NEC Nc900ca Manual

21
2. \bnstallation and\fi Connection
Removing the power cable from the power cable stopper
1 Push the clamper of \lthe power cable stopper to unclasp it. 
knob
2 Push the power cable clamper to open it wide eno\lugh to pull out the power cable. 
knob
clamper 

22
2. Installation an\Bd Connection
2-3. Connecting the imag\re input termina\fs
The IMB \fNC-9\bMS\b1) is mounted as standard in this projector. Alternately, you can use an HDSDI input port or DVD-D input 
port by replacing this with\B a signal input bo\Bard \fNC-8\bLB\b1-B/NC-8\bDS\b\B1-B) which is sold \Bseparately.
The video input ports that can be used with each board are as follows. Refer to the instruction manual of the IMB or signal input 
board for details on c\Bonnecting the vide\Bo input ports...

23
 
3.
\fr\bjecti\bn \bf Images 
(Basic Operati\bn)
3-1. Steps of projecting images
• Step 1 
Turn on the power to \fithe projector. (See page 24) 
• Step 2 
Select the title o\fif input signal. (Se\fie page 27) 
• Step 3 
Adjust the positio\fin and size of the \fiprojected screen. (See page 28) \fi
• Step 4 
Turn off the power to the\fi projector. (See page 35)   

24
3. Projection of \bmages \fi(Basic Operation)
3-2. Turning your projector on
\freparati\bn: • Connect the power \fica\fle to the projector. (See page 17)
  • Supply AC power to\fi the projector.
NO TE• Turn off the main power s\fiwitch to the projector when suppl\fiying or cutting AC \fipower to the projector.
Supplying or shutti\fing down the AC powe\fir while the main p\fiower switch is on \fiwill damage the projector. 
•  Turning  on  and  off  the  projector  involves  a  two-step  operation;  the...

25
3. Projection of \bmages \fi(Basic Operation)
3 Turn on the main power switch on the side \lof the projector. 
A \fuzzer will ring on the projector. The POWER \futton indicator will \flink green and the STATUS indicator will light 
orange (stand\fy state). KEY LOCK \fecomes automatically on if no control panel operation takes place in the stand\fy 
state for 30 secon\fids \fy default. Butt\fions on the control panel do not fu\finction while KEY L\fiOCK is on. (See pa\fige 33)
Main power switch
VOLTAGE...

26
3. Projection of \bmages \fi(Basic Operation)
6 Press the LAMP O\f/OFF\l button on the control panel for five seconds or longer. 
The lamp is turned on and the screen glows light a\fout 15 seconds later. The LAMP ON/OFF \futton indicator \flinks 
in cycles of 2 (an\fid changes to steady\fi green light 90 second\fis later). 
The  douser  is  closed  until  the  screen  glows  light  (the  DOUSER  \futton  indicator  lights  green).  When  the  douser  is 
open, the DOUSER \fu\fitton indicator tur\fins...

27
3. Projection of \bmages \fi(Basic Operation)
3-3. Selecting the title\l of input signal
This  projector  allows  you  to  select  pre-registered  title  (input  signal)  using  the  preset  \futtons  on  the  control  panel  (up  to  16 
titles). Request your dealer/distri\futor \fifor details on registering and changing titles. This section explains the steps for select-
ing registered titles. 
1 Turn on the power to the image devices connected to the projector. 
2 Press the ME\fU button. 
3 Press...

28
3. Projection of \bmages \fi(Basic Operation)
3-4. Adjusting the position and the size of projected screen
3-4-1. Displaying the test pattern 
1 Press the ME\fU button, or select a test pattern from preset buttons (button  to ).
\bf you register the test pa\fitterns to the preset \futtons ( t\fio  \futtons), sel\fiect the test patte\firn according to “3-3. 
Selecting the title\fi of input signal (S\fiee page 27)”.
2 Press the LEFT/RIGHT button to display “Title Select” on the LCD screen.
3 Press the...

29
3. Projection of \bmages \fi(Basic Operation)
7 Display  on  the  LCD  the  name  of  the  test  pattern  to  be  projected,  then  press  the  E\fTER 
button. 
The test pattern is displayed. 
To cancel the test \fipattern display, select the title\fi of the signal to p\firoject or select th\fie “OFF” test patte\firn. 
3-4-2. Adjusting the positi\lon of the projected screen (Lens shift) 
1 Press the ME\fU button.
2 Press the LEFT/RIGHT button to display “Configuration” on the LCD screen.
3 Press the...

30
3. Projection of \bmages \fi(Basic Operation)
3-4-3. Adjustment of the s\lize (zoom) and focus of the projected screen
1 Press the ME\fU button.
2 Press the LEFT/RIGHT button to display “Configuration” on the LCD screen.
3 Press the DOW\f button.
4 Press the LEFT/RIGHT button to display “Lens Control” on the LCD screen.
5 Press the DOW\f button.
The screen (“Lens Positio\fin”) to adjust the \fiposition of the pr\fiojected screen is displayed. \fi
6 Press the E\fTER button.
The screen to adjust the...