NEC Nc1600c Dlp Cinema Projector Users Manual
Here you can view all the pages of manual NEC Nc1600c Dlp Cinema Projector Users Manual. The NEC manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
21 3. Projection of Images (Basic Operation) 3-2. Turning your projector on Preparation: Supply AC power to the projector head.Please contact your dealer/distributor to connect the power cable. NOTE•Turn off the main power switch to the projector head when supplying or cutting AC power to the projector. If power is supplied or cut while the main power switch is turned on, the projector will be damaged. • Be sure to turn your projector on or off in two steps of operation with the “main power switch” and...
Page 22
![Page 22
22
3. Projection of Images (Basic Operation)
3Press the POWER button on the control panel of your projector three seco\
nds or longer.
Your projector is turn on, and the screen glows light about 30 seconds later. The POWER indicator of the projector lights
up green.
• When controlling with the remote control, press the POWER ON button three seconds or longer.
NOTE•While your projector is on, be sure to have the lens cap removed from the lens.
Otherwise, the lens cap may get deformed due to a heat...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-21.png "Page 22
22
3. Projection of Images (Basic Operation)
3Press the POWER button on the control panel of your projector three seco\
nds or longer.
Your projector is turn on, and the screen glows light about 30 seconds later. The POWER indicator of the projector lights
up green.
• When controlling with the remote control, press the POWER ON button three seconds or longer.
NOTE•While your projector is on, be sure to have the lens cap removed from the lens.
Otherwise, the lens cap may get deformed due to a heat...")
22 3. Projection of Images (Basic Operation) 3Press the POWER button on the control panel of your projector three seco\ nds or longer. Your projector is turn on, and the screen glows light about 30 seconds later. The POWER indicator of the projector lights up green. • When controlling with the remote control, press the POWER ON button three seconds or longer. NOTE•While your projector is on, be sure to have the lens cap removed from the lens. Otherwise, the lens cap may get deformed due to a heat...
Page 23
![Page 23
23
3. Projection of Images (Basic Operation)
3-3. Selecting the title of input signal
This projector allows you to select pre-registered signals using the signal selection buttons on the control panel (up to 8
signals). Request your dealer/distributor for details on registering and changing titles. This section explains the steps for
selecting registered signals.
1Turn on the power to the image devices connected to the projector.
2Press the MENU button.
3Press the [MENU CTL] LEFT/RIGHT button to display...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-22.png "Page 23
23
3. Projection of Images (Basic Operation)
3-3. Selecting the title of input signal
This projector allows you to select pre-registered signals using the signal selection buttons on the control panel (up to 8
signals). Request your dealer/distributor for details on registering and changing titles. This section explains the steps for
selecting registered signals.
1Turn on the power to the image devices connected to the projector.
2Press the MENU button.
3Press the [MENU CTL] LEFT/RIGHT button to display...")
23 3. Projection of Images (Basic Operation) 3-3. Selecting the title of input signal This projector allows you to select pre-registered signals using the signal selection buttons on the control panel (up to 8 signals). Request your dealer/distributor for details on registering and changing titles. This section explains the steps for selecting registered signals. 1Turn on the power to the image devices connected to the projector. 2Press the MENU button. 3Press the [MENU CTL] LEFT/RIGHT button to display...
Page 24
![Page 24
24
3. Projection of Images (Basic Operation)
3-4. Adjusting the position and the size of projected screen
3-4-1. Displaying the test pattern
1Press the TEST button on the remote control. Alternatively, select the test pattern from the signal
selection button.
If you register the test patterns to the signal selection buttons ( to buttons), select the te\
st pattern according to
“3-3. Selecting the title of input signal (See page 23)”.
The mode for selecting the test pattern is set.
2Press the SELECT /...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-23.png "Page 24
24
3. Projection of Images (Basic Operation)
3-4. Adjusting the position and the size of projected screen
3-4-1. Displaying the test pattern
1Press the TEST button on the remote control. Alternatively, select the test pattern from the signal
selection button.
If you register the test patterns to the signal selection buttons ( to buttons), select the te\
st pattern according to
“3-3. Selecting the title of input signal (See page 23)”.
The mode for selecting the test pattern is set.
2Press the SELECT /...")
24 3. Projection of Images (Basic Operation) 3-4. Adjusting the position and the size of projected screen 3-4-1. Displaying the test pattern 1Press the TEST button on the remote control. Alternatively, select the test pattern from the signal selection button. If you register the test patterns to the signal selection buttons ( to buttons), select the te\ st pattern according to “3-3. Selecting the title of input signal (See page 23)”. The mode for selecting the test pattern is set. 2Press the SELECT /...
Page 25
![Page 25
25
3. Projection of Images (Basic Operation)
3-4-3. Fine adjustment of the size of the projected screen (Zoom)
1Press the ZOOM +/- buttons while depressing the CTL (LENS) button on t\
he control panel of your
projector as required.
• When controlling with the remote control, press the ZOOM +/- button while depressing the CTL (LENS) button.
3-4-4. Focusing the projected screen (Focus)
1Press the FOCUS +/- buttons while depressing the CTL (LENS) button, on\
the control panel of
your projector as...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-24.png "Page 25
25
3. Projection of Images (Basic Operation)
3-4-3. Fine adjustment of the size of the projected screen (Zoom)
1Press the ZOOM +/- buttons while depressing the CTL (LENS) button on t\
he control panel of your
projector as required.
• When controlling with the remote control, press the ZOOM +/- button while depressing the CTL (LENS) button.
3-4-4. Focusing the projected screen (Focus)
1Press the FOCUS +/- buttons while depressing the CTL (LENS) button, on\
the control panel of
your projector as...")
25 3. Projection of Images (Basic Operation) 3-4-3. Fine adjustment of the size of the projected screen (Zoom) 1Press the ZOOM +/- buttons while depressing the CTL (LENS) button on t\ he control panel of your projector as required. • When controlling with the remote control, press the ZOOM +/- button while depressing the CTL (LENS) button. 3-4-4. Focusing the projected screen (Focus) 1Press the FOCUS +/- buttons while depressing the CTL (LENS) button, on\ the control panel of your projector as...
Page 26
![Page 26
26
3. Projection of Images (Basic Operation)
3-5. Turning on/off the lamp with the projector turned on
3-5-1. Turning off the lamp
1Press the LAMP OFF button while depressing the CTL (LAMP) button, on t\
he control panel of your
projector as required.
3-5-2. Turning on the lamp
1Press the LAMP ON button while depressing the CTL (LAMP) button, on th\
e control panel of your
projector as required.](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-25.png "Page 26
26
3. Projection of Images (Basic Operation)
3-5. Turning on/off the lamp with the projector turned on
3-5-1. Turning off the lamp
1Press the LAMP OFF button while depressing the CTL (LAMP) button, on t\
he control panel of your
projector as required.
3-5-2. Turning on the lamp
1Press the LAMP ON button while depressing the CTL (LAMP) button, on th\
e control panel of your
projector as required.")
26 3. Projection of Images (Basic Operation) 3-5. Turning on/off the lamp with the projector turned on 3-5-1. Turning off the lamp 1Press the LAMP OFF button while depressing the CTL (LAMP) button, on t\ he control panel of your projector as required. 3-5-2. Turning on the lamp 1Press the LAMP ON button while depressing the CTL (LAMP) button, on th\ e control panel of your projector as required.
Page 27
![Page 27
27
3. Projection of Images (Basic Operation)
3-6. Turning your projector off
1Press the POWER button on the projector control panel for three seconds \
or longer.
The power to the projector is turned off. The POWER indicator and rear STATUS indicator will blink in orange
(cooling state).
The fan will continue to rotate while cooling, and the amount of time remaining for cooling is displayed on the LCD
screen. The cooling-off time is 5 minutes.
When cooling has ended, the POWER indicator and the rear...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-26.png "Page 27
27
3. Projection of Images (Basic Operation)
3-6. Turning your projector off
1Press the POWER button on the projector control panel for three seconds \
or longer.
The power to the projector is turned off. The POWER indicator and rear STATUS indicator will blink in orange
(cooling state).
The fan will continue to rotate while cooling, and the amount of time remaining for cooling is displayed on the LCD
screen. The cooling-off time is 5 minutes.
When cooling has ended, the POWER indicator and the rear...")
27 3. Projection of Images (Basic Operation) 3-6. Turning your projector off 1Press the POWER button on the projector control panel for three seconds \ or longer. The power to the projector is turned off. The POWER indicator and rear STATUS indicator will blink in orange (cooling state). The fan will continue to rotate while cooling, and the amount of time remaining for cooling is displayed on the LCD screen. The cooling-off time is 5 minutes. When cooling has ended, the POWER indicator and the rear...
Page 28
![Page 28
28
4-1. Basic operation with adjustment menus
To adjust the projector, display the menu on the LCD screen of the projector control panel.
4-1-1. Screen display
The menu display screen is composed of a menu display field (the upper two lines) and a se\
tting item display field (the bottom
two lines).
← Displays the main menu or submenus.
← Displays submenus or selection items.
← Displays settings and selection status.
← Displays settings, selected items and information on selected menus.
The...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-27.png "Page 28
28
4-1. Basic operation with adjustment menus
To adjust the projector, display the menu on the LCD screen of the projector control panel.
4-1-1. Screen display
The menu display screen is composed of a menu display field (the upper two lines) and a se\
tting item display field (the bottom
two lines).
← Displays the main menu or submenus.
← Displays submenus or selection items.
← Displays settings and selection status.
← Displays settings, selected items and information on selected menus.
The...")
28 4-1. Basic operation with adjustment menus To adjust the projector, display the menu on the LCD screen of the projector control panel. 4-1-1. Screen display The menu display screen is composed of a menu display field (the upper two lines) and a se\ tting item display field (the bottom two lines). ← Displays the main menu or submenus. ← Displays submenus or selection items. ← Displays settings and selection status. ← Displays settings, selected items and information on selected menus. The...
Page 29
![Page 29
29
4. Using Menus
When not displaying menus, the following screen is normally displayed.
When in standby
When the projector is in a standby state (the main power switch in on), the follo\
wing is displayed.
When power is turned on
When the power is turned on, the following is displayed.
← Displays the hours of lamp bulb use.
← Displays the lamp output (%).
← Displays the selected title.
← Displays the selected port.
When the power is turned off
The amount of time remaining for cooling is...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-28.png "Page 29
29
4. Using Menus
When not displaying menus, the following screen is normally displayed.
When in standby
When the projector is in a standby state (the main power switch in on), the follo\
wing is displayed.
When power is turned on
When the power is turned on, the following is displayed.
← Displays the hours of lamp bulb use.
← Displays the lamp output (%).
← Displays the selected title.
← Displays the selected port.
When the power is turned off
The amount of time remaining for cooling is...")
29 4. Using Menus When not displaying menus, the following screen is normally displayed. When in standby When the projector is in a standby state (the main power switch in on), the follo\ wing is displayed. When power is turned on When the power is turned on, the following is displayed. ← Displays the hours of lamp bulb use. ← Displays the lamp output (%). ← Displays the selected title. ← Displays the selected port. When the power is turned off The amount of time remaining for cooling is...
Page 30
![Page 30
30
4. Using Menus
3Press the [MENU CTL] DOWN button.
The submenu “Lamp” of “Information” is displayed.
The menu item can be selected by pressing the ENTER button instead of the SELECT DOWN button
To return to the previous state, press the [MENU CTL] UP button, or the CANCEL button.
4Press the [MENU CTL] LEFT/RIGHT button to select the submenu “Version.”
At each press of the [MENU CTL] LEFT/RIGHT button, the display will cycle as “L\
amp” ←→ “Macro Key” ←→ “Usage”
←→ “Error Code” ←→ “Version” ←→ “IP...](http://img.usermanuals.tech/thumb/54/92077/w300_nec-nc1600c-a-manual_d-29.png "Page 30
30
4. Using Menus
3Press the [MENU CTL] DOWN button.
The submenu “Lamp” of “Information” is displayed.
The menu item can be selected by pressing the ENTER button instead of the SELECT DOWN button
To return to the previous state, press the [MENU CTL] UP button, or the CANCEL button.
4Press the [MENU CTL] LEFT/RIGHT button to select the submenu “Version.”
At each press of the [MENU CTL] LEFT/RIGHT button, the display will cycle as “L\
amp” ←→ “Macro Key” ←→ “Usage”
←→ “Error Code” ←→ “Version” ←→ “IP...")
30 4. Using Menus 3Press the [MENU CTL] DOWN button. The submenu “Lamp” of “Information” is displayed. The menu item can be selected by pressing the ENTER button instead of the SELECT DOWN button To return to the previous state, press the [MENU CTL] UP button, or the CANCEL button. 4Press the [MENU CTL] LEFT/RIGHT button to select the submenu “Version.” At each press of the [MENU CTL] LEFT/RIGHT button, the display will cycle as “L\ amp” ←→ “Macro Key” ←→ “Usage” ←→ “Error Code” ←→ “Version” ←→ “IP...