NEC Neax 2000 Ivs Remote Pim System Manual

							 ND-46550 (E) CHAPTER 3
Pag e 33
Revision 2.0 Figure 3-13    DAIA-DAIC Cable Connection (Continued)
(2) Multiple PIM Configuration (continued)
DAICBUS
• When mounting 3 DAIA cards and 6 DAIC cards on last PIM
CN2
CN1
DAIA
CN1 CN2 PIM0
DA I C
TBUS
RBUS LAST PIM
 : RMT PCM-0.3 CA
 : 48-TW-0.2 CONN CA
 : 48 TW-0.7 CONN CA
 : 17-TW-0.3 CONN CA-A
BUS
DA IC DAIA DA I C
DAIC DAIA DAIC
PCM0PCM1 
						

							CHAPTER 3 ND-46550 (E)  
Pag e 3 4
Revision 2.0
2.2 Installation Procedure for Remote Site
2.2.1 Switch Setting of DAIB Card
(1) Location of Lamps, Switches, and Connectors (see Figure 3-14)
Figure 3-14    PN-DAIB Card
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
BUS
CN SENSE
RUN
MB
SW1
LINK
RED
RMTLOOP
BL
JPS
JPR
SW2
SW3 
						

							 ND-46550 (E) CHAPTER 3
Pag e 35
Revision 2.0
(2) Lamp Indications (see Table 3-6)
Table 3-6  Lamp Indications on PN-DAIB Card
LAMP NAME COLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Lights when a link between this card and a distant office is connected nor-
mally. Goes out after 15 seconds of link disconnection.
RED Red Lights when detecting PCM signal loss or Frame Alignment signal loss.
RMT Red Lights when receiving a alarm signal from a distant office.
LOOP – Not used
BL Red Lights while data transmission on control channel (D ch). Flashes while 
FP data downloading. 
						

							CHAPTER 3 ND-46550 (E)  
Pag e 3 6
Revision 2.0
(3) Switch Settings
In Table 3-7, the figure in the SWITCH NAME column and the position in   in the SETTING POSI-
TION column indicate the standard setting of the switch. When the switch is not set as shown by the figure
and  , the setting of the switch varies with the system concerned.
Table 3-7  Switch Settings on PN-DAIB Card
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SW1 (Rotary 
SW)0 – F Always set to 0
1 – F Not used
MB (Toggle SW)
Note
UP For make-busy
For normal operation
SW1 (Piano Key 
SW)
1Always set to OFF
2Always set to OFF
3Always set to OFF
4
Always set to OFF
0
ON
OFF
ON
OFF
4
3
2
1
OFF
OFF
OFF
OFF 
						

							 ND-46550 (E) CHAPTER 3
Pag e 37
Revision 2.0
SW2 (Dip SW) 1 ON Control channel signaling data transmission speed: 
48 Kbps
Control channel signaling data transmission speed: 
64 Kbps
2ON
DTI frame configuration: 12-Multi Frame
DTI frame configuration: 24-Multi Frame
3ONLine code: AMI with ZCS
Line code: B8ZS
4 ON Setting of control signal time slot
* Time slot number 0, 20, 21, and 22 (TS0/20/21/22) 
cannot be used for control signal.
** This setting must be identical with the opposite 
DAIA card. 5ON
6ON
7
OFF
8ON Table 3-7  Switch Settings on PN-DAIB Card (Continued)
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
ON2 134 6857OFF
OFF
OFF
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFFONONONON TS1
ON OFF ON ON ON TS2
OFF OFF ON ON ON TS3
ON ON OFF ON ON TS4
OFF ON OFF ON ON TS5
ON OFF OFF ON ON TS6
OFF OFF OFF ON ON TS7
ON ON ON OFF ON TS8
OFF ON ON OFF ON TS9
ON OFF ON OFF ON TS10
OFF OFF ON OFF ON TS11
ON ON OFF OFF ON TS12
OFF ON OFF OFF ON TS13
ON OFF OFF OFF ON TS14
OFF OFF OFF OFF ON TS15
ON ON ON ON OFF TS16
OFFONONONOFF TS17
ON OFF ON ON OFF TS18
OFF OFF ON ON OFF TS19
OFF OFF OFF ON OFF TS23
OFF
OFF
OFF
ON
OFF 
						

							CHAPTER 3 ND-46550 (E)  
Pag e 3 8
Revision 2.0 Note:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplugging the circuit card. SW3 (Dip SW) 1 Set the equalizer according to the cable length 
between the system and the CSU.
OFF
2
OFF
3
OFF
4 Always set to OFF.
JPS (Jumper pin) UP Neutral grounding on the transmitting line is 
provided.
Neutral grounding on the transmitting line is not 
provided.
JPR (Jumper pin) UP Neutral grounding on the receiving line is provided.
Neutral grounding on the receiving line is not 
provided. Table 3-7  Switch Settings on PN-DAIB Card (Continued)
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
ON2 134
ON
SW-1 SW-2 SW-3 CABLE LENGTH
ON ON ON 0 - 131.2 ft. (0 - 40 m)
ON ON OFF 131.2 - 262.5 ft. (40 - 80 m)
ON OFF ON 262.5 - 394 ft. (80 - 120 m)
ON OFF OFF 394 - 525 ft. (120 - 160 m)
OFF ON ON 525 - 656 ft. (160 - 200 m)
OFF OFF OFF Signal is not sent
ON
ON
OFF
DOWN
DOWN 
						

							 ND-46550 (E) CHAPTER 3
Pag e 39
Revision 2.0
2.2.2 Mounting of DAIB Card
STEP 1:
Set MB switch on the DAIB card to up position.
STEP 2:
Mount DAIB card in the MP slot on the Remote PIM. 
STEP 3:
After mounting the card, set MB switch to down position.
Figure 3-15    Mounting Location of DAIB Card
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
Remote PIM
DAIB CARD
LT00LT01LT02LT03LT04LT05LT06LT07LT08LT09LT10MP
P
W
R
• Small Platform 
						

							CHAPTER 3 ND-46550 (E)  
Pag e 4 0
Revision 2.0Figure 3-16    Mounting Location of DAIB Card (Continued)
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
Remote PIM
DAIB CARD
LT00LT01LT02LT03LT04LT05LT06LT07LT08MP
P
W
R
•
1000 IVS 
						

							 ND-4 655 0 (E)   CHAPTER 3
Set M B s wit ch  on  DA IC  c a rd  t o  up  posit ion.
M ount  DA IC  ca rd in th e AP  slot on th e Re mote P IM .
Afte r  m ounting  all  DA IC  c ar ds ,  s e t  M B sw it c h  on  DA IB  c ar d to  u p,  an d t h en d own.
A TTE NTIO N
Rem ote PIM
DA IC CARD
LT 00LT01LT02LT03LT04LT05
LT06/A P00LT 07/A P01LT 08/A P02LT 09/A P03LT 10/A P04
MP
•
S m all Pl atfo rm
AP0 5 
						

							CHAPTER 3 ND-46550 (E)  
Pag e 4 2
Revision 2.0Figure 3-18    Mounting Location of DAIC Card (Remote PIM) (Continued)
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
Remote PIM
DAIC CARD
LT00LT01LT02LT03
LT04/AP00LT05/AP01LT06/AP02LT07/AP03LT08/AP04MP
P
W
R
•
1000 IVS