NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-M03 (M03)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 375
Switch Settings
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE:
The JP1A and JP1B must be set to the same position each other.
SWITCH
NAMESWITCH
NUMBERSETTING...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-M10 (M10)
NEAX2000 IVS2 Installation Procedure ManualPage 376ND-70928 (E), Issue 1.0
PN-M10 (M10)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
CK0 Green Remains lit when a Digital Trunk Interface is connected to No. 0
circuit on this card.
CK1 Green Remains lit when a Digital Trunk Interface is connected to No. 1
circuit on this card.
TALM Red Remains lit when optical output is stopped.
RALM Red Remains lit when...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-M10 (M10)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 377
Switch Settings
NOTE 1:
Set the groove on the switch to the desired position
NOTE 2:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
JP0, 1
(Jumper pin)UPWhen connected to E1 (2M) Digital
Trunk Interface.
DOWNWhen connected to T1 (1.5M) Digi-
tal Trunk...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2ODTA (ODT)
NEAX2000 IVS2 Installation Procedure ManualPage 378ND-70928 (E), Issue 1.0
PN-2ODTA (ODT)
Locations of Lamps, Switches, and Connectors
Lamp Indications
Switch Settings
This card has no switches.
LAMP 
NAMECOLOR FUNCTION
BL0, 1 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
BL1
BL0
CN1 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2ODTB (ODT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 379
PN-2ODTB (ODT)
Locations of Lamps, Switches, and Connectors
Lamp Indications
Switch Settings
This card has no switches.
LAMP 
NAMECOLOR FUNCTION
BL0, 1 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
BL1
BL0
CN1 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-8RSTA (PBR)
NEAX2000 IVS2 Installation Procedure ManualPage 380ND-70928 (E), Issue 1.0
PN-8RSTA (PBR)
Locations of Lamps, Switches, and Connectors
Lamp Indications
This card has no lamps.
Switch Settings
This card has no switches. 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-TNTA (TNT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 381
PN-TNTA (TNT)
Locations of Lamps, Switches, and Connectors
Lamp Indications
This card has no lamps.
JAC K1
JAC K0 SW 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-TNTA (TNT)
NEAX2000 IVS2 Installation Procedure ManualPage 382ND-70928 (E), Issue 1.0
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW
(Piano Key SW)
1, 2Volume adjustment for No.0 circuit
3, 4Volume adjustment for No.1 circuit
4 
3 
2 
1 OFF
ON
SWITCH NUMBER
VO L U M E
12
OFF OFF–10dB
ON OFF–7dB
OFF ON–4dB
ON ON–1dB
SWITCH NUMBER
VO L U M E
34
OFF OFF–10dB
ON OFF–7dB
OFF ON–4dB
ON ON–1dB 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-4VCTH (VCT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 383
PN-4VCTH (VCT)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
BL0-3 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
SW1 BL3 
BL2 
BL1 
BL0
IPT
EXPFROM PN-IPTA CONNECTOR OR 
FROM OTHER PN-4VCTH CARD...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-4VCTH (VCT)
NEAX2000 IVS2 Installation Procedure ManualPage 384ND-70928 (E), Issue 1.0
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW1
(Piano Key SW)
1, 2Set the number per VCT...