NEC Neax 2400 Imx Installation Manual

NDA-24234 LIST OF FIGURES
Page xi
Revision 3.0
LIST OF FIGURES  (CONTINUED)
Figure TitlePage
Figure 5-1 Example of Entry to Test Check Column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   308
Figure 026-1 How to Perform a Control System Changeover (Single IMG Configuration)   . . . . . . . . . . 314
Figure 026-2 How to Perform a Control System Changeover (Multiple IMG Configuration)   . . . . . . . . . 314
Figure 026-3 LEDs and Switches on TSW/MUX   . . . . . . . . . . . . ....

LIST OF FIGURES NDA-24234
Pag e xii
Revision 3.0
This page is for your notes. 

LIST OF TABLES
Table TitlePage
NDA-24234 LIST OF TABLES
Page xiii
Revision 3.0 Table 2-1 Temperature and Humidity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   8
Table 2-2 Typical Installation Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   13
Table 2-3 Conditions for Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   15
Table 2-4...

LIST OF TABLES NDA-24234
Page  xiv
Revision 3.0
LIST OF TABLES  (CONTINUED)
Table TitlePage
Table 011-13 Inter-Frame Alarm Bus Cable Connection for IMG0-IMG3  . . . . . . . . . . . . . . . . . . . . . . .   184
Table 013-1 Cable Support Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   196 

NDA-24234 SAFETY CONSIDERATIONS
Page xv
Revision 3.0
SAFETY CONSIDERATIONS
IMPORTANT — SAVE THESE INSTRUCTIONS
(1) Never install telephone wiring during a lightning storm.
(2) Never install telephone jacks in wet locations unless the jack is specifically designed for wet loca-
tions.
(3) Never touch uninsulated telephone wires or terminals unless the telephone line has been discon-
nected at the network interface.
(4) Use caution when installing or moving telephone lines.
When using your telephone...

SAFETY CONSIDERATIONS NDA-24234
Page xvi
Revision 3.0
(15) Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid
of any kind on the product.
(16) To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified ser-
viceman when some service or repair work is required. Opening or removing covers may expose
you to...

NDA-24234 REGULATORY INFORMATION
Page xvii
Revision 3.0
REGULATORY INFORMATION
1. REGULATORY REQUIREMENTS
The Federal Communications Commission (FCC) has established rules that permit the NEAX2400 IMX to be
directly connected to the telephone network. A jack is provided on party lines or coin lines.
The telephone company may make changes in its technical operations and procedures. If such changes affect
the compatibility or use of the NEAX2400 IMX, the telephone company is required to give adequate...

REGULATORY INFORMATION NDA-24234
Page xviii
Revision 3.0
3.2 Service Requirements
In the event of equipment malfunction, all repairs will be performed by NEC or an authorized distributor of
NEC. It is the responsibility of users requiring service to report the need for service to NEC or to one of their
authorized distributors.
If the equipment causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. If advance notice...

NDA-24234 REGULATORY INFORMATION
Page xix
Revision 3.0
Routed to a recorded announcement that can be administered by the CPE user
Routed to a dial prompt
(b) This equipment returns answer supervision on all DID calls forwarded to the PSTN. Permissible ex-
ceptions are:
A call is unanswered
A busy tone is received
A reorder tone is received.
EQUAL ACCESS REQUIREMENTS
This equipment is capable of providing users access to interstate providers of operator services through the use
of access codes....

REGULATORY INFORMATION NDA-24234
Page xx
Revision 3.0
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the
local telecommunications company. The equipment must also be installed using an acceptable method of con-
nection. In some cases, the company’s inside wiring associated with a single line individual service may be ex-
tended by means of a certified connector assembly (telephone extension cord). The customer should be aware
that...