NEC Nc1600c Dlp Cinema Projector Users Manual

							
21
3. Projection of Images (Basic Operation)
3-2. Turning your projector on
Preparation: Supply AC power to the projector head.Please contact your dealer/distributor to connect the power cable.
NOTE•Turn off the main power switch to the projector head when supplying or cutting AC power to the projector.
If power is supplied or cut while the main power switch is turned on, the projector will be damaged.
• Be sure to turn your projector on or off in two steps of operation with the “main power switch” and the
“POWER button” (“POWER ON/OFF button” on the remote control).
•T urning power on (See this page)
[1] Turn the “main power switch” on the projector head to on.
Your projector is set in a standby state.
[2] Press the POWER button (POWER ON button on the remote control) three seconds or longer. Your projector is turn on.
•T urning power off (See page 27)
[1] Press the POWER button (POWER OFF button on the remote control) three seconds or longer. Your projector is set in a standby state.
[2] When the fan has stopped running, set the “main power switch” on the projector head to OFF. Your projector is turned off.
1Remove the lens cap.
2T urn the main power switch on the side of your projector head to on.
A buzzer will ring on the projector. The POWER indicator and rear STATUS indicator light up orange (standby state).
     
						

							
22
3. Projection of Images (Basic Operation)
3Press the POWER button on the control panel of your projector three seco\
nds or longer.
Your projector is turn on, and the screen glows light about 30 seconds later. The POWER indicator of the projector lights
up green.
• When controlling with the remote control, press the POWER ON button three seconds or longer.
NOTE•While your projector is on, be sure to have the lens cap removed from the lens.
Otherwise, the lens cap may get deformed due to a heat buildup.
• In the following instances, the power to your projector cannot be turned on even if you press the POWER
button.
- When the inside temperature is abnormally high.  The protective function prevents power from turning on.
Wait some time (until the projector inside cools down) and then turn on the power.
- When the STATUS indicator is blinking without the lamp lighting up after power-on.  Your projector may be
in trouble. Check the error display on the LCD screen and contact your dealer/distributor for instructions.
• Note that the image may sometimes flicker until the lamp has stabilized \
(5 to 10 minutes) after power-on. This
is due to the characteristics of the lamp and is not trouble of your projector. 
						

							
23
3. Projection of Images (Basic Operation)
3-3. Selecting the title of input signal
This projector allows you to select pre-registered signals using the signal selection buttons on the control panel (up to 8
signals). Request your dealer/distributor for details on registering and changing titles. This section explains the steps for
selecting registered signals.
1Turn on the power to the image devices connected to the projector.
2Press the MENU button.
3Press the [MENU CTL] LEFT/RIGHT button to display “Title Select” on the LCD screen.
At each press of the [MENU CTL] LEFT/RIGHT buttons, the display will cycle as “Title Select”  ←→ “Configuration”  ←→
“(Title Setup)”  ←→ “Information.”
4Press the [MENU CTL] DOWN button.
The title of the input signal is displayed.
•When you have made a wrong selection, press the [MENU CTL] UP button. A return will be made to the previous
menu.
5Press the [MENU CTL] LEFT/RIGHT buttons to display “Title of Signal to be Projected” on the LCD
screen.
6Press the ENTER button.
The title of the signal to be projected is selected.
•The (*) mark on the LCD indicates that this is the currently selected item. 
						

							
24
3. Projection of Images (Basic Operation)
3-4. Adjusting the position and the size of projected screen
3-4-1. Displaying the test pattern
1Press the TEST button on the remote control. Alternatively, select the test pattern from the signal
selection button.
If you register the test patterns to the signal selection buttons ( to  buttons), select the te\
st pattern according to
“3-3. Selecting the title of input signal (See page 23)”.
The mode for selecting the test pattern is set.
2Press the SELECT 
/  button.
The display of the test pattern name on the LCD switches.
3Display on the LCD the name of the test pattern to be projected, then press the ENTER button.
The test pattern is displayed.
• To cancel the test pattern display, reselect the signal to be project.
3-4-2. Adjusting the position of the projected screen (Lens shift)
1Press the [LENS CTL] UP/DOWN/LEFT/RIGHT buttons while depressing the CTL\
 (LENS) button,
on the control panel of your projector as required.
The position of the projected screen will move upward, downward, left or right.
• When controlling with the remote control, press the POSI/LENS button while depressing the CTL button. 
						

							
25
3. Projection of Images (Basic Operation)
3-4-3. Fine adjustment of the size of the projected screen (Zoom)
1Press the ZOOM +/- buttons while depressing the CTL (LENS) button on t\
he control panel of your
projector as required.
• When controlling with the remote control, press the ZOOM +/- button while depressing the CTL (LENS) button.
  
3-4-4. Focusing the projected screen (Focus)
1Press the FOCUS +/- buttons while depressing the CTL (LENS) button, on\
 the control panel of
your projector as required.
• When controlling with the remote control, press the FOCUS +/- button while depressing the CTL (LENS) button.
  
3-4-5. Adjusting the brightness of the projected screen (Lamp output)
1Press the LAMP +/- buttons while depressing the CTL (LAMP) button, on \
the control panel of your
projector as required.
   
						

							
26
3. Projection of Images (Basic Operation)
3-5. Turning on/off the lamp with the projector turned on
3-5-1. Turning off the lamp
1Press the LAMP OFF button while depressing the CTL (LAMP) button, on t\
he control panel of your
projector as required.
3-5-2. Turning on the lamp
1Press the LAMP ON button while depressing the CTL (LAMP) button, on th\
e control panel of your
projector as required. 
						

							
27
3. Projection of Images (Basic Operation)
3-6. Turning your projector off
1Press the POWER button on the projector control panel for three seconds \
or longer.
The power to the projector is turned off. The POWER indicator and rear STATUS indicator will blink in orange
(cooling state).
The fan will continue to rotate while cooling, and the amount of time remaining for cooling is displayed on the LCD
screen. The cooling-off time is 5 minutes.
When cooling has ended, the POWER indicator and the rear STATUS indicator light in orange (Standby).
• When controlling with the remote control, press the POWER OFF button for three seconds or longer.
  
2When the projector has entered the standby state, turn the main power sw\
itch on the projector
head to off.
The projector POWER indicator will extinguish and the main power will turn off.
  
3Turn off the AC power to the projector head.
NOTE• In the following instances, do not turn off the main power switch or disconnect the AC power. Doing so can
damage the projector.- While projecting images
- While the fan is running after the power is turned off (The cooling-off time is 5 minutes) 
						

							
28
4-1. Basic operation with adjustment menus
To adjust the projector, display the menu on the LCD screen of the projector control panel.
4-1-1. Screen display
The menu display screen is composed of a menu display field (the upper two lines) and a se\
tting item display field (the bottom
two lines).
← Displays the main menu or submenus. 
←  Displays submenus or selection items. 
←  Displays settings and selection status. 
←  Displays settings, selected items and information on selected menus. 
The meanings of symbols in the menu display screen are outlined below.
Indicates that there is a menu of a higher level. 
Press the [MENU CTL] UP button to return to a menu one level above. 
Indicates that there is a selected item or menu at the same level. 
Press the [MENU CTL] LEFT/RIGHT button to display other selected items or \
menus. 
Indicates that there is a menu of a lower level. 
Press the [MENU CTL] DOWN button to display the menu one level below. 
Indicates that there are setting items of a lower level. 
Press the [MENU CTL] UP button to return to a menu one level above. 
Press the [MENU CTL] DOWN button to display the setting item one level bel\
ow. 
4.
Using Menus 
						

							
29
4. Using Menus
When not displaying menus, the following screen is normally displayed.
When in standby
When the projector is in a standby state (the main power switch in on), the follo\
wing is displayed.
When power is turned on
When the power is turned on, the following is displayed.
← Displays the hours of lamp bulb use. 
←  Displays the lamp output (%). 
←  Displays the selected title. 
←  Displays the selected port. 
When the power is turned off
The amount of time remaining for cooling is displayed as shown below, when the power to the projector head is turned off.
4-1-2. Operating menus
Preparation: Turn your projector on. (See page 21)
1Press the MENU button on the control panel of your projector .
The menu is displayed in the LCD screen.
2Press the [MENU CTL] LEFT/RIGHT buttons to display “Information.”
At each press of the [MENU CTL] LEFT/RIGHT buttons, the display will cycle as “\
Title Select”  ←→ “Configuration”  ←→
“(Title Setup)”  ←→ “Information.” 
						

							
30
4. Using Menus
3Press the [MENU CTL] DOWN button.
The submenu “Lamp” of “Information” is displayed.
The menu item can be selected by pressing the ENTER button instead of the SELECT DOWN button
To return to the previous state, press the [MENU CTL] UP button, or the CANCEL button.
4Press the [MENU CTL] LEFT/RIGHT button to select the submenu “Version.”
At each press of the [MENU CTL] LEFT/RIGHT button, the display will cycle as “L\
amp”  ←→ “Macro Key”  ←→ “Usage”
←→  “Error Code”  ←→ “Version”  ←→ “IP Address”  ←→ “MMS Status.”
5Press the [MENU CTL] DOWN button.
The submenu “System” another rank lower than “Version” is displayed.
6Press the [MENU CTL] DOWN button.
The submenu “BIOS” another rank lower than “System” is displ\
ayed.
7Press the [MENU CTL] LEFT/RIGHT button to select the submenu “Data.”\
At each press of the [MENU CTL] LEFT/RIGHT button, the display will cycle as “B\
IOS”  ←→ “Firmware”  ←→ “Data”  ←→
“Serial No.,” and each version information is displayed.
8Press the [MENU CTL] UP button several times.
At each press of the [MENU CTL] UP button, the display will return to a menu one level above.