practice error
3=Common part parameter error (Data length error)
4=FDD cleaning abnormal end (FD not in drive)
5=Individual part parameter error (Function error)
6=Individual part parameter error (Sub...